BlueAnt Pump Air Epic Manual

Also See for Pump Air Epic:

User manual (20 pages)

Table of Contents

Contents

1 Inside the box
2 Get to know your Pump Air Epic
3 Charging your Pump Air Epic
4 Let's Get Started
- 4.1 Pairing
- 4.2 Fit
5 Button Functions
6 Power
7 Support
8 Sweatproof
9 Important Safety Information
10 Support
11 Documents / Resources
- 11.1 References
- 11.2 Download manual

BlueAnt Pump Air Epic Manual

Inside the box

Get to know your Pump Air Epic

Item	Function
1	Charging Case LED Lights
2	Charging Port
3	Multifunctional (MFB)/Command Button
4	Earbud LED
5	Earphone Microphones
6	Case Battery Level button

Charging your Pump Air Epic

Open the charging case
Place earbuds in case
Close the lid

Use the supplied charging cable. Please only use 5V/1A wired chargers or 5V/2A wireless chargers.

The Pump Air Epic takes 2 hours for a full charge.

The Pump Air Epic charging case, takes 2 hours for a full charge. The charging case should charge the earbuds 3 times.

The charging case has 3 lights. These signify the charge level of the charging case.
One (1) light per 33% charge level

1 light 33%, 2 lights 66%, 3 lights 100%
Once fully charged, all 3 lights will remain lit. Unplug the charging case.
When the earbuds power on, they will announce High, Medium or Low battery level. When low, recharge the earbuds by placing them in the case.
When charging the earbuds, the left and right charging case lights will turn red, and glow to show that the earbuds are charging. When fully charged the lights will turn off. The earbuds may charge at different rates for left and right sides.
To check the charge level of the case, press the button on the back of charging case.

Let's Get Started

Pairing

In order to get started using the Pump Air Epic, we need to pair it to your phone.

Please remove both earbuds from the charging case, and put them in your ears.
After a few seconds, they will play a sound in each ear, to let you know that both are connected.
When the earbuds turn on for the first time, it will go into pairing mode.
Now search your phone for 'BlueAnt Pump Air Epic' and pair.
The earbuds will auto-reconnect to your phone whenever you take it out of the charging case, and power off when you put it back in.

If you need to pair with another phone, press and hold the right hand side command button, to power off the earbuds. Then let go of the button, then press and hold the button for 5 seconds until you hear the earbud saying, 'Bluetooth pairing'. Repeat the pairing process on the new phone.

Fit

To ensure the best sound, you need the best fit. Having the best fit creates a seal and enhances the bass performance.

This diagram shows how the earbuds should sit in your ear:

There are 3 sizes of ComfortSealTips - Small, Medium and Large.

To get the most out of the earbuds, it's best to try out each of the sizes to get the best fit.

Button Functions

Active Noise Cancellation (ANC)

ANC - Single tap on Left earbud (default)

Transparency - Single tap on Left earbud (default)

Music

Tap Right earbud once to Play/Pause

Double tap the Right earbud to Skip Forward

Double tap Left earbud to Skip Back

Call Control

Press & hold either earbud to reject a call

Tap MFB once on either earbud to answer a call

Double tap MFB on either earbud to end a call

Siri/Google

Tap MFB on Right earbud three times to Activate/Cancel Siri/Google

Volume

When music is playing or on a call

Press and hold the MFB on the Right earbud to increase volume

Press and hold the MFB on the Left earbud to decrease volume

Power

When you remove the earbuds from the charging case, it will automatically power on, and try to reconnect to the last phone it was connected to.
When you replace the earbuds in the charging case, they will automatically power off and disconnect from the connected phone.
To power on without the charging case, press and hold the MFB for 2 seconds. To power off without the charging case, press and hold the right earbud MFB for 6 seconds.
To pair without the charging case from off, press and hold the right earbud MFB for 5 seconds, and then pair with your phone. Then press and hold the left earbud MFB for 2 seconds to power it on.

The earbuds announces when the battery is low, when there is about 30 mins of play time left.
The earbuds features an iPhone battery meter.
Mono Operation: It is possible to use the earbuds as a mono headset. Simply remove one of the earbuds from the charging case.

Support

For help and support, visit: support.blueantwireless.com

By using this product, you agree to the terms and conditions listed on the BlueAnt website: www.blueantwireless.com

Sweatproof

The Pump Air Epic earbuds are sweatproof, while the charging case is not. Please take care to avoid moisture and liquids, entering the charging case.

Important Safety Information

PROTECT YOUR HEARING BLUEANT DEVICES CAN REACH VOLUMES ABOVE 100 DECIBELS.

PLEASE READ THIS ENTIRE DOCUMENT CAREFULLY, BECAUSE IT CONTAINS IMPORTANT INFORMATION ABOUT THE SAFE USE OF BLUEANT DEVICES

ONLY CHARGE WHEN DEVICE IS CLEAN AND DRY

PROLONGED USE AT HIGH VOLUMES MAY AFFECT YOUR HEARING CAPACITY AND MAY RESULT IN NOISE INDUCED HEARING LOSS (NIHL). TURN OFF THE POWER TO YOUR DEVICE WHEN NOT IN USE.

Please ensure that the device and any associated components such as ear gels or chargers, are stored safely and that any packaging or unwanted contents are disposed of thoughtfully. Do not place the product on the floor or leave it in a place, where young children could access it, or someone could trip over it.

Using Ear Gels

Your BlueAnt earbuds will come with eargels or foam tips that are designed to provide a secure fit in your ear, while providing high quality audio

Ear gels and tips are designed to sit comfortably in your ear and should not be forced into your ear at any time. If you have trouble fitting the ear gel or foam, please refer to the owner's manual for correct insertion and usage information.

Always make sure that the ear gel or foam is fitted securely to your device, before placing it in your ear.

NOTE THAT NON COMPLIANCE, MISUSE OR FORCING THE EAR GEL OR FOAM MAY CAUSE DAMAGE TO YOUR EAR CANAL EARDRUM, OR MAY OTHERWISE CAUSE BODILY HARM

Care and Handling

Your BlueAnt Bluetooth device is a precision engineered instrument. To ensure its ongoing performance, you should look after it as you would any quality consumer electronic product, and use it in accordance with the instructions.

BlueAnt recommends that you take the following precautions.

Avoid leaving your device in direct sunlight, such as on the dashboard or console of a car or truck. Do not leave your device unattended in your vehicle.
Do not leave your device, or use your device, in any area where the temperature may exceed 45 degrees Centigrade (113 Degrees Fahrenheit), such as inside a closed car on a hot day. Remember that on a hot day, the temperature inside a closed car may be significantly higher than the outside air temperature.
Do not leave your device, or use your device, in any area exposed to humidity, dust, soot, other foreign objects, smoke, or steam as this may cause your device to malfunction.
Do not use any household or industrial grade detergents or cleaners to clean your device. If your device becomes dirty or smeared, in most instances, a wipe with a dry or slightly damp cloth should be sufficient to clean it.
Do not leave your Bluetooth device, plugged into a wall or car charger for long periods after it is fully charged. BlueAnt does not recommend long periods of continued charging.
Before charging your BlueAnt device, make sure that the AC outlet, adaptor and cable are not damaged. If you notice any abnormalities, seek advice from a qualified professional.
If traveling internationally, ensure that your BlueAnt wall or car power adapter is approved for use in the country where you plan to use it and that the adapter voltage is suited to the local power supply.
Should a fault develop with your BlueAnt product, contact BlueAnt for advice on how to proceed. Do not attempt to repair or alter any BlueAnt product yourself.

Approved Accessories

The use of accessories not approved by BlueAnt, including but not limited to batteries, antennas, wall adapters, car chargers, ear gels, foam tips and convertible covers, may cause your BlueAnt device to malfunction, or in the case of no-napproved electrical accessories, may cause the device to exceed RF energy exposure guidelines.
Use only 5V/1A chargers.
Use of non approved accessories will void your device's warranty. For a list of approved BlueAnt accessories, visit our website www.blueantwireless.com