Omnitron Systems OmniConverter G/M Quick Start Manual

Omnitron Systems OmniConverter G/M Quick Start Manual

Managed 6 and 10 port gigabit ethernet switch

Advertisement

Quick Links

OmniConverter
Managed
6 and 10 Port Gigabit Ethernet Switch
Quick Start Guide
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
G/M
®
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, HybridNID
TM
TM
OmniLight
, OmniConverter
, RuggedNet
®
®
OST
and the Omnitron logo.
TM
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This network product and the included AC/DC power adapter are warranted to the
original purchaser (Buyer) against defects in material and workmanship for a period
of two (2) years from the date of shipment. The warranty for the network product
(excluding the AC/DC power adapter) can be extended to five (5) years by registering
the product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, iConverter
, miConverter
, NetOutlook
®
®
TM
, Omnitron Systems Technology, Inc.
®
Page 2
,
®
,
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniConverter G/M and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems OmniConverter G/M

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Product Overview

    Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ The OmniConverter G/M is a compact gigabit Ethernet switch that features fiber or EU, for electrical and electronic equipment sold in the EU after July 2019. Such copper uplink ports and four or eight 10/100/1000 RJ-45 copper user ports.
  • Page 3: Installation Procedure

    3) Apply Power 4) Connect Cables 5) Verify Operation 1) Configure DIP-switches DIP-switches are located on the side of the OmniConverter G/M. The DIP-switches are used to configure modes of operation and networking features. DIP-switch Bank Locations Front Panel Layout The table below provides a description of each DIP-switch position and function.
  • Page 4: Sw1 And Sw2: Mode Of Operation

    SW1 and SW2: Mode of Operation The module supports Switch, Directed Switch and Dual Device modes. The modes are described with MAC learning enabled. When MAC learning is disabled, unicast packets are forwarded to all ports. 1 Uplink Port 2 Uplink Ports Function DOWN DOWN...
  • Page 5 Dual Device Mode When configured for Uplink Redundant Mode “no return to primary”, the uplink ports operate as redundant links. A fault on the primary Port F1, will cause a fail Dual Device Mode is only supported on models with two uplink ports. over to the secondary Port F2 within 50msec.
  • Page 6: Installing The Module

    2) Installing the Module DC Power This module is intended for installation in restricted access areas. (“Les matériels Wall Mounting sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT”). The wall mounting height of the module should be less than or equal to 2 meters A restricted access area can be accessed only through the use of a special key, or (6.6 feet) from the floor.
  • Page 7 Connect the power wires to the circuit breaker and switch the circuit breaker ON. If any module are installed, the Power LED will indicate the presence of power. WARNING REGARDING EARTHING GROUND: This equipment shall be connected to the DC supply During the installation, ensure that the ground potentials are maintained throughout system earthing electrode conductor or to a bonding the system connections.
  • Page 8: Verify Operation

    5) Verify Operation RJ-45 User Ports LED Indicators Verify the module is operational by viewing the LED indicators. Legend Indicator Description Power No link LED Indicators Green - ON Port linked at 100Mbps Legend Indicator Description Green - Blinking at 10Hz Port data activity at 100Mbps Unit not powered Amber -ON...
  • Page 9: Specifications

    Specifications Safety: UL 60950-1, UL-62368-1, OmniConverter ® IEC 62368:2014 /A11:2017, IEC 60950-1:2005+A1:2009, Description 10/100/1000BASE-T with Gigabit Fiber or Copper Uplinks EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, Managed 6 or 10 Port Gigabit Ethernet Switch CAN/CSA C22.2 No. 60950-1, IEEE 802.3, CAN/CSA C22.2 No. 62368-1-14, CE Mark IEEE 802.1Q, IEEE 802.1ad, IEEE 802.1ab, IEEE 802.1w, IEEE 802.1ax, Standard Compliances...
  • Page 10: Customer Support Information

    Customer Support Information If you encounter problems while installing this product, contact Omnitron Technical Support: Phone: (949) 250-6510 Fax: (949) 250-6514 Address: Omnitron Systems Technology, Inc. 38 Tesla Irvine, CA 92618, USA Email: support@omnitron-systems.com URL: www.omnitron-systems.com Intentionally Left Blank 040-02820-001C...

Table of Contents