Audyssey Settings - Marantz SR5005 User Manual

Setting items
Height Gain Low : Reduce the front height channel volume.
Control the front height Mid : Front height channel sound is output with standard sound volume.
channel volume. High : Increase the front height channel volume.
NOTE
"Height Gain" is displayed for the following settings.
• When "Amp Assign" (vpage 56) is set to "Normal".
• When the "Speaker Config." – "Front Height" setting (vpage 57) is set
to other than "None".
• When surround mode is "PLgz" or the PLgz decoder is used.
Default Yes : Reset to the defaults.
The "Surround Parameter" No : Do not reset to the defaults.
settings are returned to the
default settings.
Tone
Adjust the tonal quality of the sound.
Setting items
Tone Control ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
"Tone Control" can be set when "Dynamic EQ" (vpage 54) is set to
"OFF".
NOTE
The tone cannot be adjusted in the direct mode.
Bass –6dB – +6dB (0dB)
Adjust low frequency range
"Bass" can be set when "Tone Control" is set to "ON".
(bass).
Treble –6dB – +6dB (0dB)
Adjust high frequency range
"Treble" can be set when "Tone Control" is set to "ON".
(treble).
Remote control operation
buttons
SVENSKA SVENSKA NEDERLANDS NEDERLANDS
Setting details
Default settings are underlined.
Setting details
Move the cursor
(Up/Down/Left/Right)
ESPAÑOL ESPAÑOL ITALIANO ITALIANO

Audyssey Settings

Set MultEQ ® , Dynamic EQ ® and Dynamic Volume ® . These can be selected after Audyssey ® Auto Setup
has been performed. For additional information on Audyssey technology, please see page 78.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 10) to return to
the settings after Audyssey Auto Setup was run.
Setting items
MultEQ Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ front L and R speakers.
corrects both time and Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response response.
problems in the listening Manual : Apply frequency response set with "Manual EQ" (vpage 55).
area based on Audyssey OFF : Turn "MultEQ" equalizer off.
Auto Setup calibration. We
recommend "Audyssey".
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
MultEQ is the prerequisite
selected after Audyssey Auto Setup has been performed. "Audyssey"
function for Dynamic EQ
is automatically selected after performing Audyssey Auto Setup. When
and Dynamic Volume.
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
illuminates.
• After running Audyssey Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Freq. have changed without
increasing the number of speakers measured, only
MULTEQ
• Press
set this setting.
NOTE
• "MultEQ" and "Manual" cannot be selected when "EQ Customize" is
set to "Not Used" (vpage 59).
• When using headphones, "MultEQ" is automatically set to "OFF".
Confirm the setting
FRANÇAIS FRANÇAIS DEUTSCH DEUTSCH
Audio Adjust
Default settings are underlined.
Setting details
illuminates.
on the remote control unit to
Return to previous menu
ENGLISH ENGLISH
53