Advertisement
Product Installation Guidelines
®
CliniLever
Sink Set Swivel Taps
PRODUCT CODES:
- 102.15.21.03
- 102.15.11.03
SPECIFICATIONS
−
®
The CliniLever
product range is primarily used for hand washing applications in medical facilities, hospitals,
aged care facilities, schools and in-home care.
−
®
CliniLever
products provide state of the art features to comply with the latest healthcare guidelines.
−
The dual levers are easy to access and operate which simplifies hand washing.
−
®
All CliniLever
range is laminar flow (not aerated).
−
Our highly sought after lever handle design can be operated with elbows or wrists to avoid hand contact.
−
The main body is made of solid dezincification resistant (DR) brass rod, with a DR brass gooseneck outlet.
Quick action SBA's include brass jumper valve / ceramic disc components, with red and blue indicator buttons on
−
80mm or 150mm lever action handles.
Lead Safe™ brass construction. *
IMPORTANT: All CliniLever
in good working order.
*Our Lead Safe™ product range is compliant with the Lead-Free Requirements of the NCC 2022 Vol. Three, Clause A5G4(2) and NSF/ANSI 372.
**
Any flow controller incorporated in the outlet to be tightened to prevent removal by hand. As Per AS3718.
WARNINGS: Special attentions to be paid on notes, photos, images, or drawings of assembly
steps marked with the warning symbol.
TECHNICAL DATA
Inlet
Outlet
Headwork
Working Pressure Range (kPa)
Working Temperature Range (°C)
Nominal Flow Rate (LPM)
Finish
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice
TOOLS REQUIRED
− Power drill, spanner or adjustable crescent
− Copper tube cutter
© Galvin Engineering Pty Ltd
CP-BS Lead Safe™ Hospital
- 102.15.12.03
- 102.15.22.03
®
healthcare taps are tested in accordance with AS/NZS 3718 and leave our premises
Version 1, 11 June 2024, Page 1 of 5
½" Cu/BSP
Laminar Flow
Jumper Valve / Ceramic Disc
Min
50
Max
500
Min
5
Max
65
5.15
Chrome
Document No.: 001.00.10.20
Advertisement
Table of Contents
Related Manuals for Galvin Engineering CliniLever CP-BS Lead Safe 102.15.21.03
Summary of Contents for Galvin Engineering CliniLever CP-BS Lead Safe 102.15.21.03
- Page 1 Working Temperature Range (°C) Nominal Flow Rate (LPM) 5.15 Finish Chrome NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without notice TOOLS REQUIRED − Power drill, spanner or adjustable crescent − Copper tube cutter © Galvin Engineering Pty Ltd...
-
Page 2: Pre-Installation
INSTALLATION IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these provisions shall void the product warranty and may affect the performance of the product. - Page 3 Open the lever handles and ensure that there is flow from both hot and cold inlets. − Secure the handles in position using the supplied − Inspect the tap and check for any leaks stainless steel cap screws and washers. © Galvin Engineering Pty Ltd...
-
Page 4: Troubleshooting
Replace the cartridge and hand tighten back into re-grease with potable water approved grease. the body. Re-assemble top assembly. Follow the product Follow the product installation guidelines for the installation guidelines for the relevant product re- relevant product re-assembly method. assembly method. © Galvin Engineering Pty Ltd... -
Page 5: Warranty
Version 1, 11 June 2024, Page 5 of 5 WARRANTY Galvin Engineering products are covered under our Manufacturer's Warranty. Galvin Engineering products must be installed in accordance with the installation instructions and in accordance with AS 3500 and NCC Volume Three, relevant Australian Standards and local authorities applicable to product being installed.
Need help?
Do you have a question about the CliniLever CP-BS Lead Safe 102.15.21.03 and is the answer not in the manual?
Questions and answers