Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fanco Flow DC
Summary of Contents for Fanco Flow DC
- Page 1 Flow Installation Manual Version 1.0...
-
Page 2: Important Safeguards
CEILING FAN INSTRUCTION BOOKLET Thank you for purchasing your Fanco Flow DC Ceiling Fan. Please read all instructions carefully before assembly and use. IMPORTANT SAFEGUARDS: Read all instructions carefully, even if you feel you are quite familiar with this type of appliance. When... -
Page 3: Important Note
21. The LED light panel in the light kit (light models) is user replaceable as it connects with 'Push Plug' wiring. It is user replaceable ONLY with Fanco certified replacement LED panels. Using unauthorised parts may damage the fan, cause undesired results, or be a safety hazard. - Page 4 PREPARATION: 1. Unpack your ceiling fan carefully, then remove all parts and components, and lay on a cloth or soft surface to avoid damage. DO NOT lay the motor housing on its side as the housing may get damaged. 2. Before commencing installation, check that all parts are included. NOTE: You may need to remove all packaging material to ensure there are no missing parts.
-
Page 5: Installation And Assembly
INSTALLATION AND ASSEMBLY: CAUTION! Before installing the fan make sure you have turned OFF the electricity supply. SELECTING A LOCATION: 1. Choose a location for mounting the fan where the blades will have at least 2.1 metres of clearance from the floor. 2. -
Page 8: Installation Steps
INSTALLATION STEPS: IMPORTANT: Ensure the power is OFF when installing this fan. 1. Remove two (2) screws completely, and loosen two (2) screws from the Hanging Plate. 2. Remove the Canopy from the Hanging Plate. Hanging Plate Canopy 3. Fix the Hanging Plate to the Ceiling. IMPORTANT: Ensure Hanging Plate is secure. - Page 9 6. Carefully, turn the motor and blade over. 7. Screw in two (2) screws to the first installed blade. 8. Secure the remaining two (2) blades with screws to the motor. 9. Tighten all six (6) screws. 10. Carefully, turn the motor and blades over. 11.
- Page 10 14. Put the Canopy onto the Motor. 15. Fix into place with three (3) screws that were removed in Step 13. 16. Hang the complete assembly onto the hanging plate using the supplied ‘S’ Hook and connect the cables to the receivers. Once connected, remove the ‘S’ Hook 17.
- Page 11 WITH LIGHT MODELS 1. Hold the Light Kit underneath the fan and connect the Plug Wire of the Fan to the Plug of the Light Kit. 2. Align the Light Kit with the base of the fan. 3. Rotate until firmly in place. IMPORTANT: Take care not to damage the Light Wires.
-
Page 12: Care And Cleaning
5. Align the grooves of the Diffuser with the grooves Light Kit and twist into place. IMPORTANT: Do not overturn. NO LIGHT MODELS 1. Align the No Light Cover with the base of the fan and rotate until firmly in place. IMPORTANT: Do not overturn. - Page 13 PAIRING THE REMOTE: All Flow DC fans are pre-paired and there is no pairing process needed to start the fan. If you want to reset the fan to factory setting. Please follow steps below. 1. Using the wall (isolation) switch, turn the fan power OFF for 10 seconds.
-
Page 14: Functions Of The Remote Control
INSTALLING MULTIPLE FANS: Sometimes you may encounter a remote-control issue when installing multiple fans. For the purposes of this troubleshooting guide: Fan A uses Remote control A and Receiver A, while Fan B uses Remote control B and Receiver B. •... -
Page 15: Troubleshooting
TROUBLESHOOTING: Trouble Possible Cause Suggested Remedy Fans does not start after Remote and receiver are not Re-pair the receiver and remote pairing process. paired successfully Battery flat in remote control Replace the battery in remote control Loose wire connections or Check wire connections and ensure plugs are plugs to fan/receiver positively connected...
Need help?
Do you have a question about the Flow DC and is the answer not in the manual?
Questions and answers