Huawei LUNA2000-200KTL-H1 Quick Manual
Smart power control system
Hide thumbs
Also See for LUNA2000-200KTL-H1:
- User manual (105 pages) ,
- Quick manual (2 pages) ,
- Quick manual (82 pages)
Subscribe to Our Youtube Channel
Related Manuals for Huawei LUNA2000-200KTL-H1
Summary of Contents for Huawei LUNA2000-200KTL-H1
- Page 1 LUNA2000-200KTL-H1 Smart Power Control System Quick Guide Issue: 05 Part Number: 31500HHP Date: 2023-07-25 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 • During operations, use dedicated insulated tools and wear personal protective equipment, such as protective clothing, insulated shoes, goggles, safety helmets, and insulated gloves. Overview Smart Power Control System Appearance (also referred to as Smart PCS) Copyright © Huawei Technologies Co., Ltd. 2023. All rights reserved.
- Page 3 (1) AC maintenance compartment (2) Communications cable hole (FE) (3) Panel (4) DC maintenance compartment (5) LED indicator (6) Security Torx wrench (7) Protective ground point (8) Communications cable hole (COM) (9) AC power cable hole (10) USB port (USB) (11) DC power cable hole Dimensions and Weight Smart PCS: <...
- Page 4 Installation Requirements Installation Angle Installation Clearance (Support-mounting and Wall-mounting) • Support-mounting and wall-mounting: ≥ 600 mm, 600– 730 mm of clearance is recommended underneath. • Not applicable to the DCBOX installation scenario Installation Process...
- Page 5 Installing the Smart PCS Support-mounting and Wall-mounting Avoid drilling holes into the water pipes or power cables buried in the wall. • To avoid inhaling dust and to prevent dust from falling into your eyes, ensure that safety goggles and a dust mask are worn when drilling holes. •...
- Page 6 • Tighten the lifting handle (ensure that the steel washer of the lifting handle is closely attached to the module). • If the stud of the lifting handle is bent, replace the lifting handle in time. Lifting handle screw Mounting bracket hole screw holes Hoisting...
- Page 7 4. Install the Smart PCS to the mounting bracket. Installing the Smart PCSs on the DCBOX Do not stand on the top of the DCBOX. 1. Before installing the Smart PCS, unbind the DC power cables preinstalled on the top of the DCBOX. 2.
- Page 8 3. Install the first Smart PCS. The M8 screws and torx wrench are delivered with the DCBOX. 4. Install the remaining Smart PCSs and the fasteners delivered with the DCBOX.
- Page 9 Electrical Connections • Remove the rubber rings according to the cable diameter range, and ensure that the crimping module is not damaged. Otherwise, the device may fail to offer the expected level of protection. • Ensure that the AC/DC power cables are connected securely. Otherwise, the Smart PCS may fail to operate, or become overheated during operation due to an unreliable connection, which will damage the terminal block.
- Page 10 Cable Type Conductor Outer Source Cross- Diameter Sectional Area Range Communications FE communications cable: CAT 0.2 mm 4.5–7.5 The cable delivered cable 5E outdoor shielded network with the device is 1.2 cable (internal resistance ≤ 1 m long. You can also ohm/10 m) and the shielded prepare a cable RJ45 connector...
- Page 11 Opening the AC/DC Maintenance Compartment Door • Do not open the panel of the Smart PCS. • Before opening the maintenance compartment door of the Smart PCS, turn off the external switches on the AC and DC sides. • Do not open the maintenance compartment door on rainy or snowy days. The following describes how to open the maintenance compartment door on the DC side.
- Page 12 Connecting DC Power Cables Before connecting DC power cables, check and label the polarity of the cables. Single-core Cable Connection Method In the DCBOX installation scenario, use the DC power cables of the corresponding Smart PCS installation position on the DCBOX.
- Page 13 Two-core Cable Connection Method Connecting AC Power Cables Single-core Cable Connection Method...
- Page 14 Three-core Cable Connection Method • It is recommended that the stripped length of the L2 wire be 15 mm shorter than that of the L1 or L3 wire. • If a cable has a jacket, ensure that the jacket is in the maintenance compartment.
- Page 15 Connecting FE Communications Cables • If the SmartACU2000D-D-06 is used, the Smart PCS is connected to the SmartACU through FE communications cables. Ensure that both ends are connected to G2–G7 of the SmartACU (SWITCH02). A maximum of three ring networks can be connected. •...
- Page 16 Connected to SmartACU2000D-D-00 1. Prepare the FE communications cables. (1) White-and-orange (2) Orange (3) White-and-green (4) Blue (5) White-and-blue (6) Green (7) White-and-brown (8) Brown 2. Connect the FE communications cables.
- Page 17 3. When multiple Smart PCSs are connected in parallel, bind the FE communications cables connecting to the Smart Array Controller (SACU) or SmartModule at proper positions near the ports. If Smart PCSs are installed on the DCBOX, bind the cables as shown in the following figure.
- Page 18 Closing the AC/DC Maintenance Compartment Door The following describes how to close the maintenance compartment door on the DC side. The procedure for closing the maintenance compartment door on the AC side is the same. Checking Before Power-On Check Item The Smart PCS is not deformed or damaged.
- Page 19 Check Item The DC maintenance compartment door is closed and the screws on the door are tightened. The waterproof plugs on the unused USB, COM, and FE ports are secured. Power-On Indicator Status (Blinking Fast: On for 0.2s and Off Category Description for 0.2s;...
- Page 20 4. Observe the LED indicators to check the running status of the Smart PCS. How Do I Download the SUN2000 App? • Method 1: Search for SUN2000 in Huawei AppGallery. • Method 2: Scan one of the QR codes below.
- Page 21 Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China https://digitalpower.huawei.com...
Need help?
Do you have a question about the LUNA2000-200KTL-H1 and is the answer not in the manual?
Questions and answers