Advertisement

BlueAnt Pump Air ANC2 Manual

Inside the box

Get to know your Pump Air ANC 2

Overview

  1. Charging Case LED Lights
  2. Charging Port
  3. Multifunctional (MFB)/Command Button
  4. Earbud LED
  5. Magnetic Charging Pin
  6. Microphones

Charging your Pump Air ANC 2

  1. Open the charging case
  2. Place earbuds in case
  3. Close the lid

Use the supplied charging cable. Please use only 5V/1A chargers.

The Pump Air ANC 2 takes 2 hours for a full charge.

The Pump Air ANC 2 charging case, takes 2 hours for a full charge. The charging case should charge the earbuds 4 times.

  • The charging case has an LED bar on each side. When the charging case is being charged these LED bars will charge from the sides towards the middle. The length of the LED bars signifies the charge level of the charging case.
    Lights 25% on each side
    Lights 50% on each side
    Lights 75% on each side
    Lights 100% on each side

    The LED lights on both sides of the charging case will turn off when fully charged. Please unplug the charging case.

  • The charging case battery level indicator lights turn on when you remove or replace the earbuds in the charging case. This is to let you know the charge level of the charging case.
  • The earbuds have a light that lights up when it's charging. The earbuds turn off when fully charged. The earbuds may charge at different rates for left and right sides.

Let's Get Started

Pairing

In order to get started using the Pump Air ANC 2, we need to pair it to your phone.

  1. Remove both earbuds from the charging case, and put them in your ears.
  2. After a few seconds, they will play a sound in each ear, to let you know that both are connected.
  3. When the earbuds turn on for the first time, it will go into pairing mode.
  4. Now search your phone for 'BlueAnt Pump Air ANC 2' and pair.
  5. The earbuds will auto-reconnect to your phone whenever you take them out of the charging case, and power off when you put them back in.

If you need to pair with another phone, please turn off Bluetooth on the connected phone.
The earbuds will say, 'Disconnected' followed by 'Pair Me'.
Now select the 'BlueAnt Pump Air ANC 2' on the new phone to connect.

Fit

To ensure the best sound, you need the best fit. Having the best fit creates a seal and enhances the bass performance.

The diagram below, is how the earbuds should sit in your ear. There are 3 sizes of ComfortSeal Tips - Small, Medium and Large.

To get the most out of the earbuds, it's best to try out each of the sizes to get the best fit.

Button Functions

Active Noise Cancellation (ANC)

ANC - Single tap on Left earbud (default)
Transparency - Single tap on Left earbud

Music

Tap Right earbud once to Play/Pause
Double tap the Right earbud to Skip Forward
Double tap Left earbud to Skip Back

Call Control

Tap MFB once on either earbud to Answer/End Call
Double tap on MFB on either earbud to end a call
Press and hold MFB on either earbud to Reject Call

Siri/Google

Click MFB 3 times on earbuds to Activate/Cancel Siri/Google

Volume
When music is playing or on a call

Press and hold the MFB on the Right earbud to increase volume
Press and hold the MFB on the Left earbud to decrease volume

Power

  1. When you remove the earbuds from the charging case, they will automatically power on, and try to reconnect to the last phone they were connected to.
  2. When you replace the earbuds in the charging case, they will automatically power off and disconnect from the connected phone.
  3. To power on without the charging case, press and hold the MFB for 2s.
    To power off without the charging case, press and hold the right earbud MFB for 6s.
  4. To pair without the charging case from off, press and hold the right earbud MFB for 5s, and then pair with your phone. Then press and hold the MFB on the other earbud for 2s to power it on.
    • The earbuds announces when the battery is low, when there is about 30 mins of play time left.
    • The earbuds features an iPhone battery meter.
    • Mono Operation: It is possible to use the earbuds as a mono headset. Simply remove one of the earbuds from the charging case.

Buds Lost Connection

  1. Place earbuds in the case. Press & hold the MFB button on both earbuds for 10s
  2. Earbuds will flash white, 4 times
  3. Remove both earbuds from case
  4. Place earbuds within 10cm from each other
  5. Wait 10s until one bud flashes blue/white. Then pair to phone

Sweatproof

The Pump Air ANC 2 earbuds are IP54 sweatproof, while the charging case is not. Please take care to avoid moisture and liquids, entering the charging case.

Important Safety Information

PLEASE READ THIS ENTIRE DOCUMENT CAREFULLY, BECAUSE IT CONTAINS IMPORTANT INFORMATION ABOUT THE SAFE USE OF BLUEANT DEVICES
ONLY CHARGE WHEN DEVICE IS CLEAN AND DRY


PROTECT YOUR HEARING
BLUEANT DEVICES CAN REACH VOLUMES ABOVE 100 DECIBELS.
PROLONGED USE AT HIGH VOLUMES MAY AFFECT YOUR HEARING CAPACITY AND MAY RESULT IN NOISE INDUCED HEARING LOSS (NIHL).
TURN OFF THE POWER TO YOUR DEVICE WHEN NOT IN USE.
Please ensure that the device and any associated components such as ear gels or chargers, are stored safely and that any packaging or unwanted contents are disposed of thoughtfully. Do not place the product on the floor or leave it in a place, where young children could access it, or someone could trip over it

Using Ear Gels

Your BlueAnt earbuds will come with ear gels or foam tips that are designed to provide a secure fit in your ear, while providing high quality audio

  • Ear gels and tips are designed to sit comfortably in your ear and should not be forced into your ear at any time. If you have trouble fitting the ear gel or foam, please refer to the owner's manual for correct insertion and usage information.

Always make sure that the ear gel or foam is fitted securely to your device, before placing it in your ear.

NOTE THAT NON COMPLIANCE, MISUSE OR FORCING THE EAR GEL OR FOAM MAY CAUSE DAMAGE TO YOUR EAR CANAL EARDRUM, OR MAY OTHERWISE CAUSE BODILY HARM

Care and Handling

Your BlueAnt Bluetooth device is a precision engineered instrument. To ensure its ongoing performance, you should look after it as you would any quality consumer electronic product, and use it in accordance with the instructions.
BlueAnt recommends that you take the following precautions.

  • Avoid leaving your device in direct sunlight, such as on the dashboard or console of a car or truck. Do not leave your device unattended in your vehicle.
  • Do not leave your device, or use your device, in any area where the temperature may exceed 60 degrees Centigrade (140 degrees Fahrenheit), such as inside a closed car on a hot day. Remember that on a hot day, the temperature inside a closed car may be significantly higher than the outside air temperature.
  • Do not leave your device, or use your device, in any area exposed to humidity, dust, soot, other foreign objects, smoke, or steam as this may cause your device to malfunction.
  • Do not use any household or industrial grade detergents or cleaners to clean your device. If your device becomes dirty or smeared, in most instances, a wipe with a dry or slightly damp cloth should be sufficient to clean it.
  • Do not leave your Bluetooth device, plugged into a wall or car charger for long periods after it is fully charged. BlueAnt does not recommend long periods of continued charging.
  • Before charging your BlueAnt device, make sure that the AC outlet, adaptor and cable are not damaged. If you notice any abnormalities, seek advice from a qualified professional.
  • If travelling internationally, ensure that your BlueAnt wall or car power adapter is approved for use in the country where you plan to use it and that the adapter voltage is suited to the local power supply.
  • Should a fault develop with your BlueAnt product, contact BlueAnt for advice on how to proceed. Do not attempt to repair or alter any BlueAnt product yourself.

Approved Accessories

The use of accessories not approved by BlueAnt, including but not limited to batteries, antennas, wall adapters, car chargers, ear gels, foam tips and convertible covers, may cause your BlueAnt device to malfunction, or in the case of nonapproved electrical accessories, may cause the device to exceed RF energy exposure guidelines. Use only 5V/1A chargers.
Use of non approved accessories will void your device's warranty. For a list of approved BlueAnt accessories, visit our website www.blueantwireless.com

HELP & SUPPORT

Register your BlueAnt product for warranty and new product updates at:
register.blueantwireless.com or scan the QR code below

Visit support.blueantwireless.com
Email: care@blueantwireless.com
www.blueantwireless.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download BlueAnt Pump Air ANC2 Manual

Advertisement

Need help?

Need help?

Do you have a question about the Pump Air ANC2 and is the answer not in the manual?

Questions and answers

Table of Contents