Humidity/Steam Setting; Dryer Function; Second Cooking Step Activation - TECNOEKA TOUCHSCREEN MKF D1T Original Operating And Instruction Manual

clear text) If you keep your finger on the same icons, the value of the parameter increases or
decreases quickly. To confirm the set value, tap t h e i c o n ( i n g r e e n )
.
The parameter value must be set within 15 seconds.
To stop the setting procedure and return to the initial temperature value, tap the icon (in red) .

2.8.3 HUMIDITY/STEAM setting

To activate the "humidity/steam" function (with display active), tap the symbol
.
If the display shows (in yellow) the functional status of "PREHEATING", the function can only be activated
manually. Simply touch and hold your finger on the symbol for the desired time to produce
humidity/steam. If, on the other hand, the display shows (in red) the functional status of "COOKING", each
time you tap the symbol an automatic humidification/steam cycle is activated: made up of 3 operating
phases ("Cycles") which last 2 seconds ("T On") each and are spaced 10 seconds apart ("T Off").
To change the timing of the humidification/steam cycle (with the oven running), touch the symbol for at
least 3 seconds : t h e " s t e a m " s c r e e n i s d i s p l a y e d w i t h t h e w r i t i n g ( i n g r e e n ) " T
O n 2 s " ( s t e a m a c t i v a t i o n t i m e ) . T a p t h e i c o n ( i n g r e e n ) : the digit (in yellow) of
the seconds can be changed (up to 99 seconds). The value increases by tapping the icon (in clear
and decreases by tapping the icon (in clear text) . Holding your finger on the same
text)
icons, the value of the parameter increases or decreases quickly.
To confirm your choice, tap
t h e i c o n a g a i n ( i n g r e e n ) or wait 15 seconds (automatic
confirmation). Tap the icon (in clear text) and the digits (in green) of "T Off" can be changed (up
to 999 seconds) by acting as before to change the digits of "T On". Tap the icon (in clear text) and
the digits (in green) of the "Cycles" can be changed (up to 20 cycles) by acting as before to change the
digits of "T On".

2.8.4 DRYER function

To activate the "dryer" function (with active display), tap the symbol (illuminated symbol = steam vent
opening). To deactivate the function, tap the symbol again (dark symbol = steam vent closing).
If the functional status of the oven is in "PREHEATING" mode or in "READY" mode, you can set a time for
opening the steam vent for the last cooking step.
Touch the symbol for at least 3 seconds: the "Vent" screen appears with any operating mode
("Status") already present.
The "opn" writing (in green) indicates that the vent remains open during the entire cooking cycle and for a
further 10 seconds after the end of the cycle.
The "clo" writing (in green) indicates that the vent is always closed.
The message (in green) "minutes/seconds" of the "Time" indicates that the vent remains open during the
last minutes/seconds of the cooking step: for the set time.
To set/change the vent opening time, tap t h e i c o n ( i n g r e e n )
: the digit (in yellow) of the
minutes can be changed (up to 99 minutes) . The value increases by tapping the icon (in clear text) ,
decreases by tapping the icon (in clear text) If you keep your finger on the same icons, the value of
the parameter increases or decreases quickly.
To confirm your choice, tap t h e i c o n a g a i n ( i n g r e e n )
: the display shows the digits (in yellow)
of the seconds. To change (up to 50 seconds) and confirm the value, use the icons as before to change and
confirm the minutes value. The parameter value must be set within 15 seconds.
If the "Time" of opening the vent (0'00") is cancelled, it is possible to switch from one "Status" (operating
mode) to the other by tapping the icon (in clear text) or the icon (in clear text) .
To stop the setting procedure and return to the initial values, tap the icon (in red) .

2.8.5 SECOND Cooking STEP ACTIVATION

After setting a FIRST cooking step ("ph 1/2") with the operating parameters and related values, you can
also activate a SECOND step (with active display).
Touch the symbol for at least 3 seconds: the "Expert" screen appears.
By tapping the icon (in clear text) the "Add phase" option (written in green) can be selected.
10