Advertisement
Quick Links
SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
3
pg
Door Panel
Disassembly
7
pg
Amplifier
Installation
9
pg
Anti-Pop Circuit
Installation
11
pg
LIT-CC RGB Controller
Installation
14
pg
Subwoofer
Installation
18
pg
RGB Dash Pod
Installation
22
pg
RGB Rear Speaker Pod
Installation
RZ5-PHZ5VRC
Phase-5 V-Spec 1400 Watt 5 Speaker
RZR Pro XP
2020-2024 Polaris RZR Pro
RGB Audio Kit for Ride Command
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SSV Works RZ5-PHZ5VRC
Summary of Contents for SSV Works RZ5-PHZ5VRC
- Page 1 RZ5-PHZ5VRC 2020-2024 Polaris RZR Pro Phase-5 V-Spec 1400 Watt 5 Speaker SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 RGB Audio Kit for Ride Command www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751 RZR Pro XP Door Panel Disassembly Amplifier Installation...
- Page 2 WIRING DIAGRAM OF COMPLETE KIT Figure 1 Figure 1 is designed to show the installer a reference overview of the complete 5 speaker RGB wiring diagram. Description Part # Description Part # Kicker PXA1000.5 Amplifier SD-PXA10005 Driver/Passenger RGB/Audio “Y” Speaker Harness B-H2935 RZ5 Factory Harness Amplifier Bypass Harness B-H2591...
- Page 3 PANELS AND DASH DISASSEMBLY A. Remove all the seats from the vehicle. Compress the release lever located in front of the seat base. With the release lever compressed, tilt the seat forward and remove from the vehicle. B. Using a 8mm wrench. Disconnect the negative battery cable from C.
- Page 4 F. Use a panel tool to assist with the removal of the (3) trim panels. The G. Open the glove compartment. Remove the (4) T25 Torx screws and blue highlighted points represent the location of the panel clips that are (3) T40 Torx screws.
- Page 5 L. Open the center console and twist to disengage the locking pins M. Remove the (2) T40 torx screws from both sides of the center console and and lift out the center console tray. lift out the rear portion of the center console. N.
- Page 6 R. Rotate the fuse block counterclockwise and remove the now exposed S. Remove the (2) push pins on the passenger side front of the center push pin. console. T. Lift the shift boot to expose the (1) T40 screw for removal U.
-
Page 7: Tools Needed For Installation
WARRANTY INFORMATION: Please read and understand these All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or instructions completely before workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in installation to avoid possible injury, or material or workmanship. - Page 8 A. The factory amplifier is located under the plastic tray behind the B. Locate the 4 pin Ride Command radio subwoofer output connector radio. Unplug the factory amplifier 16 pin connector and plug it and plug it to the subwoofer adatper harness (B-H2276). to the B-H2591 RZR Pro amplifier bypass harness.
- Page 9 ANTI-POP CIRCUIT CONNECTION B. Plug the blue Amp Turn on wire of the Anti-Pop circuit to the Kicker A. Plug the Anti-POP circuit (B-H2917) to a unused Pulse connector amplifier amp turn-on wire. port on the busbar. To vehicle factory bussbar Pulse connector To Kicker Amp Blue Turn-On Wire...
- Page 10 AMPLIFIER WIRING DIAGRAM Not Used Description Part # Detail Description RZ5 Subwoofer Adapter Harness B-H2591 Plug RZ5 Subwoofer Adapter Harness to 4 Pin to RCA Adapter (B-H3545) RZ5 Factory Harness Amplifier Bypass Harness B-H2276 Plug Front Output to 4 Pin to RCA Adapter (B-H3543) RZ5 Amplifier Anti-POP Circuit B-H2917 Plug Rear Output to 4 Pin to RCA Adapter (B-H3543)
- Page 11 WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.
- Page 12 RGB LED CONTROLLER COMMAND CENTER WIRING DIAGRAM Description Part # RGB LED Controller Rocker Switch for 230-LIT-CC 230-LIT-CC SWITCH Works RGB LED Controller Command Center RGB Extension, 2 ft. B-H2934 RGB Extension, 8 ft. B-H2934 230-LIT-CC Pulse Connector Power Harness B-H2744 RGB Front Speaker Harness, 4 ft.
- Page 13 RGB LED CONTROLLER COMMAND CENTER GENERAL OPERATIONS 1. Select MODE 2. Mode/Speed 3. Favorite/Preset 4. Power On/Off 5. Color/Brightness Power On/ Off: - Press button to power unit on. Press and hold button for 2 sec. to power off. RGB ring around the knob illuminates when powered on.
- Page 14 UNDER DASH SUBWOOFER ENCLOSURE PARTS LIST PARTS LIST IMAGES 230-RZ5-UD10V Enclosure Base Bracket Clamp Bracket M6x1.0x12mm x9 M6x1.0x40mm x2 M6 washers x11 M6 Speed Clips x2 UNDER DASH SUBWOOFER ENCLOSURE ASSEMBLY TOOLS NEEDED FOR INSTALLATION - Torx Driver T25 T30 T40 - Torx Driver T25 T30 T40 - Panel removal tools A.
- Page 15 B. Slip on (2) M6 speed clips onto the specified locations of the firewall. C. From the Passenger footwell, lift the 230-RZ5-UD10V into the dash cavity. D. The top of the enclosure will tuck under the chassis cross bar. The E.
- Page 16 H. Connect the subwoofer cable to the 500.1 amplifier output. G. Secure the bottom of the enclosure with the provided M6x1.0x40mm T30 screws and washers to the M6 clip nuts attached to the firewall. UNDER DASH SUBWOOFER WIRING DIAGRAM Description Part # Detail Description...
- Page 17 CONNECTING AMPLIFIER POWER & GROUND CABLE TO BATTERY Battery Terminal Cable Power Wire Break Break off tab off tab A1. Remove the bottom cover of the fuse holder A2. Extract both fuse holder screws and fasten A3. Attach both the Power Wire and Battery by extracting the 2 screws.
- Page 18 SPEAKER DASH POD PARTS LIST PARTS LIST IMAGES Speaker Dash Pod, Drive Side Speaker Dash Pod, Passenger Side SSV Works V-Spec Speakers (pre-mounted) 2mm Self Adhesive Speaker Gasket Driver and Passenger Side Brackets T Brackets (x2) P and D Bracket Hardware Pack, T Brackets Hardware Pack, M6x16mm #14 x .75”...
- Page 19 SPEAKER DASH POD INSTALLATION TOOLS NEEDED FOR INSTALLATION - T30 Torx Driver - Phillips Screw Driver A. Start by removing the front fenders. B. Remove the screw holding the door latch panel. C. Remove the factory speaker grill by removing the (2) screws on the D.
- Page 20 G. Plug the B-H3601 Tweeter Pod Expansion harness to B-H2935 H. Plug the 2 Pin connector of B-H3601 to the factory tweeter Front RGB/Audio speaker harness. connector. Factory Tweeter Retention Wiring Connection DETAIL "B" DETAIL "A" DETAIL "C" DETAIL "D" DETAIL "E"...
- Page 21 ***Test the system for functionality before reassembling the panels*** L. Reinstall the factory driver and passenger side speaker grill using the factory screws. Reinstall the front fenders. M. Completed installation of driver and passenger side of SSV Works RZR 6.5” dash pods.
- Page 22 REAR CAGE POD PARTS LIST PARTS LIST IMAGES RZ5-DF65V Enclosures Dual Mounting Clamp Base x 2 2” Ring Clamp x 4 M6x1.0x20mm (8mm Hex (1 pair) Head) Screws & Washers x4 M6x1.0x45mm (5mm Allen M6x1.0x6mm (3mm Allen B-H2195 Rear Speaker Harness B-H1913 Speaker Extension Head) Screws &...
-
Page 23: Installation Notes
C1. Place both ring mounting clamps on the cage C2. Press the clamps onto the roll cage over the using the plastic bag to prevent scratching. plastic bag. THE CLAMPS! SSV Works Tension Clamps are designed to grip tightly onto the tube. - Page 24 E. Take the B-H2195 rear speaker harness and plug into the B-H1913 D. Place the cage mount pod in its final mounting location and secure to the clamps using the two (2) M6 allen socket head bolts and (add B-H1912 for 4 door models) rear extension harness. Plug the B-H2936 RGB “Y”...
- Page 25 Plug the B-H2936 RGB Rear “Y” Harness to the Left and Right Cage Pods Connect B-H1913 to B-H2195 (for 2 door models) Plug the B-H2195 to the Left and Right Cage Pods © 2024 SSV Works, Camarillo, CA 93012 RZ5-PHZ5VRC Rev. A 12-4-24...
Need help?
Do you have a question about the RZ5-PHZ5VRC and is the answer not in the manual?
Questions and answers