Subscribe to Our Youtube Channel
Related Manuals for Dahua IPC-HFW2439M-AS-LED-B-S2
Summary of Contents for Dahua IPC-HFW2439M-AS-LED-B-S2
- Page 1 Bullet Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.2...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide our official website. The manual is for reference only. Slight differences might be found between the electronic version and the paper version. All the designs and software are subject to change without prior written notice. Product updates might result in some differences appearing between the actual product and the manual.
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2. - Page 5 Quick Start Guide ● We recommend using the device together with lightning arrester to improve lightning protection effect. ● We recommend grounding the device to enhance reliability. ● Do not touch the image sensor (CMOS) directly. Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol.
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Cable ....................................... 1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Changing Device IP Address ..............................6 Logging in to Web Page ................................ -
Page 7: Introduction
Quick Start Guide Introduction Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see FAQ Manual. Figure 1-1 Cables Table 1-1 Cable information Port Port Name Description 1-1 is circular power port, and 1-2 is 2PIM terminal. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Port Port Name Description DC 12V Out Supplies 12 VDC 2W power for external devices. Power port Includes alarm signal input and output ports. See Table Alarm I/O 1-2. RS-485 RS-485 Controls external PTZ and so on. Connects to network with network cable. - Page 9 Quick Start Guide Device collects logic "0" when input signal is grounded. Figure 1-2 Alarm input Step 2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is relay switch output, which can only connect to NO alarm devices. N1 and C1 or N2 and C2 constitute a switch to provide the alarm output, which is shown in Figure 1-3.
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP setting can be finished with the ConfigTool or in web page. For more information, see web operation manual. Device initialization is available on select models, and it is required at first use and after device is ... - Page 11 Quick Start Guide Enter username and password when you want to change IP, configure the system, update the device, restart the device, and more. Step 5 Click OK. Step 6 Select one or several devices in uninitialized status, and then click Initialize. Select the devices to be initialized, and then click Initialize.
-
Page 12: Changing Device Ip Address
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected. Click OK to initialize the device. Step 10 Click the success icon ( ) or the failure icon ( ) for the details. Click Finish. -
Page 13: Logging In To Web Page
Quick Start Guide Figure 2-4 Change IP Address interface Select Static mode and then enter start IP, subnet mask and gateway. Step 3 IP addresses of multiple devices will be set to the same if you select Same IP checkbox. -
Page 14: Installation
Quick Start Guide Installation Packing List The tools required for the installation such as electric drill are not provided in the package. The operation manual and related tools are contained in the disk or the QR code. Dimensions Figure 3-1 Dimensions (mm[inch]) -
Page 15: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation method Figure 3-2 Installation method 3.3.2 Installing SD Card (Optional) Press the reset button for 10 s to reset the device. For devices with motorized vari-focal lens, zoom and focus can be adjusted automatically; for ... - Page 16 Quick Start Guide Figure 3-4 Cable going through the wall...
-
Page 17: Installing Waterproof Connector (Optional)
Quick Start Guide Figure 3-5 Cable going through the cable tray 3.3.4 Installing Waterproof Connector (Optional) This part is only needed when there is waterproof connector in the package and the device is used outdoors. -
Page 18: Adjusting Sunshade Cap
Quick Start Guide Figure 3-6 Install waterproof connector 3.3.5 Adjusting Sunshade Cap Figure 3-7 Adjust sunshade cap... -
Page 19: Adjusting Lens Angle
Quick Start Guide 3.3.6 Adjusting Lens Angle Figure 3-8 Adjust lens angle... - Page 20 Quick Start Guide...
Need help?
Do you have a question about the IPC-HFW2439M-AS-LED-B-S2 and is the answer not in the manual?
Questions and answers