Landoll Brillion 3620 Operator's Manual
  1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. Brillion 3620
  6. Operator's manual

Landoll Brillion 3620 Operator's Manual

Pulvi-mulcher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
'
Pulvi-Mulcher
3620 Model
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-821-2408

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Brillion 3620 and is the answer not in the manual?

Questions and answers

Related Manuals for Landoll Brillion 3620

Summary of Contents for Landoll Brillion 3620

  • Page 1 ‘ Pulvi-Mulcher 3620 Model Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-821-2408...
  • Page 2 Manuals for 3620 Pulvi-Mulcher Manual Number Manual Type F-821 Operator’s Manual F-820 Parts Manual...
  • Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
  • Page 5 Table of Contents Safety Introduction ............1-1 Description of Unit .
  • Page 6 TABLE OF CONTENTS Purging the Hydraulic System ........2-22 Purge the Lift Circuit .
  • Page 7 TABLE OF CONTENTS Maintenance General Torque Specifications ........4-1 Hydraulic Fitting Torque Specifications.

  • Page 9: Warranty Registration

    Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll personal injury or death, damage to the Corporation Ag Products on-line registration process.

  • Page 10: Transporting Safety

    TABLE OF CONTENTS SAFETY Safety • When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the NOTE sign from abrasion, damage, or obstruction from Investigation has shown that nearly 1/3 of all farm mud, dirt, oil etc.

  • Page 11: Maintenance Safety

    TABLE OF CONTENTS SAFETY Safety Instructions for Towing Maintenance Safety Vehicles • Block the machine so it will not roll when working on or under it. The maximum travel speed is the lesser of • All Transport Locks must be installed. •...

  • Page 12: High Pressure Fluid Safety

    TABLE OF CONTENTS SAFETY High Pressure Fluid Safety Safety Chain 1. Use a Safety Chain to help control drawn machinery Escaping fluid under pressure can be nearly invisible and should it separate from the tractor drawbar. have enough force to penetrate the skin causing serious injury.
  • Page 13 A S S O C I A T I O N ITEM 6 ITEM 8 - 3J675 2-573-010198 To prevent serious injury or death from pinching: Landoll Company, LLC Marysville, Kansas Keep all persons and objects clear while any part of this machine is in www.landoll.com motion.
  • Page 14 TABLE OF CONTENTS SAFETY Figure 1-4: Center Frame Decal Locations F-821-2408...
  • Page 15 TABLE OF CONTENTS SAFETY 3620 OpDrawbarDecals Figure 1-5: Drawbar Decal Locations F-821-2408...
  • Page 16 TABLE OF CONTENTS SAFETY Figure 1-6: Left Hand Wing Decal Locations F-821-2408...
  • Page 17 TABLE OF CONTENTS SAFETY Figure 1-7: Right Hand Wing Decal Locations F-821-2408...
  • Page 18 TABLE OF CONTENTS SAFETY Table provided for general use. NOTES: 1-10 F-821-2408...

  • Page 19: Frame Assembly

    Chapter 2 TABLE OF CONTENTS Assembly IMPORTANT CAUTION All Harnesses must be firmly attached to machine Do Not work on or under this machine unless frame members or Hydraulic Hoses so they do not securely blocked and supported by a hoist or sag or become torn loose by field debris.
  • Page 20 TABLE OF CONTENTS ASSEMBLY Attaching Rockshafts 3. Attach the 4-1/2 x 20 Hydraulic Cylinders base ends to the Lift Cylinder Lugs located on the inside of the 1. Spread open the four UHMV Bearings and place onto center frame tubes using vendor supplied hardware. the Rockshaft.

  • Page 21: Tire Installation

    TABLE OF CONTENTS ASSEMBLY Tire Installation • The Pulvi-Mulcher uses 12.5 x 15 FI Tires and should be inflated to 90 PSI. • Remove the Wheel Nuts from the Hub. See WARNING Figure 2-3. Install a Tire and Wheel Assembly onto each Transport Axle Hub, with 5/8-18 Wheel Nuts Use a torque wrench to assure proper torque.

  • Page 22: Drawbar Installation

    TABLE OF CONTENTS ASSEMBLY Drawbar Installation 3. Install the Turnbuckle to the Leveler with 1-1/4 x 8-1/4 Pin. Place a 1-1/4 x 1-7/8 x 14ga Washer on each end 1. Mount the Drawbar to the lugs on the front of the of pin and secure with 5/16 x 2 Roll Pins.
  • Page 23 TABLE OF CONTENTS ASSEMBLY Leveling Cylinders NOTE Cylinder Ports should be facing upward. 1. Attach the base end of the 3-1/2 x 16 Hydraulic Cylinder onto the Upper Frame Leveling Cylinder Lug 3. Place the Transport Lock over the 3-1/2 x 16 with vendor supplied hardware.
  • Page 24 TABLE OF CONTENTS ASSEMBLY Manual Storage Canister and Wrench Installation Attach the Manual Holder to the frame using 1/4-20 x 1 Bolts, Flat Washers, and Locknuts. See Figure 2-6. Attach the two Open End/Box End Wrenches to the side of the Center Frame and secure with 1/4 x 1-1/4 Lynch Pin.

  • Page 25: Wing Locks

    TABLE OF CONTENTS ASSEMBLY Wing Locks 3. Attach the base end of the 1-3/4 x 6 Hydraulic Cylinder to the Wing Lock Hook. Align the holes, slide 1. Insert the rounded end of the Wing Lock Hook into the 3/4 x 2-3/4 Clevis Pin through, place a 3/4 Flat frame cross member left slot.
  • Page 26 TABLE OF CONTENTS ASSEMBLY Lift Transport Lock Latches, 2. Place Lever Lock Bracket on top of the rear frame cross member. Insert four 1/2-13 x 7-1/2 Bolts with Bracket, and SMV Washers through the top of bracket. Underneath the cross member position two 2-Hole Plates with bolts 1.
  • Page 27 TABLE OF CONTENTS ASSEMBLY Lift Transport Lock through, then place a 3/4 Flat Washer on each side. Secure with 3/16 x 1-1/2 Roll Pins. Assembly 4. Connect the Transport Lock Link to the front Transport Lock Latch, align the holes. Slide 3/4 x 1.
  • Page 28 TABLE OF CONTENTS ASSEMBLY Fold Cylinders Attach the four 4 x 30 Hydraulic Cylinders to the Center Frame Cylinder Lugs, by removing the Cotter Pins and the Pins from the base end of the cylinders and placing them over the cylinder lugs on the frame. Secure by reinstalling the Pins and Cotter Pins.
  • Page 29 TABLE OF CONTENTS ASSEMBLY Fold Cylinder Stops Install Cylinder Stops by removing Clevis Set Screw from Cylinder Clevis. Remove Cylinder Clevis from cylinder rod and place Cylinder Stop over cylinder rod. Reattach Cylinder Clevis, secure with Clevis Set Screw. See Figure 2-11.

  • Page 30: Hydraulic Installation

    TABLE OF CONTENTS ASSEMBLY Hydraulic Installation 5. Using 2 wrenches to prevent twisting, rotate the swivel nut 2 wrench flats (1/3 turn). 6. For reassembly, follow the same procedure but IMPORTANT tighten only 1 wrench flat (1/6 turn). Unfold and lower the unit to the ground and relieve system pressure before attempting to repair, adjust, Tightening Procedure For Swivel O-Ring or disconnect components.
  • Page 31 TABLE OF CONTENTS ASSEMBLY CAUTION Restrictors are installed in the rod end of wing fold cylinders to prevent uncontrolled dropping of wings. Removal of these restrictors, or improper installation can result in serious damage to the implement. Hose Installation 1. Install the Lift Circuit hoses. See Figures 2-14, 2-15 and 2-16.
  • Page 32 TABLE OF CONTENTS ASSEMBLY Hydraulic Lift Layout and Schematic Figure 2-14: Hydraulic Lift Layout 2-14 F-821-2408...
  • Page 33 TABLE OF CONTENTS ASSEMBLY Figure 2-15: Hydraulic Lift Schematic - Rear F-821-2408 2-15...
  • Page 34 TABLE OF CONTENTS ASSEMBLY Figure 2-16: Hydraulic Lift Schematic - Front 2-16 F-821-2408...
  • Page 35 TABLE OF CONTENTS ASSEMBLY Table provided for general use. NOTES: F-821-2408 2-17...
  • Page 36 TABLE OF CONTENTS ASSEMBLY Hydraulic Fold Layout and Schematic Figure 2-17: Hydraulic Fold Layout 2-18 F-821-2408...
  • Page 37 TABLE OF CONTENTS ASSEMBLY Figure 2-18: Hydraulic Fold Schematic F-821-2408 2-19...
  • Page 38 TABLE OF CONTENTS ASSEMBLY Hydraulic Tooth Control Layout and Schematic Figure 2-19: Hydraulic Tooth Control Layout 2-20 F-821-2408...
  • Page 39 TABLE OF CONTENTS ASSEMBLY Figure 2-20: Hydraulic Tooth Control Schematic F-821-2408 2-21...
  • Page 40 TABLE OF CONTENTS ASSEMBLY Purging the Hydraulic System 4. Purge the Circuits accordingly as stated below. 5. Leave the Wing Fold Cylinders extended for installation. IMPORTANT 6. Do Not loosen any hoses or fittings. Unfold and lower the unit to the ground and relieve 7.
  • Page 41 TABLE OF CONTENTS ASSEMBLY Wing Extensions Attach Wing Extensions to each wing with 3/4-10 x 2-1/2 Bolts and Locknuts. Tighten. See Figure 2-21. Wing Extension Bolt,3/4-10 x 2-1/2 Locknut,3/4-10 Figure 2-21: Wing Extensions F-821-2408 2-23...
  • Page 42 TABLE OF CONTENTS ASSEMBLY Wing to Frame Installation NOTE Attach the Wing Frame to the Center Frame before attaching Wing Frame to the Cylinders. If not already assembled on center frame. Insert one 1/2 x 2-1/4 Groove Pin into one end of each 1-3/4 x 11-3/4 Pins.
  • Page 43 TABLE OF CONTENTS ASSEMBLY Hyd Cyl, 4 x 30 Flat Washer, Slotted Nut, 1-1/2 1-1/2-6 Hinge Pin, 1-3/4 x 11-3/4 Washer,1 x 2 x 11ga Thrust Washer,1-3/4 Cotter Pin, 3/8 x 3 Thrust Washer,1-3/4 Pin,1 x 8-3/4 Roll Pin, Washer,1 x 2 x 11ga 5/16 x 2 Figure 2-23: Wing to Frame Installation F-821-2408...
  • Page 44 TABLE OF CONTENTS ASSEMBLY Table provided for general use. NOTES: 2-26 F-821-2408...
  • Page 45 TABLE OF CONTENTS ASSEMBLY Tooth Tube Installation 1. Verify Tooth Tube Bearings are positioned in the proper hole. Top Hole: 20" Crowfoot or 20" Optimizer. See Figure 2-24. Bottom Hole: 24" Notched Wheel. Tooth Tube Bearing Positions for 24" Notched Wheels. See Figure 2-25.
  • Page 46 TABLE OF CONTENTS ASSEMBLY Shank Mounting Dimensions NOTE Mark the tubes for Shank locations prior to installing the Do Not mount the Shanks to the tubes at this time. tubes. See Figures 2-27 and 2-28. Figure 2-27: LH Wing Shank Mounting Dimensions 2-28 F-821-2408...
  • Page 47 TABLE OF CONTENTS ASSEMBLY Figure 2-28: RH Wing Shank Mounting Dimensions F-821-2408 2-29...
  • Page 48 TABLE OF CONTENTS ASSEMBLY Tooth Control Linkage Installation 1. Thread one 1-3/4-5 Nut onto the Cylinder Anchor Rod and insert into rod lug on frame. Thread the other 1-3/4-5 Nut onto the Cylinder Anchor. Snug the two nuts at this time. Install the 4-1/2 x 8 Hydraulic Cylinder by attaching the base end of the cylinder to the Cylinder Anchor Rod then placing Sleeve 1.03 x 2.0 x 1.563 on each side of the base end.
  • Page 49 TABLE OF CONTENTS ASSEMBLY Left Hand Tooth Control Tooth Control Bracket on Tooth Tube by sliding a Clamp Plate into the Tooth Control Bracket Slot and 1. LH Wing Frame, attach a Tooth Control Bracket on under the Tooth Tube with 5/8-11 x 5 Bolts and the top of the Front Tooth Tube by sliding a Clamp Locknuts.
  • Page 50 TABLE OF CONTENTS ASSEMBLY Right Hand Tooth Control Clamp Plate into the Tooth Control Bracket Slot and under the Tooth Tube with 5/8-11 x 5 Bolts and 1. RH Wing Frame, attach a Tooth Control Clamp Locknuts. w/cutout to the Front Tooth Tube by placing the Tooth 3.
  • Page 51 TABLE OF CONTENTS ASSEMBLY Figure 2-33: LH Tooth Control Linkage F-821-2408 2-33...
  • Page 52 TABLE OF CONTENTS ASSEMBLY Figure 2-34: RH Tooth Control Linkage 2-34 F-821-2408...

  • Page 53: Shank Installation

    TABLE OF CONTENTS ASSEMBLY Shank Installation 1. Install all Transport Locks. 2. Assembly Points to Shanks as shown in See Figure 2-35. NOTE 3. Mount the Shanks to the Tooth Control Tubes using See Figures 2-27 and 2-28 for Wing Shank Mounting two 1/2-13 x 5 Bolts and Locknut.
  • Page 54 TABLE OF CONTENTS ASSEMBLY Table provided for general use. NOTES: 2-36 F-821-2408...
  • Page 55 TABLE OF CONTENTS ASSEMBLY Shank Depth Control Place the Limit Valve with the Slide Pad on top between the two holes on the wing frame weldment. Insert 5/16-18 Installation x 5 Bolts up through the weldment on either side of the Shank Adjustment Tube.

  • Page 56: Roller Installation

    TABLE OF CONTENTS ASSEMBLY Roller Installation Refer to Figure 2-38 for roller placement. Place Shim Washer(s) and Dirt Shield on Roller Stub Shaft. Place the Flange Bearing over the Roller Stub Shaft. Lift and support the Roller Assembly up to the Bearing Figure 2-37: Wheel Rotation Hanger.
  • Page 57 TABLE OF CONTENTS ASSEMBLY 128" Long Roller Assembly 128" Long Roller RH Front Assembly LH Front RH Rear 128" Long Roller LH Rear Assembly 132" Long Roller Assembly Figure 2-39: Roller Assembly - Positions F-821-2408 2-39...
  • Page 58 TABLE OF CONTENTS ASSEMBLY Rear Scraper Installation 2. Attach the Scrapers to the Scraper Tube (spaced approximately 4 inches apart) and secure with 3/8-16 Refer to the Mounting Dimensions, See Figure 2-41. U-Bolt and Flanged Locknut. Attach the Scraper Tube to the Wing Scraper Mount and secure with 3/8-16 1.
  • Page 59 TABLE OF CONTENTS ASSEMBLY Scraper Mount Scraper Wing Extension Mount Frame Scraper Tube 132" Lg RH Rear Scrapers 1/4" 3/4" Wing Extension Scraper Scraper Mount Mount Frame Scraper Tube 136" Lg LH Rear Scrapers 1/4" 3/4" Figure 2-41: Scraper Mounting Dimensions F-821-2408 2-41...

  • Page 60: Coil Tine Harrow Installation

    TABLE OF CONTENTS ASSEMBLY Coil Tine Harrow Installation WARNING Refer to Figure 2-43 for Harrow placement. Do not attempt to lift heavy parts (such as the The Coil Tine Harrow comes factory assembled and just frame, rockshaft, and pull hitch) manually. Use a needs the Harrow Adjustment Tubes installed prior to hoist or a fork lift to move these parts into mounting on the 3620.
  • Page 61 TABLE OF CONTENTS ASSEMBLY 3620 OpCoilDragPosition Figure 2-43: Coil Tine Harrow - Positioning F-821-2408 2-43...
  • Page 62 TABLE OF CONTENTS ASSEMBLY Warning Lamp Installation IMPORTANT All Harnesses must be firmly attached to machine 1. Layout the Lamp Harness, noting that the connectors frame members or Hydraulic Hoses so they do not marked with Green Tape is Right Side and Yellow sag or become torn loose by field debris.
  • Page 63 TABLE OF CONTENTS ASSEMBLY Figure 2-44: Warning Lamp Layout F-821-2408 2-45...
  • Page 64 TABLE OF CONTENTS ASSEMBLY Front Scrapers - Optional 2. Attach the Scrapers to the Scraper Tube (spaced approximately 4 inches apart) and secure with 3/8-16 Refer to the Mounting Dimensions, See Figure 2-46. U-Bolt and Flanged Locknut. Attach the Scraper Tube to the Wing Scraper Mount and secure with 3/8-16 1.
  • Page 65 TABLE OF CONTENTS ASSEMBLY Scraper Mount Scraper Mount Wing Extension Frame Scraper Tube 132" Lg RH Front Scrapers view is from the inside of the machine looking forward 1/4" 3/4" Wing Extension Scraper Scraper Mount Mount Frame Scraper Tube 132" Lg LH Front Scrapers view is from the inside of the machine looking forward 1/4"...
  • Page 66 TABLE OF CONTENTS ASSEMBLY V-Leveler Installation - Optional Refer to Wing Leveler Mount Placement Dimensions, See Figure 2-48. Wing V-Leveler Installation 1. Position the Leveler Mounts under the Wing Frames. Slide the Clamp Plate through the Clamp Plate slot. Secure with 1/2-13 x 7 Bolts and Locknuts. 2.
  • Page 67 TABLE OF CONTENTS ASSEMBLY Figure 2-47: V-Leveler Installation - Optional F-821-2408 2-49...
  • Page 68 TABLE OF CONTENTS ASSEMBLY Hinge 13-1/8" 62-1/2" Ref RH Wing Frame Leveler Mount Leveler Bar Hinge 62-1/2" Ref 15-1/8" LH Wing Frame Leveler Mount Leveler Bar Figure 2-48: V-Leveler Mounting Dimensions - Optional 2-50 F-821-2408...

  • Page 69: Rear Hitch - Optional

    TABLE OF CONTENTS ASSEMBLY Rear Hitch - Optional 2. Insert the Tandem Harness Adapter into the bulkhead plate and secure with 1/4-20 x 1 Bolts and Locknuts. 1. Position the Rear Hitch to the rear frame hitch plates, 3. Hook up Tandem Haul Adapter to tractor side of insert 3/4-10 x 3 Bolts in the middle and bottom holes.
  • Page 70 TABLE OF CONTENTS ASSEMBLY Roller Clamp Spacer 3. If there is a gap between the Axle Clamp and the Wheel Stop, install the appropriate Clamp Spacer Installation - Optional with 3/8-16 x 1-3/4 Bolt and Locknut. See Figure 2-50. The Clamp End Spacers are used to eliminate space See Maintenance Section for a list of other Kits that are between the Axle Clamp and the Wheel Stop.
  • Page 71 Chapter 3 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone a ride on the seeder at any Always lock the tractor drawbar in the center time. Allowing a person to ride on the machine can position when transporting the unit. Failure to do inflict serious personal injury or death to that so can result in serious injury or death and cause person.

  • Page 72: Tractor Preparation

    Make sure the tractor receptacle cover latches over the key way on the 7-Pin Connector to hold The Brillion 3620 Pulvi-Mulcher is designed to be pulled the connector in place. by tractor equipped with a double lip or clevis type hitch.

  • Page 73: Hydraulic Lift System

    TABLE OF CONTENTS OPERATION Hydraulic System • Whenever raising or lowering, find a level area large enough to accommodate the unit when it is fully unfolded. The tractor should be stopped and not IMPORTANT moving with the unit fully raised. Unfold and lower the unit to the ground and relieve •...

  • Page 74: Hydraulic Fold System

    TABLE OF CONTENTS OPERATION Transport Lock Latch Rockshaft Engaged Cylinder Transport Lock with Rockshaft Lug Latch Rockshaft Lug Transport Lock Channel Installed Clevis Pin and Hairpin Clevis Pin and Hairpin Lever Drawbar Leveling Lever Lock Cylinder Bracket Drawbar Stablizing Lever Latch Cylinder Figure 3-3: Transport Locks - Installed Hydraulic Fold System...
  • Page 75 TABLE OF CONTENTS OPERATION Down Pressure RH Wing Frame Valve Slotted Wing Lock Hook Wing Lock Hook Wing Lock Cylinder Figure 3-4: Wing Lock Hooks Wing Fold Cylinder Slotted Wing Slotted Wing Lock Hook Lock Hook RH Wing LH Wing Frame Frame WING LOCK...
  • Page 76 TABLE OF CONTENTS OPERATION Lift Transport Lock Be sure all Transport Locks are either locked or unlocked. Drawbar Leveling Cylinder CAUTION Hairpin Failure to remove both Locks will cause damage Bent Pin to the Rockshaft. Road to Field 1. Raise machine fully. 2.
  • Page 77 TABLE OF CONTENTS OPERATION Rockshaft Cylinder Transport Lock Latch Rockshaft Lug RH Rockshaft Lever Lock Bracket Lever Latch Transport Lock Latch Disengaged from Hairpin Rockshaft Lug Clevis Pin Lever Figure 3-8: Lift Transport Lock Disengaged Transport Lock Rockshaft Transport Lock Latch Latch Cylinder Engaged...
  • Page 78 TABLE OF CONTENTS OPERATION Table provided for general use. NOTES: F-821-2408...

  • Page 79: General Operation

    TABLE OF CONTENTS OPERATION General Operation 5. Allow just enough looseness so each Roller Wheel will turn by itself. If wheels become worn, loosen the 1. The minimum horsepower requirement are 9-10 clamps at the end of each Roller Axle and tighten as horsepower per foot of width.
  • Page 80 TABLE OF CONTENTS OPERATION Coil Tine Harrow 3620 is equipped with a Coil Tine Harrow to remove the ridges caused by the shanks and tire tracks before the rear roller compacts the soil. The double coils are individually mounted for flexibility and backup protection. In general the coil drag should run level from front to rear.
  • Page 81 TABLE OF CONTENTS OPERATION Pin,1 x 7-5/16 RH Coil Tine Hairpin Harrow 1-1/4" Tube Pin,1 x 7-5/16 Hairpin Open End/Box End Wrench 3620 OpCoilDragAdj RH Coil Tine Harrow Harrow Adjustment Pin Holes Set Coil Tine Harrow Pitch Angle Adjustment Tube Gang Bar Plate Figure 3-11: Coil Tine Harrow Adjustment...
  • Page 82 TABLE OF CONTENTS OPERATION Notched Wheel Scraper 1. Unfold and Lower Pulvi-Mulcher on a level surface. 2. Push Notched Wheels against the welded stop. Add Adjustment spacers if needed. See Figures 4-5 and 4-6. 3. Loosen Clamp and position Clamp against the end NOTE wheel and tighten.
  • Page 83 TABLE OF CONTENTS OPERATION Shank Depth Control Shank Depth Control Adjustment Letter Shank Depth 5" 1. A more precise adjustment of the Shanks can be 4-1/2" made using the Shank Depth Control. The “F” setting 3-1/2" refers to the maximum operating depth. See 2-1/2"...
  • Page 84 TABLE OF CONTENTS OPERATION V-Leveler - Optional 1. Adjust the V-Leveler to the highest position that does the required job. A good starting point is 3" to 4" above the soil surface. NOTE 2. Adjust the Wing by removing the 1/2-13 x 3 bolts to The Leveler is set too low if the soil pushes ahead of the raise or lower the Leveler Bar.
  • Page 85 TABLE OF CONTENTS OPERATION Transport 6. Before transporting: • Know the transport height and width of the unit 1. Check and follow all federal, state, and local before transport. Use caution when transporting requirements before transporting the Pulvi-Mulcher. near bridges and power lines. 2.
  • Page 86 TABLE OF CONTENTS OPERATION Table provided for general use. NOTES: 3-16 F-821-2408...

  • Page 87: General Torque Specifications

    Chapter 4 TABLE OF CONTENTS Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.

  • Page 88: Hydraulic Fitting Torque Specifications

    TABLE OF CONTENTS MAINTENANCE Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, & ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.

  • Page 89: Wheel Bearing Maintenance

    TABLE OF CONTENTS MAINTENANCE Fasteners Wheel Bearing Maintenance Before operating your Brillion machine, check all Wheel Bearing maintenance should be performed at the hardware for tightness. Use the Tightening Torque Table beginning of every season of use. Check the wheel as a guide.

  • Page 90: Lubrication Maintenance

    TABLE OF CONTENTS MAINTENANCE Lubrication Maintenance • Grease Turnbuckle every 50 hrs or yearly to prevent seizure. The 3620 Pulvi-Mulcher is equipped with maintenance • Grease Wheels Hubs every 50 hrs. Repack Wheel free bearings in the lifts, leveler, and wing hinges. These Hub bearing annually before each season usage.

  • Page 91: Hydraulic Maintenance

    TABLE OF CONTENTS MAINTENANCE Hydraulic Maintenance Roller Axle Assembly After an initial run of 5-10 hours, check the Roller Axle IMPORTANT Assemblies to insure that the wheels are tight to one Unfold, lower the unit to the ground, and relieve another.
  • Page 92 TABLE OF CONTENTS MAINTENANCE Clamp End Spacers - Kit Part Number 201442 - 3/4" Axle Spacer Kit Part Number 201443 - 1/2" Axle Spacer Optional Installation is the same for either kit. The Clamp End Spacer Kits are used to eliminate space 1.
  • Page 93 TABLE OF CONTENTS MAINTENANCE Kit Part Number 204831 - 1" Axle Spacer 2. Insert two 3/8-16 x 1 Bolts through the Axle Spacers and secure with 3/8-16 Locknuts. Kit Part Number 204832 - 1-1/4" Axle Spacer Refer to the Torque Table for proper bolt torque values. Kit Part Number 204833 - 1-1/2"...

  • Page 94: Warning Lamps

    TABLE OF CONTENTS MAINTENANCE Warning Lamps Storage When connecting in the 7-Pin Warning Lamp Connector: 1. The service life of the Pulvi-Mulcher will be extended by proper off-season storage practices. Prior to 1. Make sure the Tractor has a good clean Receptacle, storing the unit, complete the following procedures: free of dirt and corrosion.

  • Page 95: Maintenance Chart

    TABLE OF CONTENTS MAINTENANCE Maintenance Chart (Subject to change without notice) 100 hours / Initial Run-In 20 Hours 50 Hours Storage Annually Fasteners Grease: Turnbuckle Adjust Scraper if equipped Grease Wheel Hub Repack Wheel Hub Bearings Tighten Roller Axle Wheels and Clamps **Clean Machine Grease After Cleaning...
  • Page 96 TABLE OF CONTENTS MAINTENANCE Table provided for general use. NOTES: 4-10 F-821-2408...
  • Page 97 Chapter 5 TABLE OF CONTENTS Specifications Product Attributes WLB 3620 21 Approximate Weight 21,353 lbs. (9,686 kg) Working Width 21 ft. 0 in. (6.4 m) Transport Width 12 ft. 3 in. (3.7 m) Transport Height 13 ft. 4 in. (4.1 m) Overall Length (Transport) 31 ft.

  • Page 98: Specifications

    TABLE OF CONTENTS SPECIFICATIONS Table provided for general use. NOTES: F-821-2408...
  • Page 99 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 03/20217 Initial Release 02/2018 F-821-0218 Modified Pressure Valve, added Gauge 11/2018 F-821-1118 ECN 44217 - Increased Tube Wall Thickness Updated ISO logos to ISO 9001:2015 (Revised 04/2024) 08/2024 F-821-2408 ECN 50094 - QR Code Decal Updated Template, Drawings, Instruction *Revision Format (Year/Month)
  • Page 100 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001:2015 registration at all Landoll manufacturing facilities. Pulvi-Mulcher 3620 Model Operator’s Manual Re-Order Part Number F-821 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

Table of Contents