Download Print this page

Advertisement

Quick Links

CT30, CT30P, CT30QC, CTA30,
CTE30, CTJ30, and CTU30
Cordless Impact Wrench
SAFETY INFORMATION
This manual contains important safety and operating
instructions for Snap-on CT30, CT30P, CT30QC,
CTA30, CTE30, CTJ30 and CTU30 Cordless Impact
Wrenches. Refer to the information in this manual
often for safe operation.
Read All Instructions
Read, understand, and follow all safety messages and
instructions in this manual and on the tool.
General Warnings and
Cautions
Snap-on Tools Company cannot anticipate or provide
safety warnings and cautions to cover every situation
that may be encountered when operating, servicing, or
repairing this tool. It is the responsibility of operators
and servicing technicians to be knowledgeable about
the procedures, tools, and materials used, and to
satisfy themselves that the procedures, tools, and
materials will not comprise their safety.
Do not attempt to operate this tool until you have
thoroughly read and completely understand all
instructions and safety rules contained in this manual.
Failure to comply can result in accidents involving fire,
electric shock, or serious personal injury. Save this
manual and review it frequently for continued safe
operation and to instruct others who may use this tool.
To reduce the risk of fire, electric shock, and personal
injury while using power tools always follow basic
safety precautions, including the safety messages in
this section.
Remember that this tool is always in an operating
mode because it does not have to be plugged into an
electrical outlet.
General Safety Rules—For
All Battery Operated Tools
WARNING
Read and understand all instructions. Failure
to follow all instructions listed below may
result in electric shock, fire, and/or serious
personal injury.
SAVE THESE INSTRUCTIONS
Work Area
WARNING
• Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
• Do not operate in explosive atmospheres, such
as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite
the dust or fumes.
• Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
WARNING
• Do not abuse the cord. Never use the cord to
carry the battery charger. Keep cord away from
heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords
create a fire hazard.
• A battery operated tool with integral batteries or
a separate battery pack must be recharged only
with the specified charger for the battery. A
charger that may be suitable for one type of battery
may create a risk of fire when used with another
battery.
• Use battery operated tool only with specifically
designated battery pack. Use of any other
batteries may create a risk of fire.
Personal Safety
WARNING
• Stay alert, watch what you are doing, and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
• Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing ,and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in
moving parts.
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the CT30 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Snap-On CT30

  • Page 1 SAFETY INFORMATION Work Area This manual contains important safety and operating WARNING instructions for Snap-on CT30, CT30P, CT30QC, CTA30, CTE30, CTJ30 and CTU30 Cordless Impact Wrenches. Refer to the information in this manual often for safe operation. Read All Instructions •...
  • Page 2 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench • Avoid accidental starting. Be sure switch is in Service the locked or off position before inserting battery pack. Carrying tools with your finger on the WARNING switch or inserting the battery pack into a tool with the switch on invites accidents.
  • Page 3 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench • Do not attempt to destroy or disassemble the WARNING battery pack or remove any of its components. • Do not charge using an engine generator or DC •...
  • Page 4 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench • Do not charge battery when temperature is below 32°F (0°C) or above 104°F (40°C). WARNING • Charge battery pack in a well ventilated area. • Do not incinerate the battery, even if severely damaged or completely exhausted.
  • Page 5: Specifications

    CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Authorized Service Center since special tools Applications are required to replace it. — Cord replacement for CTCF318 charger must • CT30 is designed for use with varying applications be done with an identical cord.
  • Page 6 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Using Screwdriver Bit Sockets Two magnetic sockets are available from Snap-on (CTFBS8 and CTFBS9). They permit the use of screwdriver bits with the impact wrench. The magnetic properties of the sockets are not affected by the light impact of cord-free impact tools.
  • Page 7 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Disassembly/Assembly Wiring the Switch Assembly Instructions are explained with the switch button Instructions facing the assembler and the forward/reverse lever positioned above the button. Service 1. With the button of the switch assembly (23) facing the assembler, insert the green wire into the right, top rear slot on the switch assembly.
  • Page 8 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench 7. Slide the washer (14) down the plastic shaft of the gear carrier (12) opposite the hammer (4), spring (7) and eyelet (8). A dab of grease will hold the washer (14) in place.
  • Page 9: Parts Listing

    CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Figure 1: Exploded View – CT30, CT30P, CT30QC, CTA30, CTE30, CTJ30 and CTU30 Parts Listing C6 Retaining ring ........ME7A179 Nose seal (not used on CT30QC) ....ME6A12 C7 Spring Pin ......... ME2A144 Front housing..........
  • Page 10 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench 21 Black wire, motor to switch ......CT30-312 Yellow wire, terminal to switch (not shown) .CT30-315 22 Support terminal assembly ...... CT30-801R 23 Switch assembly.........CT30-153 24 Bottom handle screw (2) ......ME3L26A 25 Rear cover screw (4) ........
  • Page 11 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Notes:...
  • Page 12 CT30, CT30P, CT30QC, CTA30, CTE 30, CTJ30, and CTU30 Cordless Impact Wrench Snap-on® is a registered trademark of Snap-on Incorporated. Loctite® is a registered trademark of Snap-on Incorporated. Torx® is a registered trademark of Snap-on Incorporated. Declaration of Conformity Snap-on Tools Company, 2801 80th Street, Kenosha, WI 53141-1410, U.S.A.

This manual is also suitable for:

Ct30pCt30qcCta30Cte30Ctj30Ctu30