Related Manuals for HARVEY ALPHA HW110LC-36Pro
Summary of Contents for HARVEY ALPHA HW110LC-36Pro
- Page 1 Revision C 2024.06 INSTRUCTION MANUAL Original Instructions 10″ 2HP Cabinet Table Saw with BIG EYE Fence MODEL:HW110LC-36Pro...
- Page 3 Contents 1. Foreword ..........................1 2. Warranty Information ......................1 3. Machine Description ......................2 3.1 Technical Parameters ....................2 3.2 Features Identification ....................5 3.3 Optional Equipments ...................... 5 3.4 Intended Use ........................6 3.5 Requirements of Electrical Power .................. 6 4.
- Page 4 1. Foreword 2. Warranty Information This manual contains basic information for qualified Limited Warranty operating staff and describes the surroundings and Two years. using ways of the machine for those it is intended. Proof of Purchase It contains also all necessary information for a Please keep your dated proof of purchase for correct and safe operating.
- Page 5 3. Machine Description 3.1 Technical Parameters For North American Market： ITEM HW110LC-36Pro Weight 400lbs 69.3” x 41.3” x 48.3” Product Length/Width/Height Dimensions (1760x1050x x1225 mm) Footprint 20-1/4” x 19-5/8”(514x498 mm) Switch type Magnetic with Thermal Overload Protection Switch Standard UL62841 Type TEFC, Capacitor Start, Induction 2.0 HP, 115 V, 1 PH, 16 A...
- Page 6 For European Market： ITEM HW110LC-36Pro Weight 181.5 kg Product Dimensions Length/Width/Height 1760x1050x 1225 mm Footprint 514x498mm Switch type Magnetic with Thermal Overload Protection Switch Standard Type TEFC, Capacitor Start, Induction Horsepower, Voltage, Phase, Amps 1.65 kW, 220 V, 1 PH, 10 A Motor Speed 2900 RPM...
- Page 7 For Asian Market： ITEM HW110LC-36Pro Weight 181.5 kg Product Dimensions Length/Width/Height 1760x1050x 1225 mm Footprint 514x498 mm Switch type Magnetic with Thermal Overload Protection Switch Standard Type TEFC, Capacitor Start, Induction Horsepower, Voltage, Phase, Amps 1.65 kW, 220 V, 1 PH, 10 A Motor Speed 2900 RPM...
- Page 8 3.2 Features Identification 3.3 Optional Equipment Refer to Fig. 1. Sliding table Model: ST-1500 Fig. 1-1 Universal Overhead Guard Fig. 1 Model: S-12S Left Extension Wing Miter Gauge Main Table Blade Guard Fig. 1-2 Right Extension Wing Fence Assembly On/Off Switch Motor Cover Over Arm Dust Collection (system) Blade Elevation Hand Wheel...
- Page 9 3.4 Intended Use This table saw and the workpiece guide equipment supplied with it are intended to be used exclusively The machine is prohibited to be used in a for the following purposes: potentially explosive atmosphere! Laminated and unlaminated board materials (e.g. ●...
- Page 10 4. Safety Regulations 14. DISCONNECT MACHINES. Before servicing, when changing accessories or attachments; 4.1 General Safety Instructions 15. AVOID ACCIDENTAL STARTING. 1. KNOW YOUR MACHINE. Make sure the switch is in the “OFF” position Read and understand the owner’s manual and before plugging in;...
- Page 11 4.3 Residual Risks 5. STAND TO THE SIDE WHEN FEEDING MATERIAL. Take precautions to reduce the hazard of Never stand or have any part of your body in line inhalation of harmful dust (e.g. wearing a dust with the path of the saw blade; mask);...
- Page 12 5. Installation of the Machine 5.2 Unpacking Your machine was carefully packaged for safe transportation. Remove the packaging materials 5.1 Transportation of Machines from around your machine and inspect it. If you 5.1.1 Transportation and store discover that the machine is damaged, please This machine has been well packaged and rust immediately call Customer Service for advice.
- Page 13 5.3 Contents The product is packed by four individual boxes as follows: Main machine box contents: (Fig. 5-1-----Fig. 5-4) A. Main table saw unit……..………..………1 B. Motor cover……….……..………..………1 C. Left extension wing……..………………1 D. Extension table (width 365 mm)………1 Fig. 5-1 E. Saw blade…………………………………1 F.
- Page 14 Fence box contents:(Fig. 5-5) Over arm box contents:(Fig. 5-7) A. Over arm..…………..……………..……1 Please refer to the Instruction Manual of BIG EYE B. Flexible hose (length 0.6 m)…………...1 RIP FENCE SYSTEM for the list. C. Flexible hose (length 1 m)………………1 D. Bracket…………………………………..2 Note：...
- Page 15 5.4 Installation 5.4.1 Remove the pallet Before beginning assembly, take note of the The machine is fixed on the pallet by M8 hex bolts. following precautions and suggestions: Before installing, please take off the accessories on the pallet and in the cabinet. Then move the FLOOR: Make certain that the floor is a level machine out after removing the set bolts under the surface.
- Page 16 sand paper if necessary to clean up the edges; 5.4.7 Install the blade 3. Attach the wings to the main table by using the 1. Remove the table insert; screws removed in step 1; 2. Rise the arbor all the way up and set the blade 4.
- Page 17 American market. Fig.17(B) shows the blade guard meeting the CE standard. For different markets, the machine is equipped with different blade guards, please refer to the chapter “3. Machine Description” for detailed information. Fig.18-1 Fig. 17 Check if the saw blade is tightened before operating the machine.
- Page 18 Requirements for the dust collector: 5.4.12 Electrical installation 1. Required air flow: 470 CFM (800 m³/h). 2. Ensure pressure drop of each dust collector outlet carrying air current speed: 1100Pa Wiring should only be done by professional 3. Dry chips: 3937 FPM (20 m/s). electricians.
- Page 19 ELECTRICAL DIAGRAM 2 HP, 60 Hz, 115/230 V, 1 PH 115 V Wiring Diagram 230 V Wiring Diagram Remark: 1. The colour of single core may differ with the illustration above in different areas. 2. Single-phase power supply range: 110-120V or 200-240 V. The machine is pre-wired with the voltage of 115V.
- Page 20 1.65 kW, 50 Hz, 230 V, 1 PH Remark: 1.The colour of single core may differ with the illustration above in different areas. 2.Single-phase power supply range: 200-240V. 3. Meeting the CE standard, this electrical diagram is designed for European and Asian areas. 4.
- Page 21 Rewiring for 230V Power (Note: This chapter is only available for the table saw with dual voltages.) The power must be disconnected before any wiring operations! This table saw can be used for 115V or 230V power. Fig. 21 It comes from the factory pre-wired for 115V, so if you want to use it for 230V, you need to take off the 2.
- Page 22 6. Adjustment Before operation, Please make adjustments as followings: 6.1 Adjusting the Rip Fence Before using the rip fence, the parallelism and perpendicularity must be aligned correctly. Please refer to chapter 5.4.4 Install the rail & fence. Fig. 24 6.2 Aligning the Table T-slot Parallel with 6.3 Adjusting the 45°...
- Page 23 greater than the saw blade plate. As shown in Fig. 6.4 Aligning the Riving Knife with Blade The riving knife must be aligned with the blade. If not properly aligned, the riving knife will force the workpiece sideways during the cut, increasing the risk of kickback.
- Page 24 7.2 Blade Elevation and Tilting Adjustment 7. Operations Loosen the lock To adjust the blade elevation : 7.1 Electrical Operation knob (C) as shown in Fig. 32 and turn the elevation Two types of the switches are alternative for hand wheel (D). When the desired height is your machine, the actual object shall prevail.
- Page 25 7.3 Crosscutting 7.4 Ripping "Crosscutting" means cutting across the grain of "Ripping" means cutting with the grain of a natural a natural wood workpiece. In other man-made wood workpiece. In other man-made materials materials, such as MDF or plywood, crosscutting such as MDF or plywood, ripping simply means means cutting across the width of the workpiece.
- Page 26 CHANGING BELT 8. Maintenance This table saw has TEFC motor and sealed lubricated bearings, which requires very little Make sure the power cord is disconnected from maintenance other than minor lubrication and the power source! cleaning. Please do the maintenance as following 1.
- Page 27 9. Trouble Shooting PROBLEM SOLUTION SAW WILL NOT START 1. Saw not plugged in. 1. Plug in saw. 2. Fuse blown or circuit breaker tripped. 2. Replace fuse or reset circuit breaker. 3. Cord damaged. 3. Have cord replaced by a certified electrician. OVERLOAD KICKS OUT FREQUENTLY 1.
- Page 28 10. Exploded View and Parts List Table Saw Body Exploded View...
- Page 29 Body Assembly Parts List REF# DESCRIPTION REF# DESCRIPTION Left extension table Lock washer 5 Cap screw M8-1.25 x 35 Button HD screw M5-.8 x 12 Lock washer 8 Lead screw bracket Flat washer 8 Button HD screw M5-.8 x 16 Table insert (standard) Lock nut M8-1.25 Set screw...
- Page 30 Trunnion Assembly Exploded View...
- Page 31 Trunnion Assembly Parts List REF# DESCRIPTION REF# DESCRIPTION REF# DESCRIPTION Lock nut M16-2 Spacer (Nylon) Int retaining ring 24 Flat washer 16 Cap screw M6-1 x 35 Tilt leadscrew nut Cap screw M8-1.25 x 20 Shaft bracket Tilt leadscrew base Lock washer 8 Main trunnion Roll pin 4 x 16...
- Page 32 Blade Guard Exploded View GLIDER Saw Blade Guard (UL62841) DESCRIPTION DESCRIPTION Pan HD screw M4-0.7x12 Nickel Pan HD screw M4-0.7x28 Nickel Plastic spacer Spreader Left guard Right guide block Guard support Left guide block Left cover Roller Plastic liner Bearing 689ZZ Front guard Right cover Cap screw M3-0.5x8 Nickel...
- Page 33 36″Extension Table Exploded View DESCRIPTION DESCRIPTION Cap screw M8-1.25 x 35 Lock washer 8 Flat washer 8 Extension Table (width 365mm)
- Page 34 Switch Exploded View Switch (UL62841): DESCRIPTION DESCRIPTION Safety pin O type terminal Chain Switch bracket Tapping screw M3.5x19 Tapping screw M3.5x10 Switch Spring terminal Switch box Overload protection switch Pan HD screw M4-0.7x8 Strain relif PG13.5 Lock washer 4 Cable for power supply Flat washer 4 Cable for motor Note: The Power switch and circuit breaker used for voltage conversion (115V/230V) are provided with the...
- Page 35 Switch ( CE): DESCRIPTION DESCRIPTION Plastic panel Switch bracket Switch panel Flat washer 6 Electromagnetic switch Spring washer 6 Switch box Button HD screw M6X16 Power line Knurling pin 716 Single core wire Overload protection switch 717 ...
- Page 36 Over Arm Exploded View DESCRIPTION DESCRIPTION Flexible hose (1-1/2” 0.8m) Lock washer 6 Hose Connector 1-1/2" Bracket Over arm Flexible hose (1-1/2” 1m) Cap screw M6-1x16 Clamp Flat washer 6 Cap screw M6-1x12...
Need help?
Do you have a question about the ALPHA HW110LC-36Pro and is the answer not in the manual?
Questions and answers
I have a master fence on a ALPHA HW110LC-36P saw which the fence is not moving smoothly