Operation - cecotec CONGA 9590 SPIN REVOLUTION ULTRA POWER Instruction Manual

ENGLISH
Installing the mixed tank. Fig. 8
- Open the water-tank silicone lid and carefully fill up the tank while avoiding spillages.
Make sure the lid is properly closed. Never immerse the tank in water or other liquids.
- To install the tank on the robot vacuum cleaner, follow the direction shown in figure 8 and
manually press the tab and push it into the correct position. You will hear a click when it is
properly fixed.
- Install the Spin mops following the direction shown in Figure 8.
Recommendations:
- It is not suggested to use the scrubbing function for first-time use.
- It is recommended to be present when the robot vacuum cleaner is scrubbing.
- In order to achieve perfect scrubbing, it is suggested to moisten the mop before using it.
Wi-Fi connectivity and mobile App
In order to pair your robot vacuum cleaner to your mobile phone, follow the steps below:
- Automatic-scanning mode
Download the Cecotec app from Google Play or App Store or scan the QR code on your
robot vacuum cleaner.
If this is the first time you are using the app you will need to register your account,
otherwise log in.
Once in the app, press on the "+" symbol in the top right corner and the "Add device" option.
On your robot vacuum cleaner, press and hold for a few seconds the Home button until the
robot beeps and the buttons change their flashing frequency.
The device will appear on the display, press on it.
Enter the Wi-Fi password to which the mobile device is connected and select "next".
Wait for the connection to finish.
- Manual-connection mode
Download the Cecotec app from Google Play or App Store or scan the QR code on your
robot vacuum cleaner.
If this is the first time you are using the app you will need to register your account,
otherwise log in.
Once in the app, press on the "+" symbol in the top right corner and the "Add device" option.
On your robot vacuum cleaner, press and hold for a few seconds the Home button until the
robot beeps and the buttons change their flashing frequency.
Press on the robot option you are using.
Enter your home Wi-Fi password.
Follow the steps shown in the app until the linking process is completed.
First use
- Once the robot vacuum cleaner and the charging base are installed, follow these steps
before the first cleaning.
- First of all, fully charge the robot vacuum cleaner. It is suggested to allow the robot to
68
CONGA 9590 SPIN REVOLUTION ULTRA POWER
charge overnight. Once fully charged, it may carry out the first cleaning cycle and save the
first map. To do this, press the Start/Pause button in the app and the robot will map your
house to continue cleaning in the edge and zigzag mode.
- If your house is very large and the robot vacuum cleaner runs out of battery, it will return
to the charging base, save both complete and incomplete maps, and, once charged, it will
resume cleaning where it left off until the entire surface has been mapped. The robot
vacuum cleaner is constantly mapping, so it adapts in an individual and personalised way
to the particularities of each home and constantly improves its map.

3. OPERATION

Robot vacuum cleaner's buttons
Auto Mode
- Press the Start/Pause button on the robot vacuum cleaner or select it in the app to make it
start cleaning automatically in Edge mode and then perform a cleaning cycle in an orderly
zigzag pattern while it also recognises which areas have been cleaned and which have
not. The robot vacuum cleaner will automatically plan the cleaning route during cleaning.
- If you control the robot vacuum cleaner manually during this mode, the robot will
recalculate the route, so it may pass through already cleaned areas. To ensure efficient
cleaning, do not operate the robot vacuum cleaner manually during automatic cleaning.
- Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle,
the robot vacuum cleaner will smartly return to the charging base automatically and once
fully charged, it will resume the cleaning process from the same point.
- During cleaning, the robot vacuum cleaner will stop briefly to evaluate the area and
calculate the cleaning route (this stop will vary depending on the house conditions).
Back Home mode
- Press the Back Home button on the robot vacuum cleaner or from the app to send the robot
vacuum cleaner to the charging base. The robot vacuum cleaner will stop vacuuming until
it reaches the base.
- This mode can be activated during any cleaning cycle.
- The robot vacuum cleaner will take the shortest route back to the charging base thanks to
its map-memorisation feature and the smart back-home function.
- Upon completing a cleaning cycle or when the battery is low, thanks to its TotalSurface
2.0 technology, the robot vacuum cleaner will automatically return to the charging base to
avoid running out of battery. Once the robot has recharged, it will resume cleaning from
the point it has stopped.
ENGLISH
CONGA 9590 SPIN REVOLUTION ULTRA POWER
69