Related Manuals for Bender HMI140
Summary of Contents for Bender HMI140
- Page 1 Manual HMI140 / HMI145 / HMI150 Interface modules for Bender charge controllers HMI1xx_D00481_00_M_XXEN/11.2023...
- Page 2 HMI1xx_D00481_00_M_XXEN/11.2023...
-
Page 3: Table Of Contents
HMI140 / HMI145 / HMI150 Table of contents General information................... 5 How to use the manual..........................5 Indication of important instructions and information...............5 Signs and symbols............................5 Service and Support............................5 Training courses and seminars........................6 Delivery conditions............................6 Inspection, transport and storage......................6 Warranty and liability.............................6... - Page 4 Table of contents Declarations of conformity........................21 Ordering information...........................21 HMI1xx_D00481_00_M_XXEN/11.2023...
-
Page 5: General Information
Protect from dust Temperature range Recycling RoHS directives Service and Support Information and contact details about customer service, repair service or field service for Bender devices are available on the following website: Fast assistance | Bender GmbH & Co. KG. HMI1xx_D00481_00_M_XXEN/11.2023... -
Page 6: Training Courses And Seminars
Regular face-to-face or online seminars for customers and other interested parties: www.bender.de > know-how > seminars. Delivery conditions The conditions of sale and delivery set out by Bender GmbH & Co. KG apply. These can be obtained in printed or electronic format. The following applies to software products: ‘Software clause in respect of the licensing of standard software as part of deliveries,... -
Page 7: Disposal Of Bender Devices
HMI140 / HMI145 / HMI150 Disposal of Bender devices Abide by the national regulations and laws governing the disposal of this device. For more information on the disposal of Bender devices, refer to www.bender.de > service & support. 1.10 Safety If the device is used outside the Federal Republic of Germany, the applicable local standards and regulations must be complied with. -
Page 8: Device-Specific Safety Instructions
Device-specific safety instructions Device-specific safety instructions ADVICE The HMI1xx complies with the relevant harmonized standards to ensure that the requirements of the Radio Equipment Directive (see chapter “Declarations of conformity”, page 21) are met. It is the responsibility of the distributor of the complete system to ensure conformity with this and any additional legal requirements. -
Page 9: Function
USB cable. The module must only be used in combination with charge controllers* from Bender GmbH & Co. KG that support the operation of the HMI module. Any other use than that described in this manual is regarded as improper. -
Page 10: Sensors
Function 3.3.2 Sensors An integrated light sensor is provided to enable adaptation of the light intensity of the LEDs to the brightness of the surroundings. The HMI module is equipped with an integrated temperature sensor to avoid any thermal damage. The sensors are read and the corresponding reaction takes place via the charge controller that is connected. -
Page 11: Functional Description
HMI140 / HMI145 / HMI150 USB host outputs The two USB host outputs of the HMI module are connected to a USB host output of the charge controller via an internal USB hub. They support communication or data exchange in accordance with the functional description of the charge controller in use. -
Page 12: Dimensions And Mounting
Dimensions and mounting Dimensions and mounting Dimensions Dimension diagram Dimensions in mm HMI1xx_D00481_00_M_XXEN/11.2023... -
Page 13: Mounting
HMI140 / HMI145 / HMI150 Mounting Ambient light sensor Temperature sensor Red marks: possible fastening points Either the inner or the outer fastening holes can be used. Fastening recommendation, Ø3.1: • Screws: 2.5 mm • Head: max. 5 mm • Extension studs: 5.1 mm •... -
Page 14: Connection
Connection Connection Definition of connections Terminal Description USB type A: 2 x USB host USB type B: Charge controller (controller interface, 5 V supply) Phoenix Contact PCB terminal, 8-pole: Additional DC supply, FE, relay switching contacts, control input Phoenix Contact PCB terminal, 8-pole: External RGB LEDs LEDs can be connected without series resistors (constant current control) Voltage supply connection... -
Page 15: Connection Assignment, Terminals C And D
HMI140 / HMI145 / HMI150 Connection assignment, terminals C and D Terminal C: Phoenix Contact DMC 1.5/ 4-G1-3.5 P26THR R44 (2x4-pole) Description Description DC supply voltage input Ground of the voltage supply and control signals Functional earthing FE input (EMC functional earthing) - Page 16 Connection Examples for connecting the external RGB LED outputs Example 2: Example 1: LED Two LEDs per with shared channel with cathode shared anode HMI1xx_D00481_00_M_XXEN/11.2023...
-
Page 17: Commissioning
HMI140 / HMI145 / HMI150 Commissioning It is preferable to operate the HMI module with a DC supply voltage to prevent overloading of the USB supply. ADVICE If supply of the HMI module is possible exclusively via the USB interface, the availability of individual... -
Page 18: Technical Data
Voltage range Max. power consumption without USB load 3.5 / 7.5 / 9.5 W HMI140 / 145 / 150 Max. power consumption with USB load HMI145 / 150 14.0 / 16.0 W DC 5 V from charge controller (terminal B) - Page 19 HMI140 / HMI145 / HMI150 Channel bandwidth 20 MHz Data rates 802.11b 1, 2, 5.5, 11 Mbps 802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n MCS0-MCS7 (max. 72.2 Mbps) Max. output power 19 dBm EIRP Inputs Control input (terminal C: IN) Input voltage DC 0…15.8 V...
-
Page 20: Approvals
Technical data Transport (IEC 60721-3-2) Long-term storage (IEC 60721-3-1) 1M12 EMC environmental classes Emitted interference B (residential, business or commercial areas) Interference immunity A (industrial environment) Connection lengths / cable types USB host A1 and A2 Max. cable length 1.8 m Cable type Double shielded Charge controller connection (terminal B) - Page 21 Declarations of conformity EU Declaration of conformity Hereby, Bender GmbH & Co. KG declares that the device covered by the Radio Directive complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://www.bender.de/fileadmin/content/Products/CE/CEKO_HMIxxx.pdf...
- Page 22 Alle Rechte vorbehalten. 35305 Grünberg Nachdruck und Vervielfältigung nur mit Germany Genehmigung des Herausgebers. © Bender GmbH & Co. KG, Germany Subject to change! The specified Tel.: +49 6401 807-707 All rights reserved. standards take into account the edition emobility@bender.de Reprinting and duplicating only with valid until 11.2023 unless otherwise...
Need help?
Do you have a question about the HMI140 and is the answer not in the manual?
Questions and answers