Table of Contents
Advertisement
Quick Links
HOLDING TANK MONITORS
USER MANUAL
709-BTP7
CANADA
USA
Garnet Instruments Ltd.
Garnet US Inc.
286 Kaska Road
5360 Old Granbury Road
Sherwood Park, AB T8A 4G7
Granbury, TX 76049
SeeLeveL II 709-BTP7 Display Manual (DRAFT)
INTRODUCTION
Through decades of experience and development the SeeLeveL II™
tank monitor series has established itself as the gold standard in level
measurement technology for the recreational vehicle industry.
The SeeLeveL II™ 709-BTP7 builds on previous experience to offer an
exceptional combination of features, accuracy, and reliability, ensuring an
excellent user experience. It provides monitoring of up to 7 tanks, including
2 FRESH, 2 BLACK, and 3 GREY water tank levels. With Bluetooth capability
and the latest SeeLeveL RV 2.0 app, you can view real-time percentage
readouts and receive alerts when tank levels are too high or too low.
The 709-BTP7 monitors battery voltage and includes a pump switch for
added convenience. In addition, the system can display the operating
characteristics of each of the tank sending units, giving it unsurpassed
diagnostic capability.
2024 Garnet Instruments Ltd. All rights reserved. No part of this publication may be
reproduced, Transmitted, transcribed, stored in a retrieval system or translated into any
language in any form by any means without the prior written consent of Garnet Instruments.
Information in this manual is subject to change without notice and does not represent a
commitment on the part of GARNET.
709-BTP7 Display Manual_v1.0 - 07-Jun-2024
Page 1
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Garnet SEELEVEL II 709-BTP7
Summary of Contents for Garnet SEELEVEL II 709-BTP7
-
Page 1: Introduction
Transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of Garnet Instruments. Information in this manual is subject to change without notice and does not represent a commitment on the part of GARNET. -
Page 2: Table Of Contents
Specifications document located on our website. For more detailed information please refer to the chapter entitled TROUBLESHOOTING GUIDE”, section “How to avoid damaging the display or pump switch due to excessive current”. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 2... -
Page 3: About The System
The display can use an existing LPG electrical sender to show the LPG level. It can be automatically calibrated to any sender and shows the level information in percent of full on a 3-digit LED display, from 0% to 100%. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 3... -
Page 4: Model And Serial Number Info
Optional items available to purchase if required. Go to our website for more information: □ Filler Panel to fit previous display hole that is too large. □ Gasket to prevent the display monitor from shorting if mounting to a metal surface. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 4... -
Page 5: Display Installation
A relay may be required for models with a pump or heater switch. help prevent damaging the display. Contact Garnet or go to our website for further details. More installation tips are available in the “Troubleshooting and Installation Tips” section. -
Page 6: Operation Guide
To end the hold mode sooner, press FRESH any tank button and display will shut off. is continuously displayed very dimly to BATT LEVEL IN PERCENT save power until the setting is disabled. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 6... -
Page 7: To Read The Lpg Tank Level
LEVEL IN PERCENT every time a button is pressed. brightness. LEVEL IN PERCENT 1 2 . 0 BATT 4. Press the BATT button to save and exit LEVEL IN PERCENT BATT the programming mode. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 7... -
Page 8: Program The Number Of Senders
Hold Hold hold ALT and the corresponding tank button. 6. To access the setting for the third grey tank (galley), hold ALT and then hold LPG. Hold Hold SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 8... -
Page 9: Program Alarm Set Points For Each Tank
Setting alarm threshold to 0 disables it. Press BATT to save and exit. LEVEL IN PERCENT FRESH NOTE: The example on the right represents a warning alarm that will trigger below 10%. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 9... -
Page 10: Program The Display As Primary Or Secondary
BLACK buttons, and make your selection. On = Secondary mode O F F Off = Primary mode (default) LEVEL IN PERCENT 4. Press the BATT button to save and exit the programming mode. BATT SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 10... -
Page 11: Troubleshooting Guide
LPG will always show “0”. LEVEL IN PERCENT LEVEL IN PERCENT 3. After 5 seconds of showing the signal strength, the display will shut off. LEVEL IN PERCENT NOTE: There are no diagnostics for battery voltage. SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 11... -
Page 12: Wiring Diagnostics
Wiring Diagnostics OPEN CIRCUIT O P n Shows? SINGLE S h t S h t Shows? Shows? S h t Shows? SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 12... - Page 13 SHORT CIRCUIT S h t Shows? S h t Remains? S h t Disappears when a sender is disconnected? S h t S h t Comes back on when sender reconnected? SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 13...
-
Page 14: Troubleshooting & Installation Tips
The next time you take a trip, leave with a high concentration of the surface which can cause low signal strength and unpredictable performance. chemical in the tank and approximately 30% full of fresh water. Drive for 2-3 SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 14... - Page 15 Excessive build-up looks like water to the system as it holds a significant volume of water in the build-up area. Garnet tested solutions: Gorilla Glue Waterproof Patch & Seal Tape (preferred); 3M Professional Grade Rubberized Undercoating, product code 03584;...
-
Page 16: Specifications & Certifications
9.15” high x 2.45” 12.15” high x 2.45” 16" high x 2" wide Sender dimensions (not including wide wide tabs) Operating temperature +32 °F to +140 °F (0 °C to + 60 °C) range SeeLeveL II 709-BTP7 Display Manual (DRAFT) Page 16... -
Page 17: Warranty & Service Information
Alberta, T8A 4G7. Returned warranted items will be repaired or replaced at the discretion of Garnet Instruments. Any Garnet items under the Garnet Warranty Policy that are deemed irreparable by _______________________________________________________________________________ Garnet Instruments will be replaced at no charge or a credit will be issued for that item subject to the customer’s request. _______________________________________________________________________________...
Need help?
Do you have a question about the SEELEVEL II 709-BTP7 and is the answer not in the manual?
Questions and answers