Omnitron Systems RuggedNet GL User Manual

Unmanaged industrial single pair ethernet switch

Advertisement

RuggedNet
GL/Si
®
Unmanaged Industrial
Single Pair Ethernet Switch
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
®
TM
OmniConverter
, RuggedNet
, Omnitron
®
®
OST
and the Omnitron logo.
TM
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
material and workmanship for a period of two (2) years from the date of shipment.
A five (5) year warranty may be obtained by the original purchaser by registering
this product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
®
®
, Omnitron Systems Technology, Inc.
®
Page 2
,
®
,
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RuggedNet GL and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems RuggedNet GL

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Product Overview

    Product Overview Directive) of the European Community directive 2012/19/EU on waste electrical and The RuggedNet GL/Si is an unmanaged Industrial gigabit Ethernet switch that electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ EU, for electrical and electronic equipment sold in the EU after July 2019. Such features copper or fiber uplink ports and four single-pair 10BASE-T1L Ethernet user ports.
  • Page 3 The illustrations below show fiber uplink ports. The switch is available with copper uplink ports and operate in the same manner as shown below. DIP-switches are located on the top of the RuggedNet GL/Si. The DIP-switches are used to configure modes of operation and networking features.
  • Page 4: Installing The Module

    When configured for Dual Device Mode and Directed Switch Mode, the traffic from SW5: MAC Learning - “ON/OFF” ports P1 and P2 is only forwarded to uplink port F1 and ports P3 and P4 are only When this DIP-switch is in the LEFT “ON” position (factory default), all ports on forwarded to uplink port F2.
  • Page 5: Apply Dc Power

    3) Apply DC Power This module is intended for installation in restricted access areas. (“Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT”). A restricted access area can be accessed only through the use of a special key, or other means of security.
  • Page 6: Connect Cables

    5) Verify Operation WARNING!!! Verify the switch is operational by viewing the LED indicators. NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE POWER SUPPLY. OPENING THE Power LED Indicators CHASSIS MAY CAUSE SERIOUS INJURY OR DEATH. Legend Indicator Description THERE ARE NO USER REPLACEABLE OR SERVICEABLE PARTS IN THIS UNIT.
  • Page 7: Specifications

    Specifications RuggedNet GL/Si ® Description 10T/T1L to 100/1000 Fiber or 10/100/1000 Copper Uplinks Safety: UL 62368-1, UL 60950-1, Unmanaged Industrial Ethernet Switch IEC 62368-1, IEC 60950-1, EN 62368-1, EN 60950-1, Standard Compliances IEEE 802.3, 802.3cg CAN/CSA C22.2 No. 62368-1-14 and No. 60950-1 CE Mark Environmental REACH, RoHS and WEEE...
  • Page 8 Mechanical Customer Support Information If you encounter problems while installing this product, contact Omnitron Technical Support: Phone: (949) 250-6510 Fax: (949) 250-6514 Address: Omnitron Systems Technology, Inc. 38 Tesla Irvine, CA 92618, USA Email: support@omnitron-systems.com URL: www.omnitron-systems.com 040-02913-001A 4/25 Page 15...

This manual is also suitable for:

Ruggednet si

Table of Contents