REALTRUCK VoltStep 20410125T Installation Instructions Manual

Mercedes benz sprinter electric running board

Advertisement

INSTALLATION INSTRUCTIONS
PRODUCT SAFETY & LEGAL DISCLAIMER
IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO
MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY.
Review the product package and contents prior to beginning the installation. Take care when
opening the packaging and removing items. If a return is needed you will want to return the product in
its original packaging if possible.
This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally
and may require additional steps.
Test fit the product on the vehicle prior to any third party modifications and or finishing. The
manufacturer and/or distributors do not accept responsibility for third party charges, labor and or
third part replacement modifications. Some modifications may void the factory warranty.
Exercise due-diligence when installing this product. The manufacturer and distributors of this product
do not accept any responsibility for vehicle damage or personal injury resulting from the installation of
this product. Careless installation and operation can result in serious injury or equipment damage.
This product is for general off-road use. All liability for installation and use rests with the
owner/operator.
INSTALLER: Once installation is complete, please return this guide along with other documentation
included in this product back to the consumer for future reference. The manufacturer/distributors of
this product do not guarantee this particular version will be available at a later date.
REV.01
© 2024 RealTruck RealTruck Products. All rights reserved
www.realtruck.com
589 W. Apollo St., Brea, CA 92821
PART NO.
• 20410125T/PC
PRODUCT DESCRIPTION
• VoltStep Electric Running Board
VEHICLE APPLICAION
• Mercedes Benz Sprinter
P: 888 427 4466
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VoltStep 20410125T and is the answer not in the manual?

Questions and answers

Summary of Contents for REALTRUCK VoltStep 20410125T

  • Page 1 The manufacturer/distributors of this product do not guarantee this particular version will be available at a later date. © 2024 RealTruck RealTruck Products. All rights reserved www.realtruck.com 589 W. Apollo St., Brea, CA 92821 P: 888 427 4466 REV.01...
  • Page 2: Maintenance And Care

    Factory sensors may read shackles or hooks protruding from the fairlead and or tow hooks. • • All sensor testing is completed by RealTruck Products and or third party testing labs on modified vehicles. • Sensor sensitivity, factory sensor housing, orientation, and operating conditions are all variables that will influence functionality of the sensors.
  • Page 3 WARNING: Keep a minimum of 10” safe distance while the RealTruck VoltStep is operating to avoid any personal injury or damage to the running boards. RealTruck VoltStep s are not designed to provide vehicle body protection. Components can be damaged by hard impact or contact with foreign objects.
  • Page 4: Tools Needed For Installation

    M6 x 20mm CAP HEAD SCREW 4 PIECE M6 x 25mm CAP HEAD SCREW RealTruck recommends you, the installer, read this installation instruction manual from front to back before installing the product. You may also click here to view an installation video or visit https://realtruck.com/installation-instructions/.
  • Page 5 INSTALLATION INSTRUCTIONS BOARD T-NUT End Cap End Cap (black) (red) © 2024 RealTruck Products. All rights reserved REV.01...
  • Page 6 1. At the rear insert the 3/8” U-bolt as shown in Figure 2. The short side is inserted through one hole and out through the other hole. ILLUSTRATION 1. © 2024 RealTruck Products. All rights reserved REV.01...
  • Page 7: Installation Instructions

    ILLUSTRATION 3. STEP 3: Place the BOARD brackets on the main bracket as shown in illustration 4. Secure with: 2 hex head screws. M8 x 100mm, 2 flat and tab washer. ILLUSTRATION 4. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 8 Right side mounted Step 4: Assemble 2 hex nuts. M16 to the M16 stud, then attach the stud to the screw nut and tighten the M16 nuts as shown in illustration 5. ILLUSTRATION 5. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 9 ILLUSTRATION 6. Step 6: Position the square spacer as shown in Figure 7, and then turn the adjusting nut to press the square spacer against the slot in the chassis.. ILLUSTRATION 7. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 10 Step 8: Separate the T-nuts that are inside the bracket and place the bracket on the brackets as shown in illustration 8. Secure with M6 x 25mm screws, M6 flat washer and pressure washer. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 11 Connect the control cable and assign all cables to the marked positions. Return the fuse and hide all the wires. Step 9: Remove the fuse from the harness and connect the battery cable.. ILLUSTRATION 9. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 12 ILLUSTRATION 10. Motor Output Cable Connect the harness to the bracket motor REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 13 (white color) and run the vehicle door signal from the end of the wire connector to the middle of the wire connector and tighten it. ILLUSTRATION 12. Door Switch Wire Vehicle Door Signal Wire REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 14 Please press the red switch button in case of emergency or product failure to protect the vehicle will not be damaged under these conditions. Both boards will return automatically while the emergency switch button is on REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 15 2.- Press the emergency switch button again, and the emergency switch will turn off, and at the same time, the power board will return to its normal working state. 3.- The original state of the emergency switch is OFF. REV.01 © 2024 RealTruck Products. All rights reserved...
  • Page 16: Limited Warranty

    This warranty covers the cost of the product only and does not include the cost of removal, installation, third party modifications or shipping of the product. In no event shall RealTruck Automotive be liable to buyer or any third party for any damage or harm caused by the product or use thereof, regardless of weather such damages were foreseeable and whether or not RealTruck Automotive has been advised of the possibility of such damages, not withstanding the failure of any agreed or other remedy of its essential purpose.

Table of Contents