BlueAnt Pump Air Lite 2 Manual

Inside the box

Get to know your Pump Air Lite 2

1. Charging Case LED Light
2. Charging Port
3. Multifunctional (MFB)/Command Button
4. Earphone LED
5. Magnetic Charging Pin
6. Earphone Mic

Charging your Pump Air Lite 2

1. Open the charging case
   
2. Place earbuds in case
   
3. Close the lid
   

Use the supplied charging cable. Please use only 5V/1A chargers.

The Pump Air Lite 2 takes 2 hrs for a full charge.

The Pump Air Lite 2 charging case takes 2.5 hrs for a full charge. The charging case should charge the earbuds 4 times.

Charging the case

The charging case features a dual-color LED that indicates the charging status and battery level.

While charging, the LED will turn solid white and periodically flash red to indicate the charging progress:

• 1 flash: 25% charged
• 2 flashes: 50% charged
• 3 flashes: 75% charged
• 4 flashes: 76-100% charged

Once the LED turns solid red, the case is fully charged and can be unplugged.

Checking Case Battery Level When Not Charging
To check the battery level when the case is not charging, remove both earbuds and place them back into the case. The LED will periodically flash red to indicate the current charge level, with the number of flashes as described above.

Charging the Earbuds
Each earbud has an LED that will light up solid white during charging. The LED will turn off once the earbuds are fully charged. Please note that the left and right earbuds may charge at different rates.

Let's Get Started

Pairing to your phone

1. Remove both earbuds from the charging case and place them in your ears.
2. When the earbuds are turned on for the first time, they will automatically enter Bluetooth pairing mode.
3. After a few seconds, you will hear the words "Bluetooth pairing."
4. On your phone, search for the Bluetooth device named 'BlueAnt Pump Air Lite2' and select it to pair. You should hear, "Connected."
5. The earbuds will automatically reconnect to your phone whenever you remove them from the charging case. They will disconnect and power off when placed back in the case.

Pairing with a New Device

• If you need to pair the earbuds with another phone, first turn off Bluetooth on the currently connected phone.
• The earbuds will announce, "Disconnected," followed shortly after by "Bluetooth pairing."
• On the new phone, select 'BlueAnt Pump Air Lite2' to complete the pairing.

N.B. If your earbuds are showing up as two separate devices, it means they have become disconnected from each other.

Fit

To ensure the best sound, you need the best fit. Having the best fit creates a seal and enhances the bass performance.

The diagram below, is how the earbuds should sit in your ear. There are 3 sizes of ComfortSeal Tips - Small, Medium and Large.

To get the most out of the earbuds, it's best to try out each of the sizes to get the best fit.

Button Functions

Listen

	Tap once to Play/Pause
	Double tap the Right earbud to Skip Forward
	Double tap Left earbud to Skip Back

Talk

	Tap once to Answer Call
	Tap once to End Call
	Press and hold to Reject Call

Siri/Google

Tap MFB three times to Activate/Cancel Siri/Google

Volume
When music is playing or on a call

	Press and hold the MFB on the Right earbud to increase volume
	Press and hold the MFB on the Left earbud to decrease volume

Power

1. When you remove the earbuds from the charging case, they will automatically power on and try to reconnect to the last phone they were connected to.
   
2. When you place the earbuds into the charging case, they will automatically power off.
   
3. To power on without the charging case, press and hold the MFB for 2s.
   To power off without the charging case, press and hold the MFB on either earbud for 6s.
   
4. To pair without the charging case from off, press and hold the MFB on one earbud for 5s, and then pair with your phone. Then press and hold MFB on the other earbud for 2s to power it on.
   • The earbuds announces when the battery is low, when there is about 30 mins of play time left.
   • The earbuds features an iPhone battery meter.
   • Mono Operation: It is possible to use the earbuds as a mono headset. Simply remove one of the earbuds from the charging case.

How to Re-Sync Your Pump Air Lite 2 Earbuds

If your earbuds become disconnected from each other and show up as two separate devices on your phone, or if you are replacing a lost earbud, follow these steps to re-sync them:

1. Remove any existing pairing of the earbuds from your phone.
   • You should not have any 'BlueAnt Pump Air Lite2' showing up under paired devices on your phone.
   • Ignore anything showing up as an available device at this point.
2. 
   Ensure your charging case is fully charged (the battery indicator LED is periodically flashing red 4 times).
3. Place both earbuds back into the charging case.
   • The LED on the earbuds should turn solid white, indicating that they are charging.
   • If the LED is flashing, adjust the earbud to ensure proper contact until the LED is solid.
4. Within the first few seconds of putting them in the case (with a solid white LED), press and hold the MFB on both earbuds for 10s until you see both LEDs flash quickly twice.
   • The LED may turn off during the 10s if the battery was already fully charged.
   • If you are having trouble achieving the 2 fast flashes, make sure you are starting with a solid white LED. Sometimes, it may require leaving the earbuds out of the case for 10 minutes to deplete the battery a little so they don't switch off quickly after being inserted back into the case.
   • If only one bud flashes 2 times, remove and re-insert both buds, then restart the process.
5. Once both earbuds flash 2 times, remove them from the case, wait 5s for re-syncing to occur, and then scan for BT devices on your phone. You should now see a single 'BlueAnt Pump Air Lite2' which you can connect to.

Sweatproof

The Pump Air Lite 2 earbuds are sweatproof, while the charging case is not. Please take care to avoid moisture and liquids, entering the charging case.

Important Safety Information

PLEASE READ THIS ENTIRE DOCUMENT CAREFULLY, BECAUSE IT CONTAINS IMPORTANT INFORMATION ABOUT THE SAFE USE OF BLUEANT DEVICES
ONLY CHARGE WHEN DEVICE IS CLEAN AND DRY

PROTECT YOUR HEARING
BLUEANT DEVICES CAN REACH VOLUMES ABOVE 100 DECIBELS.
PROLONGED USE AT HIGH VOLUMES MAY AFFECT YOUR HEARING CAPACITY AND MAY RESULT IN NOISE INDUCED HEARING LOSS (NIHL).
TURN OFF THE POWER TO YOUR DEVICE WHEN NOT IN USE.
Please ensure that the device and any associated components such as ear gels or chargers, are stored safely and that any packaging or unwanted contents are disposed of thoughtfully. Do not place the product on the floor or leave it in a place, where young children could access it, or someone could trip over it

Using Ear Gels

Your BlueAnt earbuds will come with ear gels or foam tips that are designed to provide a secure fit in your ear, while providing high quality audio

• Ear gels and tips are designed to sit comfortably in your ear and should not be forced into your ear at any time. If you have trouble fitting the ear gel or foam, please refer to the owner's manual for correct insertion and usage information.

Always make sure that the ear gel or foam is fitted securely to your device, before placing it in your ear.

NOTE THAT NON COMPLIANCE, MISUSE OR FORCING THE EAR GEL OR FOAM MAY CAUSE DAMAGE TO YOUR EAR CANAL EARDRUM, OR MAY OTHERWISE CAUSE BODILY HARM

Care and Handling

Your BlueAnt Bluetooth device is a precision engineered instrument. To ensure its ongoing performance, you should look after it as you would any quality consumer electronic product, and use it in accordance with the instructions.
BlueAnt recommends that you take the following precautions.

• Avoid leaving your device in direct sunlight, such as on the dashboard or console of a car or truck. Do not leave your device unattended in your vehicle.
• Do not leave your device, or use your device, in any area where the temperature may exceed 60 degrees Centigrade (140 degrees Fahrenheit), such as inside a closed car on a hot day. Remember that on a hot day, the temperature inside a closed car may be significantly higher than the outside air temperature.
• Do not leave your device, or use your device, in any area exposed to humidity, dust, soot, other foreign objects, smoke, or steam as this may cause your device to malfunction.
• Do not use any household or industrial grade detergents or cleaners to clean your device. If your device becomes dirty or smeared, in most instances, a wipe with a dry or slightly damp cloth should be sufficient to clean it.
• Do not leave your Bluetooth device, plugged into a wall or car charger for long periods after it is fully charged. BlueAnt does not recommend long periods of continued charging.
• Before charging your BlueAnt device, make sure that the AC outlet, adaptor and cable are not damaged. If you notice any abnormalities, seek advice from a qualified professional.
• If travelling internationally, ensure that your BlueAnt wall or car power adapter is approved for use in the country where you plan to use it and that the adapter voltage is suited to the local power supply.
• Should a fault develop with your BlueAnt product, contact BlueAnt for advice on how to proceed. Do not attempt to repair or alter any BlueAnt product yourself.

Approved Accessories

The use of accessories not approved by BlueAnt, including but not limited to batteries, antennas, wall adapters, car chargers, ear gels, foam tips and convertible covers, may cause your BlueAnt device to malfunction, or in the case of nonapproved electrical accessories, may cause the device to exceed RF energy exposure guidelines. Use only 5V/1A chargers.
Use of non approved accessories will void your device's warranty. For a list of approved BlueAnt accessories, visit our website www.blueantwireless.com

REGISTER & SCAN TO EXTEND YOUR WARRANTY
Register your BlueAnt product for warranty and new product updates by scanning the QR Code.
register.blueantwireless.com

HELP & SUPPORT
Visit support.blueantwireless.com or email: care@blueantwireless.com
blueantwireless.com