Assa Abloy ACCENTRA YDC201 Installation Instructions

INSTALLATION
INSTRUCTIONS
Option A-
Regular Arm Installation
SPEED ADJUSTING VALVES
DOOR CLOSE �
FOREARM
(Right Hand Door)
� OORCLOSER
�
(Left Hand Door)
-
Option B
Top Jamb Installation
DOOR CLOSER
MAINARM
(Left Hand Door)
80-9316-8007-000 REV-1 (3/17)
�
Option A instructions:
screw hole center locations. Mark four (4) hole locations on door for door closer
and two (2) hole locations on frame for arm shoe.
and frame, drill 7/32"(5.5mm) diameter holes for wood screws or drill and tap
#7(.201" diameter) for 1/4-20 machine screws.
shoe to frame using screws (a) or (b).
(c) or (d).
HINGE SIDE.
Secure tightly with arm screw/washer (e).
perpendicular to frame when assembled to preloaded main arm. Secure forearm
to main arm with screw/washer (f).
FOREARM
reference.
cover with small screw 0).
Option B instructions:
screw hole center locations. Mark four (4) hole locations on door for door closer
and two (2) hole locations on frame for arm shoe.
and frame, drill 7/32"(5.5mm) diameter holes for wood screws or drill and tap
#7(.201" diameter) for 1/4-20 machine screws.
shoe to door using screws (a) or (b). 4. Mount closer on frame using screws
(c) or (d).
HINGE SIDE.
Secure tightly with arm screw/washer (e).
perpendicular to door when assembled to preloaded main arm. Secure forearm
to main arm with screw/washer (f).
reference.
cover with small screw 0).
Approved 2024-05-28
&
Incorrect installation or adjustment
could cause damage or injury.
Read and follow instructions carefully.
Diagram for Option A
6
(152)
m
A
� ----f-- - -
Right hand door shown,
' reverse measurements for
left hand door application.
1
<t_
Hinge or Pivot
1.
Using the measurements from diagram A, mark
SPEED ADJUSTING VALVES MUST BE POSITIONED TOWARD
Install main arm to top pinion shaft, perpendicular to door,
5.
8.
Snap pinion cap over shaft at bottom of closer or install (optional)
Diagram for Option B
� Hinge or Pivot
Left hand door shown,
I
I reverse measurements for
right hand door application.
:
______.,__ _ _ _ _
1 .___
A
1
I
I
I
I
�----.-+OH
(152)
1.
Using the measurements from diagram B, mark
SPEED ADJUSTING VALVES MUST BE POSITIONED TOWARD
Install main arm to bottom pinion shaft, perpendicular to door,
5.
8.
Snap pinion cap over shaft at bottom of closer or install (optional)
YD C2 0 1 AC C C: N T . M
YD C2 0 4 ASSAABIDY
1- 3 /4
9 - / 6
1 1
� ( 2 - 3 � 0 � ) - - ------.i -
Inches (mm)
Door Opening
°
to 100 7
° °
101 to 120 6
° °
121 to 180 3-1/2
2. Drill pilot holes in door
3.
Install adjustable forearm/arm
4.
Mount closer on door using screws
6.
Adjust length of forearm so it is
7.
Adjust closing speed, see page2 for
Inches (mm)
Door Op ening
Dim.A
°
to 00 7 (178)
1
° °
0 to 20
6 (152)
1 1 1
°
121· to 180 3-1/2 (89)
9 _ - �
1 _ _s _ _ _ __
1 1
( 2 30)
6
1- 3 /4
(44.4)
2.
Drill pilot holes in door
3.
Install adjustable forearm/arm
6.
Adjust length of forearm so it is
7.
Adjust closing speed, see page2 for
Dim.A
(178)
(152)
(89)