Eureka NEN110 Series Manual

Important instructions

For easy assembly, please take a few moments to read moments to read this owner's guide. If you have questions about your new vacuum, please contact our customer service HELPLINE at 1-800-282-2886. 2-2886. We're here to help!

Eureka stands by our Clean Promise seal. Learn more at www.eureka.com/cleanpromise

www.eureka.com

Please Retain
We suggest you record the model, type and serial numbers below. They are located on the bottom of your cleaner. For prompt and complete service information, always refer to these numbers when inquiring about service.
Model & Type
Serial No.
It is also important to keep your receipt as proof of date of purchase.

This Owner's Guide provides important instructions to prolong the life of your Eureka vacuum cleaner.

Registration: To register your product visit www.eureka.com and click on the 'Register Your Product' link in the top right corner.

Inspection: Carefully unpack and inspect your new Eureka vacuum cleaner for shipping damage. Each unit is tested and thoroughly inspected before shipping. For instructions regarding any shipping damage, call Eureka Customer Service HELPLINE 1-800-282-2886 immediately.

Follow caution information wherever you see this symbol.

How to identify parts of your vacuum cleaner

1. Handle
2. Dust cup release button
3. Power button
4. Cord rewind button
5. Filter
6. Dust cup

Accessories
This vacuum cleaner includes the following accessories:

1. Telescoping metal wand
2. Hose
3. Floor brush

How to assemble your vacuum cleaner

ASSEMBLY

Always disconnect the vacuum cleaner from the electrical socket before attaching or removing accessories.

1. Attach the hose to the front of the vacuum cleaner by inserting it into the air inlet and twisting to the right. To remove the hose twist to the left and pull to detach.
   
2. Attach the telescoping wand to the hose at the bend by pushing the two components together.
   
3. Attach the floor nozzle to the wand by connecting the two parts. And then twist them into position.
   

How to use your vacuum cleaner

Always switch off the vacuum cleaner before connecting or disconnecting the hose/attachments or removing and emptying the dust cup.

The vacuum cleaner is equipped with a thermal cut-off. If for any reason, the vacuum cleaner does overheat, the thermostat will automatically turn the vacuum cleaner off. If this happens, switch the vacuum cleaner off and unplug it from the electrical socket. Remove and empty the dust cup and check the vacuum cleaner for blockages. Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the incorrect space, please wait 24 hours for the filters to fully dry before putting them back into the machine).

Operation

Pull the power cord out of the vacuum cleaner and stop when you see the yellow mark. Make sure the red mark is not visible or you have pulled too far. When done cleaning, turn off the power, pull the plug out of the electrical socket, and then push the rewind button until the cord is completely retracted. To turn on the vacuum cleaner, push the plug into an electrical socket and press the power button.

Switching between carpet & hard floor

There is a switch located on the floor nozzle that can be pressed with your foot to switch between floor modes. The symbols shown below correspond to the type of floor the setting is for.

Position 1: Bristles extended for hard floor

Position 2: Bristles retracted for carpet

How to maintain your vacuum cleaner

Emptying the dust cup

Always switch off the vacuum and unplug it from the electrical socket before conducting any maintenance or cleaning.

Empty the dust cup after each use. Also be sure to empty the dust cup anytime dust reaches the max fill line.
A full dust cup will reduce the efficiency of the vacuum cleaner so be sure to empty the dust cup regularly.

1. Press the dust cup release button and take the dust cup out of the vacuum.
   
2. Bring the dust cup over a trash receptacle and then press the release button to open the lower lid. The dust will fall out the bottom and into the trash.
   
3. Close the dust cup lid after dust has been fully emptied. Return the dust cup to the vacuum cleaner.
   

Cleaning the Filter

The filter is an effective system for removing dust.

Sponge filters require cleaning on a monthly basis (or more depending on use frequency). Do not operate the vacuum cleaner without the sponge filter in place.

1. To remove the filter, pull on the dust cup lid clip and lift the cover upwards.
   
2. The filter is located inside the top cover of the dust cup. Pull on the handle of the filter housing then remove it.
   
3. Tap the filter over a bin to remove the dust.
4. Take the sponge filter out of the filter housing.
5. Wash the filter under water (max. 40 degree).
   
   DO NOT USE DETERGENTS to clean any part.
   Leave it out to dry for 24 hours or until fully dry before placing it back in the vacuum cleaner.
6. Put the filter back into the housing. Put the housing and filter back into the dust cup lid. Finally, close the dust cup lid.
7. Place the dust cup back into the vacuum cleaner until a click is heard.

Problem solving

Make sure vacuum is turned off and power cord is unplugged.

N O T I C E: Thermal cut-off
This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, proceed as follows:

1. Push the power switch to off and unplug the vacuum.
2. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum.
3. After the 30 minute period, plug the vacuum back in and turn on the switch. If the vacuum still does not work, call the Eureka Customer Service HELPLINE at 1-800-282-2886.

Connecting to an electrical socket
Please check that the voltage indicated on the product corresponds with your supply voltage.

Replacement Parts

Obtaining warranty service

To obtain warranty service you must contact the Eureka Service Team, toll free, at 1-800-282-2886 or email customerserviceusa@midea.com, to discuss the warranty claim and procedures to be followed. All warranty claims must include submission of proof-of-purchase documentation. For additional information, you may also visit www.eureka.com.

Midea America Corp.
200 Rivers Edge Drive
Medford, MA. 02155
USA

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER

To reduce the risk of fire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
• Do not use with damaged cord or plug. If cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call the Eureka Customer Service HELPLINE at 1-800-282-2886.
• Do not pull or carry by the cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle the vacuum cleaner with wet hands or operate without shoes.
• Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce
• This vacuum cleaner creates suction. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup or filter(s) in place
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use on areas where they may be present.
• Store you cleaner indoors in a cool, dry area.
• Keep your work area well lit.
• Unplug electrical appliances before vacuuming them.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
• Turn off the power switch and unplug cleaner before rotating the nozzle.

SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper autlet. DO NOT change the plug in any way.

Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly shuts off, push the on/off switch off (0) and unplug the cleaner. Check the cleaner for a possible source of overheating, such as a full dust cup, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and push the on/off switch on (l).

Do Not Oil the motor or the brushroll at any time. The bearings are permanently lubricated and sealed.

Documents / Resources

References

• Eureka US Official Website | We work hard to make cleaning easy. - Eureka

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Eureka NEN110 Series Manual