Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Optimum OPTOSAW SQ-V10
Summary of Contents for Optimum OPTOSAW SQ-V10
- Page 1 Operating manual Version 1.0.2 Hand-held metal band saw Item no. 3184210...
- Page 2 Preface Dear customer, Thank you very much for purchasing a product made by OPTIMUM. OPTIMUM metal working machines offer a maximum of quality, technically optimum solutions and convince by an outstanding price performance ratio. Continuous enhancements and product innovations guarantee state-of-the-art products and safety at any time.
-
Page 3: Type Plates
If required, the relevant measures to comply with the country-specific regulations must be taken before commissioning the metal band saw. Always keep this documentation close to the metal band saw. Type plates DE Hand-Bandsäge Optimum Maschinen EN Portable band saw Germany GmbH FR Scie à ruban portative Dr.-Robert-Pfl eger-Str. 26... -
Page 4: Other Pictograms
Symbol Alarm expression Definition / consequence Practical tips and other important or useful information and notes. No dangerous or harmful consequences for people or objects. INFORMATION In case of specific dangers, we replace the pictogram with general danger with a warning of injury to hands, hazardous rotating parts. -
Page 5: Intended Use
If the metal belt saw is used in any way other than described above, modified without authoriza- tion of Optimum Maschinen Germany GmbH, then the metal belt saw is being used improperly. We will not be held liable for any damages resulting from any operation which is not in accord- ance with the intended use. -
Page 6: Residual Risks
Overview of the EMC categories: Categorie C1 required limit values Class B Group 1 according to EN 55011 Categorie C2 Required limit values class A Group 1 according to EN 55011, Installation by EMC experts and warning: “This is a product of category C2 according to EN 61800-3. This product may cause radio interference in a residential area. -
Page 7: Electrical Safety
Keep children and other persons away while using the power tool. If you are distracted, you may lose control of the unit. Electrical safety The connector plug of the power tool must fit into the socket. The plug must not be changed ... -
Page 8: Safety During Operation
Do not use a power tool with a defective switch. A power tool that cannot be switched on or off is dangerous and must be repaired. Unplug and/or remove the battery before making any adjustments, changing any accesso- ries, or putting the unit away. -
Page 9: Personal Protective Equipment
Before starting the sawing work, make sure that the saw blade shows the indicated direc- tion of rotation. Do not start cutting until the saw band has reached its full speed. Do not machine workpieces that are too large or too small for the performance of the ... -
Page 10: Unpacking And Connecting
sqare: 40mm x 40mm rectangular: 30mm x 45mm Saw blade dimension 1140 x13mm x 0.65mm ( standard 10-14 teeth per inch ) Dimensions saw 465 x 280 x 165 mm Noise and vibration Measured values determined according to EN 60745-2-20 and EN 60745- 1+A11 Sound pressure level LpA: 89 dB(A) KpA: 3,0... -
Page 11: Operation
Operation Overview Pos. Designation Pos. Designation Clamping lever Carbon brushes housing Supporting handle Motor housing Speed controller ON Switch with spring return Workpiece - stop surface Saw band Screw Saw blade guide LED On/Off LED light Operating switch WARNING! Before connecting the machine to the mains, always check that the ON switch is not jammed by dirt. -
Page 12: Speed Adjustment
ATTENTION! If the band saw becomes jammed or stuck in the workpiece material during sawing, release the ON switch immediately to prevent damage to the band saw blade and motor. ATTENTION! The band saw is not suitable for use with coolant during the sawing process. Coolant is deposited on the rubberized band rolls and causes the saw band to slip. -
Page 13: Maintenance
4.4.2 LED LED for the lighting. Press the switch (K) to switch on the LED for the lighting. Press the switch again to turn off the backlight. Optionally available saw guide with vice Remove the 3 threaded cover caps from the saw and screw the support arm of the vice to the metal band saw. -
Page 14: Inspection And Maintenance
Inspection and maintenance The company Optimum Maschinen Germany GmbH does not assume any liability and guaran- tee for damages and malfunctions as a result of non-observance of these operating instruc- tions. Use the following for repairs only perfect and suitable tools, ... - Page 15 OPTIMUM GmbH, Robert-Pfleger-Straße 26, D-96103 Hallstadt, does not grant any further warranties unless they are listed below or were promised as part of a single contractual provision. Liability or warranty claims are processed at OPTIMUM GmbH's discretion either directly or through one of its dealers. ...
-
Page 16: Advice For Disposal / Options Of Reuse
V-belts, ball bearings, illuminants, filters, sealings, etc. - Non reproducible software errors Any services, which OPTIMUM GmbH or one of its agents performs in order to fulfil any additional warranty are neither an acceptance of the defects nor an acceptance of its obli- gation to compensate. -
Page 17: Disposal Of The Old Device
Only forward the packaging materials correctly sorted to allow direct reuse. 6.3.3 Disposal of the old device INFORMATION Please take care in your interest and in the interest of the environment that all component parts of the machine are only disposed of in the intended and admitted way. Please note that the electrical devices comprise a variety of reusable materials as well as envi- ronmentally hazardous components. -
Page 18: Ec Declaration Of Conformity
EC - Declaration of Conformity in accordance with the Machinery Directive 2006/42/EC Annex II 1.A The manufacturer / distributor Optimum Maschinen Germany GmbH Dr.-Robert-Pfleger-Str. 26 D - 96103 Hallstadt hereby declares that the following product Product designation: Hand-held metal band saw... -
Page 19: Ersatzteile - Spare Parts
Ersatzteile - Spare parts Ersatzteilbestellung - Ordering spare parts Bitte geben Sie folgendes an - Please indicate the following : Seriennummer - Serial No. Maschinenbezeichnung - Machines name Herstellungsdatum - Date of manufacture Artikelnummer - Article no. ... - Page 20 Ersatzteilzeichnungen - Spare part drawings komplette Säge - complete saw DE | EN SQ-V10 Originalbetriebsanleitung Version 1.0.2 - 2022-09-19...
- Page 21 SQ-V10 Menge Grösse Artikelnummer Pos. Bezeichnung Description Qty. Size Item no. Pos. 1 Hilfsgriff SQ-V10 Auxiliary handle SQ-V10 0318421001 Pos. 2 Schraube SQ-V10 Screw SQ-V10 Pos. 3 Sicherungsmutter SQ-V10 Self-locking nut SQ-V10 Auxiliary handle base SQ- Pos. 4 Hilfsgriffbasis SQ-V10 0318421004 Pos.
- Page 22 SQ-V10 Menge Grösse Artikelnummer Pos. Bezeichnung Description Qty. Size Item no. Pos. 70 Abdeckung Antriebsrad SQ-V10 Drive plate cover SQ-V10 0318421070 Pos. 71 Nadellager SQ-V10 Neddle bearing SQ-V10 0318421071 Sekundäres großes Zahnrad SQ- Secondary large gear wheel Pos. 72 0318421072 SQ-V10 Welle für dreistufiges Ritzel SQ- Shaft for three-stage pinion...
- Page 23 Optionale Sägeführung mit Schraubstock - Optional saw guide with vice SQ-V10 - Optionale Sägeführung mit Schraubstock - Optional saw guide with vice Menge Grösse Artikelnummer Pos. Bezeichnung Description Qty. Size Item no. Wheel Ø65xØ8.3x24 03184210101 Sicherungsring Split washer Ø6 03184210102 Radwelle Roller pin 03184210103...
- Page 24 SQ-V10 - Optionale Sägeführung mit Schraubstock - Optional saw guide with vice Menge Grösse Artikelnummer Pos. Bezeichnung Description Qty. Size Item no. Schraubstockbacken Vise jaw 03184210119 Schraube Screw M10x25 03184210120 Kissen Cushion 03184210121 Schraube Screw M8x30 03184210122 Schraube Screw M4x14 03184210123 Skala Scale...
Need help?
Do you have a question about the OPTOSAW SQ-V10 and is the answer not in the manual?
Questions and answers