Hdmi Setup - Marantz SR5005 User Manual

ENGLISH ENGLISH DEUTSCH DEUTSCH
Setting items
Channel Level Test Tone Start : Output test tone.
Set the volume of the test • FL / C / FR / SR / SBR
tone to be the same when it speaker.
is output from each speaker. z When the "Speaker Config." – "S.Back" setting (vpage 57) is set to
"1sp", "S.Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• When o is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 40.
• When you press
setting item immediately.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 56) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover : Set the crossover frequency.
Crossover Freq.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output 250Hz
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
Crossover Freq. to suit the
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
bass reproduction capability
250Hz : Set the crossover frequency.
of the speaker being used.
• "Crossover Freq." can be set when the "Bass Setting" – "Subwoofer
Mode" (vpage 57) setting is "LFE+Main", or when you have a speaker
that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
depending on the "Subwoofer Mode" setting (vpage 57).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
58
Remote control operation
buttons
FRANÇAIS FRANÇAIS ITALIANO ITALIANO ESPAÑOL ESPAÑOL
Setting details
z / SBL z / SL / FHL / FHR / SW : Select the
TEST TONE
on the remote control, you can enter this
Move the cursor
(Up/Down/Left/Right)
NEDERLANDS NEDERLANDS SVENSKA SVENSKA
Setting items
Front Speaker Setup • A：Front speaker A is used.
Set the front speakers to
• B：Front speaker B is used.
use for every surround
• A+B：Both front speakers A and B are used.
mode.
You can switch speakers by pressing SPKR
A/B on the remote control.

HDMI Setup

Make settings for HDMI video/audio output.
Setting items
Auto Lip Sync ON : Compensated.
Make automatic OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out Amp : Play back through speakers connected to the receiver.
Select HDMI audio output TV : Play back through TV connected to the receiver.
device.
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 39 "HDMI control function").
HDMI Control ON : Use HDMI control function.
You can link operations with OFF : Do not use HDMI control function.
devices connected to HDMI
and compatible with HDMI
• When a device that is not compatible with the HDMI control function is
Control.
connected, set "HDMI Control" to "OFF".
• Please consult the operating instructions for each connected component
to check the settings.
• Refer to "HDMI control function" (vpage 39) for more information about
the HDMI control function.
NOTE
• When "HDMI Control" is set to "ON", it consumes more standby
power. If you are not using this unit for an extended period, it is
recommended that you unplug the power cord from the power outlet.
• "HDMI Control" does not work when the power to the equipment is off.
Either turn power on or set to standby.
• The HDMI control function controls operations of a TV that is compatible
with the HDMI control function. Make sure that the TV and HDMI are
connected when you perform HDMI control.
• If the "HDMI Control" settings have been changed, always reset the
power to connected devices after the change.
Confirm the setting
Manual Setup
Setting details
Default settings are underlined.
Setting details
Return to previous menu