Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS FOR 10B6201 POST BRACE REPLACEMENT FOR 2B3906 FUSION GOAL
1. These instructions are to be used only if retrofitting an existing goal. For new goal assemblies refer to goal
assembly instructions included with new goal.
2. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify trucking company immediately. Lay out all parts. Remove all cardboard and packaging immediately.
Wet or damp packaging may damage contents.
3. Read through entire instruction before beginning assembly and installation.
Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
3/8" x 7/8" Hex Bolt
3/8" Lock Washer
3/8" Flat Washer
3/8" Square Nut
(Part# TZ247)
(4)
(Part# TZ249)
(4)
(Part# TZ65)
(4)
(Part# TZ60)
(4)
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
Post Brace (2)
(Part# VZ330)
Assembly Tools
9/16" & 3/4"
Wrenches
2016, Rev 2017 Kwik Goal Ltd.
Ratchet with
9/16" & 3/4" Sockets
AND
NZ401 Rev. 07/25/17
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for KwikGoal 10B6201
Summary of Contents for KwikGoal 10B6201
- Page 1 ASSEMBLY INSTRUCTIONS FOR 10B6201 POST BRACE REPLACEMENT FOR 2B3906 FUSION GOAL 1. These instructions are to be used only if retrofitting an existing goal. For new goal assemblies refer to goal assembly instructions included with new goal. 2. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred, notify trucking company immediately.
- Page 2 4. Detach net strap from the eyebolts in the backstays and remove all the net clips from goal as shown. Eyebolt Net Clip Clip Eyebolt Clip Net Clip ***CAUTION*** This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES and shall be secured against overturning.
- Page 3 5. Remove front wheel assemblies as shown. Remove Front Wheel Assemblies 3/8“ X 1” Hex Bolt Left Side Wheel Assembly 3/8“ Lock Washer 3/8“ Flat Washer Left Post Stop Threaded Channel Spacer Left Base ***CAUTION*** This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES and shall be secured against overturning.
- Page 4 6. Remove post braces and discard. Remove remaining hardware holding bases to right and left post corners. With minimum of two people, slide post corners off of bases and lay assembled post and crossbar on ground as shown. Left or Right Post 3/8"...
- Page 5 8. Remove post corners and channel spacers from posts. Insert square nut and channel spacer into posts in order as shown. Reattach post corners to posts. Post 3/8” x 1 3/4” Hex Bolt 3/8” Lock Washer 3/8” Flat Washer Channel Spacer (plastic) 3/8”...
- Page 6 9. With a minimum of two people, lift assembled posts and crossbar and slide post corner back onto bases. Make sure connection of post corners and bases are in place completely and connect with hardware. 3/8" Flat Washer 3/8" Lock Washer Post 3/8"...
- Page 7 11. Attach post brace using square nut in post and using the square nut closest to wheel assembly in base. 3/8” Square Nut 3/8” Flat Washer 3/8” Lock Washer 3/8” X 7/8” Hex Bolt Post Brace 3/8” X 7/8” Hex Bolt 3/8”...
- Page 8 12. Attach anchor plate to front of each base. Attach chain leashes to all four anchor plates. Note: Wheels are not shown in diagrams below for detail clarity. Do not remove wheels. 3/8" x 7/8" Hex Bolt Anchor 3/8" Lock Washer Plate 3/8"...
- Page 9 14. The ground anchor and chain leash system supplied is the recommended and the safest method of anchoring your goal. However, counterbalance weight may be used as a temporary anchoring system. To ensure counterbalance weight remains on the base of your goal you must attach chain leash assembly as shown in figure below.
- Page 10 15. A minimum of 240 lbs. must be placed on the furthest part of the bases for the goal to be stabilized. Make sure that strap or chain of counterbalance weights are secured to each base by the chain leash assembly as shown.
- Page 11 16. After installing, test as described below to verify effectiveness of anchor system. If applicable, allow concrete to fully cure before testing. ANCHOR TEST 1. Clear all persons from a minimum 50 foot radius surrounding the goal. 2. Verify goal is attached to anchors according to instruction. 3.
- Page 12 17. Attach net strap to the eyebolts in the backstays as shown. Pull net strap tight as shown. (NOTE: Do not over tighten net strap. Over tightening may damage goal.) Excess strap can be trimmed to length. Leave 12” to 18”...
- Page 13 CAUTION: GOALS MUST BE PROPERLY ANCHORED OR STORED AT ALL TIMES. Net Clip Net Clip Go to kwikgoal.com for additional product information. ***CAUTION*** This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES and shall be secured against overturning.
Need help?
Do you have a question about the 10B6201 and is the answer not in the manual?
Questions and answers