Download Print this page
Omnitron Systems RuggedNet 10GMG/Si User Manual

Omnitron Systems RuggedNet 10GMG/Si User Manual

Unmanaged multi-gigabit/multi-rate 10gigabit ethernet switch

Advertisement

Quick Links

General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
, miConverter
, NetOutlook
, OmniLight
,
©
TM
®
©
®
®
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
, OST
and
®
®
TM
TM
the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
RuggedNet
10GMG/Si
®
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Unmanaged Multi-Gigabit/Multi-Rate
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
10Gigabit Ethernet Switch
material and workmanship for a period of two (2) years from the date of shipment.
A five (5) year warranty may be obtained by the original purchaser by registering
this product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
User Manual
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
Page 2

Advertisement

loading
Need help?

Need help?

Do you have a question about the RuggedNet 10GMG/Si and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems RuggedNet 10GMG/Si

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2 Product Overview Directive) of the European Community directive 2012/19/EU on waste electrical and The RuggedNet 10GMG/Si are unmanaged industrial multi-gigabit Ethernet switches electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ EU, for electrical and electronic equipment sold in the EU after July 2019. Such featuring one 1/10G SFP/SFP+ or multi-gigabit/multi-rate RJ-45 uplink port with two multi-gigabit/multi-rate RJ-45 and two 10/100/1000 RJ-45 downlink/access ports.
  • Page 3 Installation Procedure SW1: Switch Mode - “Normal/Directed Switch” 1) Configure DIP-switches The module supports Normal or Directed Switch Mode. 2) Installing the Module The modes are described with MAC learning enabled. When MAC learning is disabled, unicast packets are forwarded to all ports. 3) Apply DC Power Switch Mode 4) Connect Cables...
  • Page 4 SW8: L2CP - “L2CP Tunnel/Discard” 3) Apply DC Power When this DIP-switch is in the LEFT “L2CP Tunnel” position (factory default), all This module is intended for installation in restricted access areas. (“Les matériels L2CP frames will be tunneled through the module. When this DIP-switch is in the sont destinés à...
  • Page 5 WARNING!!! NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE POWER SUPPLY. OPENING THE CHASSIS MAY CAUSE SERIOUS INJURY OR DEATH. THERE ARE NO USER REPLACEABLE OR SERVICEABLE PARTS IN THIS UNIT. Make sure to disconnect both power connectors and the ground cables before removing the equipment.
  • Page 6 4) Verify Operation 10/100/1000 RJ-45 Port LED Indicators Verify the module is operational by viewing the LED indicators. Legend Indicator Description Power LED Indicators Port not linked Legend Indicator Description Link Green - ON Port linked at the speed indicated by the Rate LED Power not being supplied by Power Supply A Green - Blinking at 10Hz Port is linked and transmitting or receiving data...
  • Page 7 Specifications Safety: UL 62368-1, UL 60950-1, RuggedNet ® 10GMG/Si IEC 62368-1, Description IEC 60950-1, Unmanaged 10Gigabit Multi-Gigabit/Multi-Rate Ethernet Switch EN 62368-1, Standard Compliances IEEE 802.3 EN 60950-1, CAN/CSA C22.2 No. 62368-1-14, Environmental REACH, RoHS and WEEE CAN/CSA C22.2 No. 60950-1, CE Mark, UKCA Frame Size Up to 10,240 bytes...
  • Page 8 Customer Support Information If you encounter problems while installing this product, contact Omnitron Technical Support: Phone: (949) 250-6510 Fax: (949) 250-6514 Address: Omnitron Systems Technology, Inc. 38 Tesla Irvine, CA 92618, USA Email: support@omnitron-systems.com URL: www.omnitron-systems.com Intentionally Left Blank 040-09660-001B...