Precor Resolute RSL 515 Assembly Manual
Strength selectorized line converging shoulder press
Hide thumbs
Also See for Resolute RSL 515:
- Assembly manual (15 pages) ,
- Getting started manual (2 pages)
Related Manuals for Precor Resolute RSL 515
Summary of Contents for Precor Resolute RSL 515
- Page 1 ENGLISH Resolute™ Strength Selectorized Line Converging Shoulder Press RSL 515 Assembly Guide...
-
Page 3: Assembly Requirements
Assembly Requirements CAUTION Installation Requirements Required Tools Box cutter Rubber mallet Trademarks ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... -
Page 4: Parts List
Back pad Weight plates 10 lb (4.5 kg) Seat assembly Weight labels Collars Upper cross brace Bumpers Shaft Roller assembly Gas spring Hole plugs Kick plate Guide rods ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... -
Page 5: Frame Assembly
Have your assistant hold frame parts in place during assembly. Image Hardware Instructions kick plate Align to second hole from right. plate. Hand tighten only. ly in a later step. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... - Page 6 Connect upper cross brace to main frame Do not tighten the M10 screws installed in step 1 at this time. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
-
Page 7: Moving Parts
43 36 frame . Each arm has labels. Match the arm labels placement. tered and secure. mallet if needed. Remove all labels. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... -
Page 8: Seat Assembly
(ensure the position of the roller tool does not change). Remove tool. Attach seat pad to seat assembly ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... -
Page 9: Route The Cable
Fully tighten to 50 ft-lb (67.7 N-m). the cable retainer. Route the cable around the pulley and then replace the cable retainer. Tighten to 50 ft-lb (67 N-m) of torque. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide... - Page 10 Finish the Weight Stack Tower Image Hardware Instructions Remove the guide rod fasteners installed in step 1 of the Frame Assembly. 54 48 top plate assembly user side. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
- Page 11 Tighten M10 screws to 32 ft-lb (43 N-m) of torque. 54 48 M10 nylon lock nut Remove the cap from the guide rod and place the rod into bracket opening se ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
- Page 12 At least six turns of the threads on the cable bolt extend into the 1.61 inch (41mm). should be no more than Tighten the locking bolt against the select stem to 50 ft-lb (81 N-m) of torque. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
- Page 13 Install the upper rear and front shrouds . Ensure to hook them over the buttons and spacers. Recommended bolt torque is 25 ft-lb (34 N-m). Securely snap top tray into place. ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
-
Page 14: Complete The Assembly
Complete the Assembly equipment. IMPORTANT types. Standards can be changed or updated. Precor recommends that you keep apprised of your local industry standards. Precor shall not be liable for fail Final Checklist • • • • • • • ©2019 Precor Inc. | Converging Shoulder Press RSL 515 | Assembly Guide...
Need help?
Do you have a question about the Resolute RSL 515 and is the answer not in the manual?
Questions and answers