GeKaMac PoWer Plus+ Series Manual Instruction

GeKaMac PoWer Plus+ Series Manual Instruction

Hide thumbs Also See for PoWer Plus+ Series:

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PoWer Plus+ Series and is the answer not in the manual?

Questions and answers

Summary of Contents for GeKaMac PoWer Plus+ Series

  • Page 2 Refer to the nearest GEDIK WELDING authorized service or the service center of GEDIK WELDING when a • problem comes up. ® Thank you for prefering one of GeKaMac products. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 3: Table Of Contents

    10. Welding Operation ..............................10 11. Welding Parameters .............................. 11 12. Machine Maintenance ............................11 13. Troubleshooting ..............................12 14. Warranty Conditions ............................14 15. Warranty Document .............................. 15 ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 4: Safety Rules

    Don’t do welding near hydrolic lines. Always keep a fire extinguisher on hand. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 5: Electricity And Magnetism

    Inlet and outlet cables, telephone cables and control cables that are found in the work area of the • machine. Radio and/or television transmitters and receivers, • ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 6: General Information And Warnings

    Acceptable environmental temperature range during work is between -10 °C and +40 °C. • Acceptable relative humidity rate is 95% at 20 °C. • Manufacturing company reserves the right to change the technical properties without prior notice. • ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 7: Advantages And General Properties Of Power Plus+Tig 200 Dc Pfc

    The front and rear panel are made of engineering plastic, that have features of heat-resistant, corrosion- resistant, to ensure the welder keep normal work even under bad environments. 6. ELECTRICAL PRINCIPLE DRAWING ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 8: Technical Information

    TIG Series should be installed according to picture 1 as below. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 9 ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 10: Layout For Front & Rear Panel

    ) Gas inlet: Gas inlet connection. ( ) (13) Fan: Cooling the machine. (14) Down slope regulation knob: adjust the time of down slope. (15) Current digital display ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 11: Welding Operation

    The operator can choose the manipulation of electrode based on welding joint shape, welding position, electrode spec, welding current and operation skill, etc. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 12: Welding Parameters

    Observe that Whether the current output cable is damaged. If it is damaged, it should be wrapped up, insulated or changed. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 13: Troubleshooting

    • If there is any problem and has no the authorized professional maintenance personal of our company, • please contact local our company agent or the branch company! ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 14 1. If it is because of the potentiometer damage, replace the Input current is unstable or not controlled potentiometer. Or if it caused by the bad connections, by the potentiometer. especially socket connector, need inspection. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 15: Warranty Conditions

    7. Ministry of Science Industry and Technology, The Protection of the Consumer and Competition General Directorate can be refered to whenever a problem concerning the warranty document comes up. 8. Earth clamp and welding kits are not under warranty. ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 16: Warranty Document

    ® GeKaMac Gedik Welding Machines Warranty Document MACHINE INFORMATION ® Brand : GeKaMac Model : …………………………………………………………..........Serial Number : ………………………………………………..........CUSTOMER INFORMATION Company Name : ……………………………………………….......... Authorized Person : …………………………………………….......... Telephone : ……………………………………………………..........Company Address : …………………………………………..........City/Country…………………………..………………………........E-Mail :……………… @………………………..............
  • Page 17 ® GeKaMac Gedik Welding Machines Warranty Document MACHINE INFORMATION ® Brand : GeKaMac Model : …………………………………………………………..........Serial Number : ………………………………………………..........CUSTOMER INFORMATION Company Name : ……………………………………………….......... Authorized Person : …………………………………………….......... Telephone : ……………………………………………………..........Company Address : …………………………………………..........City/Country…………………………..………………………........E-Mail :……………… @………………………..............
  • Page 18 Contact Details: T: +86 21 31295500 | F: +86 21 51919711 Importer: Gedik Kaynak San ve Tic A.Ş Company Adress: Ankara Cad No: 306 Seyhli 34906 Pendik, Istanbul TURKEY Contact Details: +90 216 3785000 ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...
  • Page 19 ® GeKaMac PoWer Plus+TIG 200 DC PFC Welding Machine User’s Guide, 2016...

This manual is also suitable for:

Power plus+ tig 200 dc pfc

Table of Contents