Page 1
RZ5-PHZ5V 2020-2024 Polaris RZR Pro Phase-5 V-Spec 5 Speaker SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 1400 Watt System with JVC MR1 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 RZR Pro XP Door Panel Disassembly Amplifier Installation JVR MR1...
Page 2
WIRING DIAGRAM OF COMPLETE KIT Figure 1 Figure 1 is designed to show the installer a reference overview of the complete 5 speaker wiring diagram. Each installation section will have its own detailed wiring diagram. Description Part # Description Part # Bluetooth Media Receiver w/ 2.7”...
Page 3
PANELS AND DASH DISASSEMBLY A. Remove all the seats from the vehicle. Compress the release lever located in front of the seat base. With the release lever compressed, tilt the seat forward and remove from the vehicle. B. Using a 8mm wrench. Disconnect the negative battery cable from C.
Page 4
F. Use a panel tool to assist with the removal of the (3) trim panels. The G. Open the glove compartment. Remove the (4) T25 Torx screws and blue highlighted points represent the location of the panel clips that are (3) T40 Torx screws.
Page 5
L. Open the center console and twist to disengage the locking pins M. Remove the (2) T40 torx screws from both sides of the center console and and lift out the center console tray. lift out the rear portion of the center console. N.
Page 6
R. Rotate the fuse block counterclockwise and remove the now exposed S. Remove the (2) push pins on the passenger side front of the center push pin. console. T. Lift the shift boot to expose the (1) T40 screw for removal U.
WARRANTY INFORMATION: Please read and understand these All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or instructions completely before workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects installation to avoid possible injury, or in material or workmanship.
Page 8
AMP PLATE INSTALLATION 1. POWER INPUT - CONNECT TO B-H1587 AMP POWER HARNESS 2. AMP TURN-ON - CONNECT TO JVC MR1 AMP TURN-ON WIRE 3. TO SUBWOOFER BASS LEVEL CONTROLLER 240-PXA-SLC (SOLD SEPARATELY) 4. RCA AUDIO INPUTS (FRONT/REAR/SUB) 4. OUTPUT (FRONT) - CONNECT TO FRONT SPEAKER HARNESS 6.
Page 9
A. Remove the (5) push pins located on the plastic tray in the dash B. Extract (2) T25 screws located at the back of the plastic tray, once cavity. extracted remove the plastic tray. Set aside the screws. The plastic tray will not be used in this installation.
All SSV Works enclosures are covered by a limited lifetime warranty against defects in instructions completely before material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty installation to avoid possible injury, or against defects in material or workmanship. All SSV Works Speakers are covered by a damage to the accessory or vehicle.
Page 11
C. Place the DMR1 mounting bracket over the back of the MR1, followed by the base mounting plate. D. Place the (4) dash screws through the MR1, cover panel, DMR1 mounting bracket and thread into the base mounting plate. Do not fully tighten the screws.
Page 12
G. Once crimped, remove port cover and plug in to the busbar. H. Connect the B-HRCA3 (x3) to the JVC Front, Rear and Sub-W Line Out RCAs. I. Connect the MR1 power harness to the radio harness. J. From the backside the dash panel, fasten (4) M6 T30 torx screws and washers through the dash and into the DMR1 mounting bracket.
Page 13
JVC MR1 WIRING DIAGRAM Description Part # JVC MR1 Radio Universal FM Antenna, 55” B-H1249 JVC to SSV Radio Harness Adapter B-H2367 Pulse Connector Power Harness B-H1752 RCA Cable, Male to Male, 3 ft. (x3) B-HRCA3 Detail Description Plug in B-H1249 Universal FM Cable to the JVC radio Connect JVC MR1 radio harness to B-H2367 Crimp B-H2367 to B-H1752.
Page 14
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.
Page 15
RGB LED CONTROLLER COMMAND CENTER WIRING DIAGRAM Description Part # RGB LED Controller Rocker Switch for 230-LIT-CC 230-LIT-CC SWITCH Works RGB LED Controller Command Center RGB Extension, 2 ft. B-H2934 RGB Extension, 8 ft. B-H2934 230-LIT-CC Pulse Connector Power Harness B-H2744 RGB Front Speaker Harness, 4 ft.
Page 16
RGB LED CONTROLLER COMMAND CENTER GENERAL OPERATIONS 1. Select MODE 2. Mode/Speed 3. Favorite/Preset 4. Power On/Off 5. Color/Brightness Power On/ Off: - Press button to power unit on. Press and hold button for 2 sec. to power off. RGB ring around the knob illuminates when powered on.
Page 17
UNDER DASH SUBWOOFER ENCLOSURE PARTS LIST PARTS LIST IMAGES 230-RZ5-UD10V Enclosure Base Bracket Clamp Bracket M6x1.0x12mm x9 5. M6x1.0x40mm x2 6. M6 washers x11 7. M6 Speed Clips x2 UNDER DASH SUBWOOFER ENCLOSURE ASSEMBLY TOOLS NEEDED FOR INSTALLATION - Torx Driver T25 T30 T40 - Torx Driver T25 T30 T40 - Panel removal tools A.
Page 18
B. Slip on (2) M6 speed clips onto the specified locations of the firewall. C. From the Passenger footwell, lift the 230-RZ5-UD10V into the dash cavity. D. The top of the enclosure will tuck under the chassis cross bar. The E.
Page 19
H. Connect the subwoofer cable to the 500.1 amplifier output. G. Secure the bottom of the enclosure with the provided M6x1.0x40mm T30 screws and washers to the M6 clip nuts attached to the firewall. UNDER DASH SUBWOOFER WIRING DIAGRAM Description Part # Detail Description...
Page 20
CONNECTING AMPLIFIER POWER & GROUND CABLE TO BATTERY Battery Terminal Cable Power Wire Break Break off tab off tab A1. Remove the bottom cover of the fuse holder A2. Extract both fuse holder screws and fasten A3. Attach both the Power Wire and Battery by extracting the 2 screws.
Page 21
SPEAKER DASH POD PARTS LIST PARTS LIST IMAGES Speaker Dash Pod, Drive Side Speaker Dash Pod, Passenger Side SSV Works A-Spec Speakers (pre-mounted) 2mm Self Adhesive Speaker Gasket Driver and Passenger Side Brackets T Brackets (x2) P and D Bracket Hardware Pack, T Brackets Hardware Pack, M6x16mm #14 x .75”...
Page 22
SPEAKER DASH POD INSTALLATION TOOLS NEEDED FOR INSTALLATION - T30 Torx Driver - Phillips Screw Driver A. Start by removing the front fenders. B. Remove the screw holding the door latch panel. C. Remove the factory speaker grill by removing the (2) screws on the D.
Page 23
G. Slide up the RZR kick pod under the dash. H. Secure the T brackets of each pod to the factory bosses on the footwell using (2 each) #14x.75 phillips screws [B-HP#14-4]. I. Secure the D (driver) and P (passenger) pod brackets to the vehicle frame using (2) M6x16 screws [B-HP3503] circled above. ***Test the system for functionality before reassembling the panels*** J.
Page 24
K. Completed installation of driver and passenger side of SSV Works RZR 6.5” dash pods. L. Reinstall the front fenders.
Page 25
REAR CAGE POD PARTS LIST PARTS LIST IMAGES RZ5-DF65V Enclosures Dual Mounting Clamp Base x 2 2” Ring Clamp x 4 M6x1.0x20mm (8mm Hex (1 pair) Head) Screws & Washers x4 M6x1.0x45mm (5mm Allen M6x1.0x6mm (3mm Allen B-H2195 Rear Speaker Harness B-H1913 Speaker Extension Head) Screws &...
Page 26
C1. Place both ring mounting clamps on the cage C2. Press the clamps onto the roll cage over the using the plastic bag to prevent scratching. plastic bag. THE CLAMPS! SSV Works Tension Clamps are designed to grip tightly onto the tube.
Page 27
D. Place the cage mount pod in its final mounting location and secure E. Take the B-H2195 rear speaker harness and plug into the B-H1913 (add B-H1912 for 4 door models) rear extension harness. Plug the to the clamps using the two (2) M6 allen socket head bolts and B-H2936 RGB “Y”...
Need help?
Do you have a question about the RZ5-PHZ5V and is the answer not in the manual?
Questions and answers