Omnitron Systems OmniConverter 10GMGPoEBT/M User Manual

Omnitron Systems OmniConverter 10GMGPoEBT/M User Manual

Managed multi-gigabit/multi-rate 60/100w poe 10gigabit ethernet switch

Advertisement

OmniConverter
Managed Multi-Gigabit/Multi-Rate
60/100W PoE 10Gigabit Ethernet Switch
User Manual
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
10GMGPoEBT/M
®
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
TM
TM
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
®
®
the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This network product and the included AC/DC power adapter are warranted to the
original purchaser (Buyer) against defects in material and workmanship for a period
of two (2) years from the date of shipment. The warranty for the network product
(excluding the AC/DC power adapter) can be extended to five (5) years by registering
the product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
at Buyer's expense. Omnitron will pay the shipping charge to return the product
to Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
, miConverter
, NetOutlook
, OmniLight
®
TM
®
, OST
TM
Page 2
,
®
and
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniConverter 10GMGPoEBT/M and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems OmniConverter 10GMGPoEBT/M

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Product Overview

    Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ The OmniConverter 10GMGPoEBT/M are managed multi-gigabit Ethernet switches EU, for electrical and electronic equipment sold in the EU after July 2019. Such...
  • Page 3: Installation Procedure

    The table below provides a description of each DIP-switch position and function. Serial Console Port To configure the module using the serial port, attach a DB-9 serial (RS-232) Switch Position Legend Function equipped computer with terminal emulation software such as Procomm or Putty DOWN Normal Normal Switch Mode is Enabled (factory default)
  • Page 4 SW2: PSE Reset - “Off/PoE Reset” the address so packets destined for the stored addresses can be forwarded to the appropriate port on the module. When the DIP-switch is in the UP “MAC Learning” The module can be configured to disable (reset) the PoE output power for 5 seconds position, learning is turned off and all received unicast packets are forwarded to after a loss of receive link on the uplink port.
  • Page 5: Din-Rail Mounting

    DIN-Rail Mounting The module can be DIN-rail mounted using the optional DIN-Rail Mounting Clips (8251-1). Refer to the DIN-Rail Mounting Clips user manual (040-08251-001x) for the proper installation guidelines. 3) Apply Power AC Power Secure the ground wire to the ground screw. See the figure below for the location WARNING: Only a DC power source that complies with of the grounding screws.
  • Page 6: Verify Operation

    WARNING: Note the wire colors used in making the positive, negative and 4) Verify Operation ground connections. Use the same color assignment for the connection at Verify the module is operational by viewing the LED indicators. the circuit breaker. Power LED Indicators Connect the power wires to the circuit breaker and switch the circuit breaker ON.
  • Page 7: Specifications

    Specifications 10/100/1000 RJ-45 Port LED Indicators Legend Indicator Description OmniConverter 10GMGPoEBT/M ® Description Managed IEEE 802.3bt 10Gigabit Multi-Gigabit/Multi-Rate Ethernet Port not linked Switch Link Green - ON Port linked at the speed indicated by the Rate LED IEEE 802.3, 802.3bz, Green - Blinking at 10Hz Port is linked and transmitting or receiving data Standard Compliances...
  • Page 8: Customer Support Information

    EN 60950-1, CAN/CSA C22.2 No. 62368-1-14, Fax: (949) 250-6514 CAN/CSA C22.2 No. 60950-1, CE Mark, UKCA Address: Omnitron Systems Technology, Inc. EMC: EN 55032/24 CE Emissions/Immunity, IEC 61000-6-4 Industrial Emissions, 38 Tesla IEC 61000-6-2 Industrial Immunity Irvine, CA 92618, USA...

Table of Contents