This User Manual does not address the end user� It is intended as a source of information for the equipment or system manufacturer only, and it will tell you how to install, use and maintain your LINAK electronics� The manufacturer of the end product has the responsibility to provide a User Manual, where relevant safety information from this manual is passed on to the end user�...
LINAK, LINAK subsidiaries, or LINAK affiliates� All sales are subject to the ‘Standard Terms of Sale and Delivery for LINAK A/S’ available on LINAK websites� LINAK and the LINAK logotype are registered trademarks of LINAK A/S� All rights reserved�...
LA25 I/O User Manual | ™ Safety instructions Please read this safety information carefully� Be aware of the following three symbols throughout the user manual: Warning! Failing to follow these instructions can cause accidents resulting in serious personal injury� Recommendations Failing to follow these instructions can result in the actuator suffering damage or being ruined�...
Page 6
LA25 I/O User Manual | ™ During operation, please be aware of the following: • Listen for unusual sounds and watch out for uneven running� Stop the actuator immediately if anything unusual is observed� • Do not sideload the actuator�...
Please pay special attention to the area around the housing where parts can be trapped and cause damage to the application and actuator� In applications with high dynamic forces, LINAK recommends not using the fully extended or retracted position over a longer period of time, as this can damage the endstop system permanently�...
Page 8
LA25 I/O User Manual | ™ Mounting guidelines • The mounting pins must have the correct dimension� • The bolts and nuts must be made of a high quality steel grade (e�g� 10�8)� • No thread on the bolt inside the back fixture or the piston rod eye�...
5. Use a screwdriver to pull up the cable The torque of the cover screw is approx. 1.5 Nm • When changing the cables on a LINAK actuator, it is important that this is done carefully in order to ®...
LA25 I/O User Manual | 10 ™ Electrical installation • To ensure maximum self-locking ability, please be sure that the motor is shorted when stopped� Actuators with Integrated Controller provide this feature, as long as the actuator is powered� •...
™ LA25 I/O™ with Bluetooth ® LA25 I/O is an industrial linear actuator with Integrated Controller and various analogue/digital input and outputs� To support development, continuous improvements and troubleshooting, it also features a Bluetooth service interface� This can be used to wirelessly connect the actuator to a Windows PC and make ®...
Page 12
® tion, and has no functionality during operation� The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG Inc. and any use of such marks and logos by LINAK® is under license.
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement� The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG Inc. and any use of such marks and logos by LINAK® is under license.
Try repowering the system or initialising the actuator� If (internal error) the error cannot be solved, please contact your local LINAK office for further assistance� • Run signal To avoid unintended movement the actuator has ignored the run signal after overruled repowering�...
- If the initialisation process has fixed the internal or external error, the actuator is ready to operate in parallel again� For further assistance, please contact your local LINAK supplier� ®...
LA25 I/O User Manual | 16 ™ Specifications Motor Permanent magnet motor 12 or 24 V Cable Motor: 8 x 18 AWG PVC cable Housing The housing is made of casted aluminium, coated for outdoor use and use in harsh...
LA25 I/O User Manual | 18 ™ Speed and current curves - 12 V motor The typical values below are made with a stable power supply and an ambient temperature of 20˚C� LA25 - 12 V Speed vs Load 20 mm pitch...
LA25 I/O User Manual | 19 ™ Speed and current curves - 24 V motor The typical values below are made with a stable power supply and an ambient temperature of 20˚C� LA25 - 24 V Speed vs Load 20 mm pitch...
LA25 I/O User Manual | 20 ™ Product label for LA25 I/O™ 1. Type: 250301000000FB2A=M1L00A0000216 Describes the functionality of the product 2. Item no.: 25XXXX-XX / JXXXXX Sale and ordering code 3. Prod. Date: YYYY.MM.DD The production date describes when the product has been produced.
LA25 I/O User Manual | 21 ™ Key to symbols The following symbols are used on the LA25 I/O™ labels: Symbol Norms Approvals WEEE Directive 2002/96/EC Wheelie bin Compliance to all relevant EC directives Regulatory Compliance Mark: The Australian safety/EMC regulations...
LA25 I/O User Manual | 22 ™ LA25 ordering example 25 PPP XXX SS FF P M E I = B O R P C E F L P 0 XXX Actuator type = LA25 Spindle pitch = 3 mm...
Page 23
LA25 I/O User Manual | 23 ™ LA25 ordering example 25 PPP XXX SS FF P M E I = B O R P C E F L P 0 XXX Piston rod eye Zinc-coated steel Stainless steel = ø10�2 (0231033) = ø10�2 (0231096)
Page 24
LA25 I/O User Manual | 24 ™ LA25 ordering example 25 PPP XXX SS FF P M E I = B O R P C E F L P 0 XXX Load type = Push/Pull = Push = Pull Parallel mode...
LINAK service centre� In order to avoid the risk of malfunction, all actuator repairs must only be carried out by an authorised LINAK Service shop or repairer, as special tools and parts must be used� If a system is opened by unauthorised personel, there is a risk that it may malfunction at a later date�...
LINAK, LINAK subsidiaries, or LINAK affiliates. the same reason, LINAK cannot guarantee the correctness and actual status of imprinted information on All sales are subject to the ‘Standard Terms of Sale and Delivery for LINAK A/S’ available on LINAK websites. its products.
Need help?
Do you have a question about the LA25 I/O and is the answer not in the manual?
Questions and answers