Download
Share
Print this page
Toro GeoLink 131-7260 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Paint Sprayer
  5. GeoLink 131-7260
  6. Installation instructions manual
Toro GeoLink 131-7260 Installation Instructions Manual

Toro GeoLink 131-7260 Installation Instructions Manual

Spray system finishing kit
Hide thumbs

Advertisement

Quick Links

Download this manual
GeoLink
Serial Number 315000000-315999999 Multi Pro
Model No. 131-7260
The GeoLink™ spray system kit is an attachment for a turf spray application vehicle and is intended to be used by professional,
hired operators in commercial applications. It is designed primarily for spraying on well-maintained lawns in parks, golf
courses, sports fields, and on commercial grounds.
You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information,
help finding a dealer, or to register your product.
This product contains a chemical or chemicals known to the State of California to
Use of this product may cause exposure to chemicals known to the State of California
Safety
WARNING
Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals,
plants, soils, or other property.
• Carefully read and follow the chemical warning labels and material safety data sheets (MSDS) for all
chemicals used and protect yourself according to the chemical manufacturer's recommendations. For
example, use appropriate personal protective equipment (PPE), including face and eye protection,
gloves, or other equipment to guard against personal contact with a chemical.
• There may be more than 1 chemical used and information on each chemical should be assessed.
• Refuse to operate or work on the sprayer if this information is not available.
• Before working on a spray system, clean the machine ensure that the spray system has been triple
rinsed and neutralized according to the recommendations of the chemical manufacturer(s) and that all
the valves have been cycled 3 times.
• Verify that there is an adequate supply of clean water and soap nearby, and immediately wash off any
chemicals that contact you.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Spray System Finishing Kit
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
to cause cancer, birth defects, or other reproductive harm.
Register at www.Toro.com.
WARNING
CALIFORNIA
Form No. 3412-187 Rev B
®
5800 Turf Sprayer
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3412-187* B
Printed in the USA

Advertisement

loading
Need help?

Need help?

Do you have a question about the GeoLink 131-7260 and is the answer not in the manual?

Questions and answers

Related Manuals for Toro GeoLink 131-7260

Summary of Contents for Toro GeoLink 131-7260

  • Page 1 It is designed primarily for spraying on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
  • Page 2 Prepare to install the kit. Disconnect the rear wire harness from – No parts required the optional attachment. Switch plug (pivoting hose reel kit—Toro Disconnect the optional pivoting hose Part No. 99-7420) reel kit. Tube assembly (Toro Part No. 114-9553) Disconnect the optional foam-marker kit.
  • Page 3 Procedure Description Qty. Flow meter Flange clamp 76 mm (3 inches) Gasket (2-1/4 inch outside diameter) Reducer adapter Flange clamp 51 mm (2 inches) Gasket (1-5/16 inch outside diameter) Barbed-flange fitting (1 inch) Install the flow meter and pressure transducer. Hose (1 x 7-1/4 inches) Hose clamp Pressure transducer and manifold...
  • Page 4 No parts required Connect the ultra sonic boom kit. Cover extension assembly (12-nozzle—Toro Part No. 120-0621) Pop rivet (Toro Part No. 114439) Support bracket (center section cover—Toro Part No. 131-3703-03) Clip nut (Toro Part No. 94-2413) Assemble the optional covered-boom Flange-head bolt (3/8 x 1-1/4 kit.
  • Page 5 Procedure Description Qty. – No parts required Connect the optional tank rinse kit. Complete the installation of the GeoLink – No parts required spray system finishing kit. Disconnecting the Battery WARNING Electrical sparks can cause the battery gasses to Preparing to Install the Kit explode, resulting in personal injury.
  • Page 6 Disconnecting the Rear Wire Harness from the Optional Attachments No Parts Required g029414 Figure 2 Disconnecting the Pivoting 1. Positive battery cable 3. Negative battery post 2. Positive battery post 4. Negative battery cable Hose-Reel Kit 1. At the back of the machine, locate the wire harness 2.
  • Page 7 Disconnecting the Compressor for the Foam Marker Kit 1. At the back of the foam-marker tank, locate the wire harness at the compressor (Figure g030425 Figure 5 2. Disconnect the 6-pin connector of the rinse-pump harness from the 6-socket connector of the rear main harness (Figure g030422...
  • Page 8 Parts needed for this procedure: where you removed the switch (Figure 6. Insert the switch plug into the control box until the Switch plug (pivoting hose reel kit—Toro Part No. 99-7420) plug snaps into the cover securely (Figure 7. Align the control box to the reel-mounting plate...
  • Page 9 g031472 Figure 8 g031488 Figure 9 1. Compression 6. Cable tie 1. Tubing—foam-marker 3. R-clamp fitting—water (right boom nozzle (right boom section) section—blue tube) 2. Tubing—foam-marker 2. Compression fitting—air 7. Compression nut—water nozzle (left boom section) (right boom section—clear (right boom section—clear tube) tube) 3.
  • Page 10 6. Align the old liquid and air tubes (Figure 12) to the new boom section shown) tube assembly (Toro Part No. 114-9553). 2. At the foam-marker nozzle, loosen the compression nut that secures the blue tube (water) to the blue compression fitting of the foam-marker nozzle (Figure 11).
  • Page 11 7. Use a piece of tape to mark the length of the old liquid 4. Route the tube assembly along the rear side of the and air tubes onto the new tube assembly. upper support pole of the outer boom section as shown in Figure 8.
  • Page 12 7. Loosely secure the free end of the tube assembly to the 3. Disconnect the 2-socket connectors of the wire harness outer boom section. for the sonic boom finishing kit (Figure 17) from the 2-pin connectors of the solenoids of the lift-cylinder 8.
  • Page 13 Disconnecting the Ultra-Sonic Sensor Cable from the Wire Harness Removing the Center 1. Disconnect the 3-socket connector of the sonic boom wire harness from the 3-pin connector of the cable for Section Cover (11-nozzle) of the right ultra-sonic sensor (Figure the Optional Covered-Boom No Parts Required Procedure...
  • Page 14 Removing the Undercarriage Shroud No Parts Required g032030 Figure 20 Procedure 1. Center section cover G032041 g032041 Figure 21 1. Remove the 7 flange-head bolts (5/16 x 7/8 inch) and 7 washers (5/16 inch) that secure the rear of the undercarriage shroud to the chassis of the machine (Figure 22).
  • Page 15 g032043 Figure 23 1. Engine mount 4. Flange locknuts (5/16 inch) 2. Bolt—shown for clarity; do 5. Front of the machine not remove 3. Support straps (undercarriage shroud) 3. Lift the support straps over the bolts that secure the undercarriage shroud to the engine-mount brackets. 4.
  • Page 16 Disconnecting the Pressure-Sense Tube for the Dash Gauge No Parts Required g033073 Disconnecting the Pressure-Sense Tube for the Dash Gauge Machines Without an Optional Hose Reel Kit Note: If your machine is equipped with an optional spray gun kit, refer to Disconnecting Pressure-Sense Tube and Supply Hose (page 17).
  • Page 17 Disconnecting Pressure-Sense 2. Pull the pressure-sense tube for the dash gauge out of the tube coupler (Figure 26 Figure 27). Tube and Supply Hose Note: Do not remove the 90° elbow for the shutoff Optional Spray Gun Kit or Optional Pivoting valve for the supply hose of the hose reel from the Hose Reel Kit flange of the right boom-section valve.
  • Page 18 Removing the Rear Wire Harness for the Machine Parts needed for this procedure: Rear wire harness Disconnecting the Front and Rear Wire Harnesses Note: Use a machine hoist when disconnecting the front and rear wire harnesses. g032051 Figure 28 1. Front of the machine 2.
  • Page 19 g032177 Figure 33 g032173 Figure 29 1. 2-pin connector—hose 3. Front of the machine 1. 10-socket 3. Front of the machine reel (front harness) connector—sprayer-harness 2. 2-socket connector—hose interconnect (front reel (rear harness) harness) 2. 10-pin connector—sprayer-harness interconnect (rear harness) g032178 Figure 34 1.
  • Page 20 Disconnecting the Connectors for 3. Remove the fir-tree anchors that secure the rear wire harness to the holes at the forward side and lower plate the Components of the manifold mount (Figure 38). 1. At back of the machine (between the right frame tube and the right fender) disconnect the 3-pin connector of the speed-sensor harness at the right hydraulic-traction motor from the 3-socket connector of the rear, main...
  • Page 21 g030875 g030459 Figure 41 Figure 39 1. Sprayer pump 3. Rear wire harness 1. Right—up (solenoid and 4. Enable (solenoid and 2. Rear cross tube 4. Fir-tree anchor main-harness connector) main-harness connector) 2. Left—up (solenoid and 5. Right—down (solenoid main-harness connector) and main-harness 7.
  • Page 22 4. Align the switch plug to the opening in the dash panel where you removed the rate switch (Figure 43). 5. Insert the switch plug into the dash panel until the plug snaps into the panel securely (Figure 43). Removing the Rate-Control Switch Parts needed for this procedure: Removing the...
  • Page 23 g032316 Figure 45 1. Adapter coupling (at the 4. Gasket g032455 agitation valve) Figure 46 2. Adapter coupling (at the 5. Flange clamp left boom-section valve) 1. Flange (left boom-section 3. Flange clamp 76 mm (3 valve) inches) 3. Straight coupling 2.
  • Page 24 Removing the Shutoff Valve and 4. Repeat steps through for the supply hose at the other outer boom section. Bypass Hoses 5. Under the center boom section, remove the hose clamp 1. At the lower end of the upper bypass hose, remove that secures the supply hose for the boom section to the flange-head bolt (5/16 x 3/4 inch), washer (5/16 the barbed T-fitting...
  • Page 25 Note: Retain the 90° barbed fitting and 2 clamps for 7. Remove the upper and lower bypass hoses from the installation in steps and 9. machine (Figure 54). 4. Remove the hose clamps that secure the drain-valve Note: You no longer need the shutoff valve, T-fitting, hose and the rear tank-drain hose to the barbed upper bypass hose, and lower bypass hose.
  • Page 26 Removing the Valve Actuator 1. Remove the retainer that secures the a actuator to the manifold valve of the section valve assembly(Figure 56). Note: Squeeze the 2 legs of the retainer together while pushing it down. Note: Retain the actuator and retainer for installation in steps Replacing the Bypass Valves from the Section Valves with Caps (page...
  • Page 27 6. Align the coupler of the section valve actuator that you 3. Remove the boom-section valves from the manifold removed in step Removing the Valve Actuator mount and set aside the valves (Figure 60). (page 26) with the stem port of the manifold valve Note: Retrain the boom-section valves, flange-head (Figure 59).
  • Page 28 Note: Protect the boom-lift manifold and the 4. Remove the flange locknut (5/16 inch) and flange-head hydraulic cylinder from dust and debris by plugging bolt (5/16 x 3/4 inch) that secures the pivot pin to the extend and retract ports. cylinder mount (Figure 64).
  • Page 29 Removing Boom-Lift Manifold from the Center Boom Section 1. At port P of the boom-lift manifold, mark the pressure hydraulic hose with a cable tie (Figure 66). g030525 Figure 65 1. Pivot fitting (outer boom 4. Pivot pin section) 2. Nylon-flange bushing 5.
  • Page 30 g032513 Figure 68 1. Support brackets (center 3. Flange-head bolt (1/2 x boom section) 1-1/4 inches) and flange locknut (1/2 inch) 2. Mounting channels 4. Tape mark g033152 Figure 67 (machine) 1. Boom-lift manifold 4. Support bracket (boom-lift manifold) 4. Remove the 4 flange-head bolts (1/2 x 1-1/4 inches) 2.
  • Page 31 Installing the Center Boom Extension Parts needed for this procedure: Flange-head bolt (3/8 x 1 inch) Flange locknuts (3/8 inch) Center boom extension Cylinder mount (wide) g030671 Figure 71 Tie plate (wide) Carriage bolt (1/2 x 1-1/4 inches) 1. Flange locknut (5/16 inch) 3.
  • Page 32 bracket to the center boom section, and remove the bracket (Figure 73). g032429 Figure 73 1. Flange-head bolt (3/8 x 1 4. Flange locknut (3/8 inch) inch) 2. Center boom section 5. Left support bracket (center boom section) 3. Right support bracket g030591 Figure 72 (center boom section)
  • Page 33 2. Remove the 2 carriage bolts (1/2 x 1-1/4 inches) and you removed in step Separating the Center Boom 2 locknuts (1/2 inch) that secure the narrow cylinder Section Trusses (page 32). mount, left and right truss frames, and narrow tie plate 3.
  • Page 34 4. Repeat steps for the left support bracket at the left truss frame (Figure 78). 5. Torque the flange-head bolts and flange nuts to 37 to 45 N∙m (27 to 33 ft-lb). Installing the Mount Assembling the Sprayer Nozzles Brackets and Sprayer and Hoses for the Center Boom Nozzles to the Center Boom Section...
  • Page 35 Installing the Sprayer Nozzles and Hoses to the Center Boom Section 1. Route the hose 13 mm (10 inches) and nozzle assembly between the truss braces of the outer truss (Figure 81). g032438 Figure 80 1. Hose 13 x 250 mm (1/2 x 3.
  • Page 36 6. Align the hex-head bolt (5/16 x 3/4 inch) of the sprayer nozzle through the hole in the nozzle mount (Figure 82) and loosely secure the nozzle to the mount with a flange locknut (5/16 inch) that you removed in steps Removing the Sprayer Nozzles (page 31).
  • Page 37 Installing the Flow Meter and Pressure Transducer onto the Machine Installing the New Center 1. Align the gasket (2-1/4 inches) that you removed in step Removing the Connector Tube and Reducer Boom Section Adapter (page 22)between the flow meter and the reducer adapter that is installed at the right side of the master-control valve (Figure...
  • Page 38 3. Torque the bolts and nuts to 234 to 286 N∙cm (21 to 25 to in-lb). Assembling the Valve Mount and Installing the Valve Mount Sprayer Valve Assembly to the and Sprayer Valves Machine Lifting equipment capacity: 23 kg (50 lb) Parts needed for this procedure: 1.
  • Page 39 5. Torque the flange-head bolts and flange locknuts to 1978 to 2542 N∙cm (175 to 225 in-lb). Assembling the Hose to the Sprayer Valve Manifold 1. Assemble the hose (1 x 8-1/2 inches) over the 90° flange fitting (1 inch) as shown in Figure g032539 Figure 88...
  • Page 40 Assembling Sprayer Valves 8, 9, and 10 to the Valve Mount Important: The left boom-section valve that you removed in step Disassembling the Boom-Section Valves from the Manifold Mount (page 27) is identified as nozzle-valve 8, the center boom-section valve is identified as nozzle-valve 9, and the right boom-section valve is identified as nozzle-valve 10 for the remainder of the GeoLink finishing kit installation instructions.
  • Page 41 g030769 Figure 94 1. Lift cylinder (fixed end)) 4. Flange-head bolt (5/16 x g033189 Figure 93 3/4 inch) 2. Pivot pin 5. Cylinder mount 5. Hydraulic-pressure hose 1. Support bracket and boom-lift manifold (marked with a cable tie) 3. Flange locknut (5/16 inch) 2.
  • Page 42 Installing the Lift-Cylinder Hoses 1. Loosely assemble a new hydraulic hose (1/4 x 24-3/4 inches) between the extend port of the left boom-lift cylinder and port C3 of the boom-lift manifold (Figure 95). g030773 Figure 96 1. Port C1 (boom-lift 4.
  • Page 43 the body of each of the sprayer nozzle, and remove the barbed-hose shanks (Figure 98). Note: The hex-head bolt (5/16 x 3/4 inch—stainless steel) will separate from the upper clamp half when you Installing the Outer Boom open the clamp, retain the bolt for installation. Sections Parts needed for this procedure: Nylon-flange bushing...
  • Page 44 g030783 g030789 Figure 99 Figure 101 1. Nylon-flange bushing 2. Pivot fitting (outer boom 1. Hairpin 3. Clevis pin section) 2. Rod end (lift cylinder) 4. 25 mm (1 inch) hole—horn of the pivot-fitting 3. Align the busings in the pivot fitting with the holes in the flanges of the pivot bracket at the end of the center 7.
  • Page 45 Installing the Sprayer-Nozzle Hoses Parts needed for this procedure: Supply hose—279 cm (110 inches) Supply hose—234 cm (92 inches) Supply hose—188 cm (74 inches) Supply hose—81 cm (32 inches) Identifying the Sprayer-Nozzle Hose Positions Identify the supply hoses by length (Figure 102) for each of the sprayer-nozzle position as follows: Sprayer nozzle hose-position table...
  • Page 46 g033192 Figure 102 1. Supply hose 279 cm (110 5. Supply hose 188 cm (74 9. Supply hose 81 cm (32 inches)—sprayer nozzle 1 inches)—sprayer nozzle 9 inches)—sprayer nozzle 5 and 2. Supply hose 188 cm (74 6. Supply hose 279 cm (110 10.
  • Page 47 Assembling the Hoses to Nozzle 7. Assemble the straight barbed fitting of a supply hose 188 cm (74 inches) onto the coupler of nozzle valve Valves 1 through 4 (Figure 103). 1. Assemble the straight barbed fitting of a supply hose Note: Ensure that the barbed fitting fully seats onto 279 cm (110 inches) onto the coupler of nozzle valve the coupler.
  • Page 48 Assembling the Hoses to Nozzle 7. Assemble the straight barbed fitting of a supply hose 279 cm (110 inches) onto the coupler of nozzle valve Valves 7 through 10 (Figure 105). 1. Assemble the straight barbed fitting of a supply hose Note: Ensure that the barbed fitting fully seats onto 188 cm (74 inches) onto the coupler of nozzle valve the coupler.
  • Page 49 3. Route the supply hoses 279 cm (110 inches) and barbed-hose shanks (3/4 inch) along the boom section to sprayer nozzles 1 and 10 as shown in (Figure 106 Figure 107). 4. Route the supply hoses 234 cm (92 inches) and barbed-hose shanks (3/4 inch) along the boom section to sprayer nozzles 2 and 9 along the boom section as shown in...
  • Page 50 Assembling the Rear Wire Harness to the Machine Parts needed for this procedure: Rear wire harness Cable tie Routing the Wire Harness Along the Frame Tube 1. Locate the 165 cm (65 inches) branch and the 203 cm (80 inches) branch of the new electrical harness (Figure 110).
  • Page 51 g030874 Figure 112 1. Rear wire harness—203 3. Front of the machine cm (80 inches) branch 2. Right frame tube 4. Fir-tree anchors and cable tie locations 4. Insert the fir-tree anchors of the 203 cm (80 inches) branch of the rear wire harness into the holes in the right frame tube (Figure 112) where the fir trees of...
  • Page 52 g032188 g032185 Figure 116 Figure 114 1. Front wire harness 4. Rear wire harness 1. Front wire harness 3. Rear wire harness 2. 8-pin 5. Front of the machine 2. 3-socket connector—not 4. Front of the machine connector—sprayer-harness used (flow meter—front interconnect (front harness) harness)
  • Page 53 g033232 Figure 120 g032189 1. 4-socket connector (rear 3. 1-socket connector (rear Figure 118 wire harness) wire harness) 1. Front wire harness 4. Rear wire harness 2. Top of the machine 4. Front of the machine 2. 2-pin connector—hose 5. Front of the machine reel (front harness) 3.
  • Page 54 2. Assemble the mounting bracket to the engine with the 3 flange head bolts and 1 flange nut that you removed in step 8 Removing the Engine-Control Module and Mounting Bracket (for Machines with a Gasoline Engine Only) (page 15); tighten the bolts and nuts by Installing the hand.
  • Page 55 3. Assemble the undercarriage shroud to the engine-mount brackets and bolts (Figure 123) with the 4 flange locknuts (5/16 inch) that you removed in step 7 Removing the Undercarriage Shroud (page 14). Connecting the Rear Wire 4. Align the holes in the rear part of the undercarriage shroud with the holes in the chassis (Figure 124).
  • Page 56 Routing the Wire Harness at the Routing the Wire Harness for the 10-Valve Mount Sprayer Pump 1. Route the 203 cm (80 inches) wire harness branch 1. Route the 86 cm (34 inches) wire harness branch for across the back of the 10-valve mount with the 10 the spray-pump solenoid across the top of the sprayer connectors for the nozzle valves rearward and below frame channel and down toward the sprayer-pump...
  • Page 57 Connecting the Wire Harness to the Manifold Mount Components 1. Route the connectors of the 203 cm (80 inches) wire harness branch labeled Flow Meter and Pressure Transducer rearward of the manifold mount (Figure 128). g031039 Figure 129 1. Agitation valve 3.
  • Page 58 Connecting the Wire Harness to the Solenoids for the Lift-Cylinder Manifold 1. At the bottom of the lift-cylinder manifold, connect the 2-socket connector of the rear wire harness labeled Enable Solenoid into the 2–pin connector for the enable solenoid (Figure 131 Figure 132).
  • Page 59 Connecting the Wire Harness to Connecting the Wire Harness to the Sprayer Valves the Sprayer Pump and the Speed Sensor 1. Route the 3-socket connectors of the 203 cm (80 inches) wire harness branch with labels Nozzle Valve 1. At the back of the machine (inboard of the sprayer 1 through Nozzle Valve 5 rearward of the 10-valve pump), connect the 2-socket connector labeled Spray mount and below nozzle valves 1 through 5...
  • Page 60 Routing the Wire Harness through the Engine Compartment 1. Route the 165 cm (65 inches) branch of the wire harness up and into the rear part of the engine compartment, along the right support for the engine shroud—forward of the duct that connects the air filter and the engine (Figure 136).
  • Page 61 Note: You will complete the installation of the ring terminals in Assembling the Rear Harness and Navigation Electrical Harness to the Battery Cables (page 73). Connecting the Pressure-Sense Tube for the Dash Gauge g033246 Figure 140 Optional Spray Gun Kit No Parts Required 1.
  • Page 62 2. Assemble the receiver mount to the ROPS tube as follows: • If your machine is configured with global navigation satellite system (GNSS) with wide Installing the Navigation area augmentation system (WAAS), assemble the receiver mount to the ROPS tube (Figure 143) with Receiver...
  • Page 63 g030750 Figure 145 Shown with RTK-antenna bracket; machines with GNSS only are similar 1. Navigation receiver 3. Washers (5 mm) g199180 2. Receiver mount 4. Hex-head bolt (5 x 16 mm) Figure 147 1. Coaxial coupler 3. Lock washer 5. Assemble the receiver to the mount (Figure 145) with 2.
  • Page 64 6. Assemble the antenna cable to coaxial connector of the CDMA or GSM cellular modem (Figure 148). 7. Tighten the knurl nuts of the of the antenna cable by hand. Installing the Sprayer Monitor Parts needed for this procedure: Sprayer Monitor—GeoLink precision spray system kit (Model 41623) Display hood Ball mount—GeoLink precision spray system kit...
  • Page 65 Mounting the Sprayer Monitor to 5. Align the hole in the display hood with the stud portion of the threaded standoff (Figure 149). the Dash of the Machine 6. Assemble the hood to the monitor (Figure 149) with 1. Assemble the ball-pivot mount to the dash with the 4 the locknut (5 mm) that you removed in step 1.
  • Page 66 5. Tighten the knob for the monitor arm by hand (Figure 153). Installing the Wire Harnesses for the Navigation Components Parts needed for this procedure: Data Harness (navigation system)—GeoLink precision spray system kit (Model 41623) Electrical Harness (navigation system)—GeoLink precision spray system kit (Model 41623) Cable tie Connecting the Navigation Data and Electrical Harnesses...
  • Page 67 Routing and Connecting the Data Important: Some connectors of the data harness are not used. Ensure that the caps and plugs of the unused Cable to the Navigation Receiver connectors are secure. Connect the 3-socket connector (electrical-power interface) of the navigation-electrical harness to the 3-pin connector (electrical-power interface) of the data harness (Figure 154 Figure...
  • Page 68 g031233 Figure 158 1. 12-pin connector left 5. 390 cm (153-1/2 inches) (gray)—navigation data-harness branch receiver g032991 2. 12-pin connector right 6. 12-socket connector Figure 159 (black)—navigation (gray/black)—data receiver harness 1. Key slots—bottom, 3. Alignment keys—short horizontal wall face (black) 12-socket 3.
  • Page 69 Connecting the Navigation Electrical and Data Harnesses to the Rear Wire Harness of the Machine 1. Route the 100 cm (39-3/8 inches) branch of the electrical harness (Figure 160) with the 1-pin connector, down to the area where the front and rear wire harness for the machine connect;...
  • Page 70 Routing the Navigation Electrical Harness to the Battery 1. Route the 220 cm (86-5/8 inches) branch of the electrical harness for the navigation system across the seat-box angle and down along the left support for the engine shroud (Figure 162). g031297 Figure 163 1.
  • Page 71 electrical harness for the navigation system to the top of the battery (Figure 164). Note: You will complete the installation of the ring terminals in Routing the Navigation Electrical Harness to the Battery (page 70). Routing and Connecting the Data Cable to the Sprayer Monitor g203669 Figure 165...
  • Page 72 g031285 Figure 168 g031284 Figure 167 1. Grommet (dash panel) 3. 26-pin connector (sprayer display) 1. R-clamp 3. Grommet (floor pan) 2. 220 cm (86-5/8 inches) 4. 26-socket 2. 220 cm (86-5/8 inches) 4. Front of the machine data harness branch connector—data harness data harness branch (sprayer monitor)
  • Page 73 Assembling the Rear Harness and Navigation Electrical Harness to the Battery Cables g030943 Figure 170 1. Positive battery cable 8. Battery post (positive) g203667 Figure 169 2. Positive-ring terminal (red 9. Terminal (battery cable) wire)—165 cm (65 inches) 1. 220 cm (86-5/8 inch) 3.
  • Page 74 Note: Do not install the battery cables to the battery at this time. Connecting the Wire Harness for the Optional Pivoting Hose Reel Kit No Parts Required Procedure 1. At the back of the machine, locate the wire harness for the electric hose reel kit at the back of the sprayer tank (Figure 171).
  • Page 75 3. Connect the 2 socket connector of the harness for the 2. Insert the 4-pin connector into the 4-socket connector electric hose reel into the 2 pin connector of the rear (Figure 172). main harness (Figure 171). Note: Press the connectors together until the latch 4.
  • Page 76 g031555 g031556 Figure 174 Figure 175 1. Compression 4. Compression nut—air 1. Compression 3. Compression nut (left fitting—water (right boom (right boom section—blue fitting—water (left boom boom section—blue tube) section—blue tube) tube) section—blue tube) 2. Compression fitting—air 5. Compression nut—water 2.
  • Page 77 • Left boom section down • Right boom section down Connecting the Optional Ultra Sonic Boom Kit No Parts Required Connecting the Wire Harness at the Lift-Cylinder Manifold 1. Connect the 2-pin connector of the sonic boom wire harness to the 2-pin connector of the right cylinder-enable solenoid of the lift-cylinder manifold (Figure 176).
  • Page 78 Pop rivet (Toro Part No. 114439) Support bracket (center section cover—Toro Part No. 131-3703-03) Clip nut (Toro Part No. 94-2413) Flange-head bolt (3/8 x 1-1/4 inches—Toro Part No. 110-5050) Flange locknut (3/8 inch—Toro Part No. 104-8301) Cover strap (Toro Part No. 120-0629) Flange-head bolt (5/16 x 1-1/4 inches—Toro Part No.
  • Page 79 2. Reinforcement plate (double row) 4. Secure the cover extension to the 11-nozzle section g031817 cover (Figure 181) with 11 pop rivets (Toro Part No. 114439). g031824 Figure 181 1. 11-nozzle section cover 3. Pop rivets (Toro Part No. g031826...
  • Page 80 Installing the Support Bracket for g032640 the Center Section Cover 1. Install the 4 clip nuts (Toro Part No. 94-2413) onto the 2 support bracket of the center section cover (Toro Part No. 131-3703-03) as shown in (Figure 183).
  • Page 81 Center Section Cover (11-nozzle) of the Optional Covered-Boom Kit (page 13). 2. Align the rinse-pump cover over saddle plate for the 4. Align the holes in the 2 cover straps (Toro Part No. rinse pump (Figure 187). 120-0629) with the 4 remaining hole in the cover and 4...
  • Page 82 4. Insert the tabs into the slots and release the sides of the cover (Figure 187). Completing the Installation of the GeoLink Spray System Finishing Kit No Parts Required Procedure 1. Move the prop rod for the seats into the slots and tilt the seats down.
  • Page 83 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 84 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.