Related Manuals for VWR Basic Vortex Mixer
Summary of Contents for VWR Basic Vortex Mixer
- Page 1 Instruction Manual Basic Vortex Mixer Standard Vortex Mixer Advanced Vortex Mixer Pulsing Vortex Mixer...
-
Page 2: Package Contents
able of ontents Package Contents ....Warranty ....Installation ....Maintenance &... -
Page 3: Installation
Always ensure the power is disconnected from that your equipment is recycled in a manner that protects human health. the unit prior to any cleaning. If the unit ever requires service, contact your VWR’ representative. -
Page 4: Safety Instructions
& r afety nstructions tanDarDs egulations Please read the entire instruction manual before operating the Vortex Mixer. Troemner, LLC hereby declares under it’s sole responsibility that the construction of this product conforms in accordance with the following standards: WARNING! DO NOT use the Vortex Mixer in a hazardous atmosphere or with hazardous materials for which the unit was not designed. -
Page 5: Instructions De Sécurité
nstructions De écurité ormes et églementations Troemner LLC déclare par la présente sous sa seule responsabilité que la fabrication Veuillez lire l’intégralité des instructions avant de faire fonctionner l’agitateur Vortex. de ce produit est conforme aux normes suivantes : AVERTISSEMENT ! N’utilisez PAS l’agitateur Vortex dans une atmosphère dangereuse ou avec des matériaux dangereux pour lesquels l’unité... - Page 6 ixeD PeeD ortexer ixer Pecifications igital ortexer ixer Pecifications Overall dimensions (L x W x H): Overall dimensions (L x W x H): 7 x 4.4 x 5.3” (17.8 x 11.2 x 13.5 cm) 7 x 4.4 x 5.3” (17.8 x 11.2 x 13.5 cm) Electrical (50/60 Hz): 120V: 1.2 amps, 135 watts...
- Page 7 & P igital ulsing ortex ixer ontrol anel The front panel of the Digital/Pulsing Vortex Mixer contains all the switches, controls and displays needed to operate the unit. A. 3-way rocker switch: Auto/standby/on rocker switch starts/stops the vortexing function. B. Time display: Displays accumulated time (continuous mode) or how much time is remaining (timed mode).
- Page 8 ortex ixer ntroDuction nalog ortex ixer Perating nstructions Your Vortex Mixer is ready for most one-handed applications. The Vortex Mixer 1. Make sure the 3-way rocker switch is in the center, off position. Plug the power operates by mixing tubes just prior to testing. cord into a properly grounded outlet.
- Page 9 & P igital ulsing ortex ixer Perating nstructions Pulse operation: (for Pulsing Vortex Mixer only) 1. Make sure the 3-way rocker switch is in the center, standby position. Plug the power cord into a properly grounded outlet. The unit is now on and in a standby •...
- Page 10 ccessory nstallation nstructions Installing the cup head, 3” head or other head attachments: Installing Vessel Harness: 1. Move the 3-way rocker switch to the center, off/standby position. For the Fixed 1. Install Insert Retainer without foam tube holder onto Vortex Mixer. Speed Vortex Mixer disconnect the power cord from the wall outlet.
- Page 11 ccessory nstallation nstructions Installing Single Tube Holder: 1. Move the 3-way rocker switch to the center, off/standby position. Single Tube Holder should NOT be used on the Fixed Speed Vortex Mixer. 2. Remove cup head, or any other accessory from the Vortex Mixer. 3.
-
Page 12: Troubleshooting
Unit will not run or Motor obstruction problem persists, please contact your VWR representative for repair. Sensor fan misaligned Unit is excessively noisy This error cannot be fixed by the end user. Please contact your VWR representative for repair. or Motor misaligned... - Page 13 ePlacement arts ixeD PeeD ortex ixer escriPtion umber 1. Motor sub assembly 80861480 2. Offset shaft 80854143 3. Pelmor strip 80852441 4. Front panel 80854188 6. Suction cup feet 30532026...
- Page 14 ePlacement arts nalog ortex ixer escriPtion umber 1. Motor sub assembly 80861480 2. Offset shaft 80854143 3. Pelmor strip 80852441 4. Front panel 80854189 6. Suction cup feet 30532026 7. Speed controller 80856108 8. Knob 30532036 9. Rocker switch 30532017 10.
- Page 15 & P ePlacement arts igital ulsing ortex ixer escriPtion umber 1. Motor sub assembly 80861480 2A. Offset shaft - Digital unit 80854143 2B. Offset shaft - Pulsing unit 80854142 3. Pelmor strip 80852441 4A. Front panel - Digital unit 80854190 4B.
- Page 16 ccessories Micro-Tube Holder - Mixes (48) 0.25 to 2mL microtubes. Flat Foam Insert - Ideal for custom applications. Can Requires Insert Retainer. be cut or drilled to fit your specifications. Requires Insert Description Part Number Retainer. Micro-Tube Holder (2 pk) 12620-876 Description Part Number...
- Page 17 ’ ccessories cont Tube Holder Kit 0.5mL Micro-Tube Holder Includes: (1) 9-13mm Tube Holder, (1) 14-19mm Tube Mixes (24) 0.5mL micro-tubes. For use with Single Tube Holder. Holder, (1) 20-25mm Tube Holder, 1 Flat Foam Insert, 2 Part Number 12620-894 Vessel Harness, and 1 Insert Retainer Part Number 58816-130...
Need help?
Do you have a question about the Basic Vortex Mixer and is the answer not in the manual?
Questions and answers