Omnitron Systems RuggedNet GHPoE/Si User Manual

Omnitron Systems RuggedNet GHPoE/Si User Manual

Unmanaged 6 port 60w pre-bt poe and 60/100w ieee 802.3bt gigabit switches

Advertisement

Quick Links

RuggedNet
®
GHPoE/Si and GHPoEBT/Si
Unmanaged 6 Port
60W Pre-BT PoE and 60/100W IEEE 802.3bt
Gigabit Switches
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
TM
TM
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
®
®
the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
material and workmanship for a period of two (2) years from the date of shipment.
A five (5) year warranty may be obtained by the original purchaser by registering
this product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
TM
®
, OST
TM
Page 2
,
®
and
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RuggedNet GHPoE/Si and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems RuggedNet GHPoE/Si

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.: RuggedNet ®...
  • Page 2: Product Overview

    Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ The RuggedNet GHPoE/Si and GHPoEBT/Si are industrial unmanaged Ethernet EU, for electrical and electronic equipment sold in the EU after July 2019. Such...
  • Page 3: Installation Procedure

    The table below provides a description of each DIP-switch position and function. Switch 1 Uplink Port 2 Uplink Ports Reserved Device Mode Switch Mode Reserved Uplink Redundancy Reserved MAC Learning Forced PoE Power L2CP Front Panel Layout PoE Reset Reset Button DIP-switch Definitions A Reset Button is available on the front of the switch to restore the switch to factory SW1 and SW2: Mode of Operation...
  • Page 4 For models with two uplink ports (copper or fiber), the data traffic on the additional Dual Device Mode uplink port (F2) is also forwarded to port F1. Dual Device Mode is only supported on models with two uplink ports. When configured for Dual Device Mode, the module is configured as two logically independent Layer 2 switches.
  • Page 5 SW3 and SW4: Uplink Redundancy SW5: MAC Learning - “MAC Learning/Off” Uplink redundancy mode is only supported on models with two uplink ports. When this DIP-switch is in the LEFT “MAC Learning” position (factory default), all ports on the module will learn the source MAC address of each received packet and The modes are described with MAC learning enabled.
  • Page 6: Installing The Module

    2) Installing the Module The module can be wall or rack mounted using the optional Wall Mount Plate WARNING REGARDING EARTHING GROUND: This equipment shall be connected to the DC supply (8260-3). Refer to the Wall Mount Plate user manual (040-08260-301x) for the system earthing electrode conductor or to a bonding proper installation guidelines.
  • Page 7: Connect Cables

    4) Connect Cables When using SFP models, insert the SFP fiber transceiver into the SFP receptacle on the front of the module (see the SFP Data Sheet 091-17000-001 for supported Gigabit transceivers). NOTE: The release latch of the SFP fiber transceiver must be in the closed (up) position before insertion.
  • Page 8: Verify Operation

    5) Verify Operation RJ-45 User Ports LED Indicators Verify the module is operational by viewing the LED indicators. Legend Indicator Description Power No link LED Indicators Amber -ON Port linked at 10Mbps Half-duplex Legend Indicator Description Amber - Blinking at 10Hz Port data activity at 10Mbps Half-duplex Unit not powered (100+1000) Green - ON...
  • Page 9: Specifications

    Specifications RuggedNet GHPoEBT/Si (60/100W BT) ® Description 10/100/1000BASE-T with Gigabit Fiber or Copper Uplinks RuggedNet GHPoE/Si (60W Pre-BT) ® Ruggedized Unmanaged IEEE 802.3bt PoE Ethernet Switch Description 10/100/1000BASE-T with Gigabit Fiber or Copper Uplinks IEEE 802.3, Ruggedized Unmanaged High-Power PoE Ethernet Switch IEEE 802.3af (15.40 watts max), Standard Compliances IEEE 802.3at (30 watts max)
  • Page 10: Customer Support Information

    CE Mark Fax: (949) 250-6514 EMC: EN 55032/EN 55024 CE Emissions/Immunity, IEC 61000-6-4 Industrial Emissions, Address: Omnitron Systems Technology, Inc. IEC 61000-6-2 Industrial Immunity Regulatory Compliances 38 Tesla EMI: CISPR 32, FCC 47 Part 15 Subpart B Class A Irvine, CA 92618, USA EMS: IEC 61000-4-2 ESD: Contact: 4 kV;...

This manual is also suitable for:

Ruggednet ghpoebt/si

Table of Contents