Optimum OPTIsaw SQ-V13 Operating Manual

Optimum OPTIsaw SQ-V13 Operating Manual

Metal band saw

Advertisement

Safety
Operating manual
Technical specification
Version 1.0.1
Delivery, interdepartmental
transport and unpacking
Operation
Metal band saw
Maintenance
Appendix
Ersatzteile - Spare parts
Part no. 3194013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OPTIsaw SQ-V13 and is the answer not in the manual?

Questions and answers

Summary of Contents for Optimum OPTIsaw SQ-V13

  • Page 1 Safety Operating manual Technical specification Version 1.0.1 Delivery, interdepartmental transport and unpacking Operation Metal band saw Maintenance Appendix Ersatzteile - Spare parts Part no. 3194013...
  • Page 2 Dear customer, Thank you very much for purchasing a product made by OPTIMUM. OPTIMUM metal working machines offer a maximum of quality, technically optimum solutions and convince by an outstanding price performance ratio. Continuous enhancements and prod- uct innovations guarantee state-of-the-art products and safety at any time.
  • Page 3: Rating Plate

     defines the intended use of the metal band saw,  points out the dangers that might arise for you or others if these instructions are not observed and  informs you about how to avoid dangers. In addition to these operating instructions, please observe ...
  • Page 4: Other Pictograms

    If the metal belt saw is used in any way other than described above, modified without authoriza- tion of Optimum Maschinen Germany GmbH, then the metal belt saw is being used improperly. We will not be held liable for any damages resulting from any operation which is not in accord- ance with the intended use.
  • Page 5: Reasonably Foreseeable Misuse

     obey the operating instructions,  the inspection and maintenance instructions are observed. The right choice of saw band, cutting pressure, cutting speed and coolant is essential to achieve the required cutting performance and angle tolerance. It is forbidden to make any modifications or alternations to the operation values of the metal band saw! They could endanger people and cause damage to the metal belt saw.
  • Page 6 Qualification 1.6.1 Target group private users The machine can be used in the private domain. The acumen of people in the private sector with training in metal working was taken into consideration for creating this operation manual. Vocational training or further instruction in a metal working profession is a prerequisite for safe operation of the machine.
  • Page 7: Safety Check

     injuries due to components or workpieces flying off at high speed,  contact with rotating parts,  fatal electrocution. The metal belt saw features the following safety devices:  Protective cover on the saw bow.  Protective cover on the saw band guide. The saw band of the metal band saw is provided with a protective cover.
  • Page 8: Technical Specification

    1.12 Disconnecting and securing the metal band saw Disconnect the mains plug before starting maintenance and repairs. Technical specification Motor power 400 W Operating mode, duty cycle S6 - 60% Electrical connection 230V / ~50Hz Cutting range 0° round material 125 mm Cutting range 45°...
  • Page 9: Scope Of Delivery

    tion measures are required or not. The following factors influence the actual degree of the noise exposure of the operator:  Characteristics of the working area, e.g. size or damping behaviour,  other noise sources, e.g. the number of machines, ...
  • Page 10: First Commissioning

    Store packed and unpacked parts only under the intended environmental conditions. Follow the instructions and information on the transport box. Consult Optimum Maschinen Germany GmbH if the machine and accessories are stored for more than three months or are stored under different environmental conditions than those spec- ified here.
  • Page 11: Power Supply

    WARNING! When first commissioning the metal belt saw by inexperienced staff you endanger people and the machine. We do not accept any liability for damages caused by incorrectly performed commissioning.  Qualification on page 6 3.5.1 Power supply  Connect the electrical supply cable. ...
  • Page 12  the clamping jaws,  the clamping lever. Place the workpiece to be sawn in the machine vice. Turn the clamping lever (4) to the right until the workpiece is firmly clamped. ATTENTION! Make sure that the workpiece is really clamped. Speed of saw band Set the required saw band speed (2).
  • Page 13: Maintenance

    Saw band tension ATTENTION! Excessive tensioning of the saw blade can lead to a loss of power and to the destruction of components in the saw. Take care not to over-tension the saw band. Observe information on saw band tension. ...
  • Page 14: Inspection And Maintenance

    Only carry out work on the metal band saw if it has been disconnected from the mains power supply. Inspection and maintenance Optimum Maschinen Germany GmbH accepts no liability nor does it guarantee against damage and operating malfunctions resulting from failure to observe these operating instructions. For repairs, only use ...
  • Page 15 Besides the legal liability claims for defects of the customer towards the seller, the manufac- turer of the product, OPTIMUM GmbH, Robert-Pfleger-Straße 26, D-96103 Hallstadt, does not grant any further warranties unless they are listed below or were promised as part of a single contractual provision.
  • Page 16: Advice For Disposal / Options Of Reuse

    - Non reproducible software errors  Any services, which OPTIMUM GmbH or one of its agents performs in order to fulfil any additional warranty are neither an acceptance of the defects nor an acceptance of its obli- gation to compensate. These services neither delay nor interrupt the warranty period.
  • Page 17: Disposal Of Electrical And Electronic Components

    6.3.2 Disposal of new device packaging All used packaging materials and packaging aids from the machine are recyclable and gener- ally need to be supplied to the material reuse. The packaging wood can be supplied to the disposal or the reuse. Any packaging components made of cardboard box can be chopped up and supplied to the waste paper collection.
  • Page 18: Product Follow-Up

    Change information operating manual Chapter Short summary new version number 1.4.1 ; 1.6.1 ; CE 1.4.1 removed ; 1.6.1 target group ; EC declaration update 1.0.1 Product follow-up We are required to perform a follow-up service for our products which extends beyond ship- ment.
  • Page 19: Ersatzteile - Spare Parts

    Ersatzteile - Spare parts Ersatzteilbestellung - Ordering spare parts Bitte geben Sie folgendes an - Please indicate the following :  Seriennummer - Serial No.  Maschinenbezeichnung - Machines name  Herstellungsdatum - Date of manufacture  Artikelnummer - Article no. Die Artikelnummer befindet sich in der Ersatzteilliste.
  • Page 20 SQ-V13 - Sägebügel - Saw bow DE | EN SQ-V13 Originalbetriebsanleitung Version 1.0.1 - 2020-09-30...
  • Page 21 SQ-V13 - Gelenk - Joint SQ-V13 - Antrieb - Drive 175 170 116 138 SQ-V13 DE | EN Version 1.0.1 - 2020-09-30 Originalbetriebsanleitung...
  • Page 22 SQ-V13 - Schraubstock - Vice SQ-V13 - Maschinenunterbau - Machine base DE | EN SQ-V13 Originalbetriebsanleitung Version 1.0.1 - 2020-09-30...
  • Page 23 Ersatzteilliste Bohrkopf - Spare part list Menge Grösse Artikelnummer Pos. Bezeichnung Designation Qty. Size Item no. Zylinderstift Cylindrical pin 5x14 Platte Plate 0319401303 Skala Scale 0319401304 Innensechskantschraube Hexagon socket screw M8x16 Federscheibe Spring washer Schraube Screw M5x10 Fuss Foot 0319401308 Schraube Screw M5x10...
  • Page 24 Scheibe Washer Sechskantmutter Hexagon nut Stange 0319401364 Skala Scale 0319401365 Sägebügel Saw bow 0319401366 Welle Shaft 0319401367 Platte Plate 0319401368 Führung guiding 0319401369 Innensechskantschraube Hexagon socket screw M8x25 Gewindestift Grub screw M8x16 Laufrad Wheel 0319401372 Kugellager Ball bearing 6201 0406201R Sicherungsring Retaining ring Scheibe...
  • Page 25 Scheibe Washer Nocken Cams 03194013136 Feder Spring 03194013137 Kugellager Ball bearing 03194013138 Kugellager Ball bearing 03194013139 Sechskantmutter Hexagon nut Gehäuse Housing 03194013141 Ein-Aus-Schalter On-Off switch MB-KJD12-14 03194013145 Motor Engine 03194013160 Kugellager Ball bearing 6202 0406202R Dichtung Seal 12-24-7 03194013175 Schraube Screw M5x25 Gehäuse...
  • Page 26: Ec Declaration Of Conformity

    EC - Declaration of Conformity according to Machinery directive 2006/42/EC, Annex II 1.A The manufacturer/  Optimum Maschinen Germany GmbH Distributor: Dr. Robert-Pfleger-Str. 26 D - 96103 Hallstadt hereby declares that the following product Product designation: Metal band saw Type designation:...

Table of Contents