SINTERIT LISA X Short User Manual
Sls 3d printer
Hide thumbs
Also See for LISA X:
- Original user manual (87 pages) ,
- Translation of the original user manual (62 pages) ,
- Manual (11 pages)
Related Manuals for SINTERIT LISA X
Summary of Contents for SINTERIT LISA X
- Page 1 Sinterit SLS 3D PRINTER REV. E Short user manual Please read the manual before using the product. For the most up-to-date manual, visit our website: www.sinterit.com/support/...
-
Page 2: Table Of Contents
2.5 Preparing the print chamber ............................. 8 2.6 Final steps before printing ..............................8 3. Removing and cleaning the printout ...........................9 4. Cleaning the printer ..............................10 4.1 Cleaning the print chamber.............................10 4.2 Cleaning the Overflow bin ...............................11 Sinterit LISA X Short User Manual | 2... -
Page 3: General Information
• headquarters address: Sinterit sp. z o.o., ul. Nad Drwina 10-B3, 30-741 Krakow, Poland For a list of distributors and technical support in each country, please visit our website www.sinterit.com IMPORTANT! To facilitate the assistance process, please have the information ready: •... - Page 4 It is necessary to wear antistatic clothes and shoes. Mandatory action when working with powder. IMPORTANT! Information essential to correctly perform a specific task. IMPORTANT! You must read the instructions before taking action. Sinterit LISA X Short User Manual | 4...
-
Page 5: Printer Overview
GAS INLET NIPPLE (QUICK CONNECT FITTING) INERT GAS CONTROL SYSTEM POWER SOCKET POWER SWITCH (ON/OFF) Fig. 1.3 View of the left side of the printer. Fig. 1.4 View of the back of the printer. Sinterit LISA X Short User Manual | 5... -
Page 6: Preparing To Print
2. PREPARING TO PRINT 2.1 General information WARNING! • The Sinterit set of devices, including the Lisa X 3D Printer, is not intended for use in an explosive atmosphere. • The possibility of an explosive atmosphere is anticipated inside the device. -
Page 7: Choosing The File
2.3 Choosing the file IMPORTANT! In order to print, you will need a file prepared in Sinterit Studio, which you can download from our website www.sinterit.com/software. IMPORTANT! • If any part of the printer requires maintenance or replacement, a corresponding message will appear on the screen. -
Page 8: Preparing The Print Chamber
If the inert gas control system is incorrectly connected, a proper message will appear. 2.6 Final steps before printing ATTENTION! If anything during the printer operation concerns you, press the E-STOP button and contact our After-sales team: support@sinterit.com. Sinterit LISA X Short User Manual | 8... -
Page 9: Removing And Cleaning The Printout
10. Carry the IO BOX and its contents onto the foldable tray or to the Multi PHS worktop (fig. 3.4). 11. Press DONE on the screen. 12. Clean the printout of unsintered powder. You may use the accessories provided in Dedicated Powder Tools. Sinterit LISA X Short User Manual | 9... -
Page 10: Cleaning The Printer
Make sure no tools remain in the print chamber. Press POSITION BEDS to begin the positioning process of the Beds. For cleaning the printer Sinterit recommends dedicated solutions: the Multi PHS or ATEX/Intertek Vacuum Cleaner with Separator. Whether you are using the Multi PHS or an ATEX/Intertek... -
Page 11: Cleaning The Overflow Bin
If you want to know how much fresh powder you need to add to the used powder press SHOW REFRESH INFO. If you wish to instead do that another time, press SKIP. Sinterit LISA X Short User Manual | 11... - Page 12 SINTERIT Sp. z o.o. ul. Nad Drwina 10/B-3, 30-741 Krakow, Poland www.sinterit.com...
Need help?
Do you have a question about the LISA X and is the answer not in the manual?
Questions and answers