Advertisement
Quick Links
Operating instructions
LIFAN Petrol Water Pump
64767
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Advertisement
Related Manuals for WilTec 64767
Summary of Contents for WilTec 64767
- Page 1 Operating instructions LIFAN Petrol Water Pump 64767 Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further...
- Page 2 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man- ual, nor in the diagrams and illustrations shown.
- Page 3 Do not leave the motor run in a closed room or a badly ventilated place. The exhaust fumes of the motor contain toxic carbon monoxide (CO) that provoke unconsciousness or even death. Danger of suffocation! © by WilTec Wildanger Technik GmbH Item 64767 Page 3 http://www.WilTec.de...
- Page 4 Parts © by WilTec Wildanger Technik GmbH Item 64767 Page 4 http://www.WilTec.de http://www.aoyue.eu 11 2023-1 http://www.teichtip.de...
- Page 5 The length of the hose should not exceed the length absolutely required. The lower the distance to the water surface is, the bigger is the suction effect. © by WilTec Wildanger Technik GmbH Item 64767 Page 5 http://www.WilTec.de...
- Page 6 5. Slide a hose clamp (29) onto the other end of the suction hose (B). 6. Put the suction basket (33) into the suction hose and fix using a hose clamp (29). © by WilTec Wildanger Technik GmbH Item 64767 Page 6 http://www.WilTec.de http://www.aoyue.eu 11 2023-1...
- Page 7 Upper oil level Drain screw Lower oil level Attention! Operating the device with too low a motor oil level can cause serious damages to the motor! © by WilTec Wildanger Technik GmbH Item 64767 Page 7 http://www.WilTec.de http://www.aoyue.eu 11 2023-1...
- Page 8 Do not let the motor run without installed air filter; otherwise, dirt and other contamina- tions can penetrate the motor through the carburettor, provoking an early wear of the motor. © by WilTec Wildanger Technik GmbH Item 64767 Page 8 http://www.WilTec.de...
- Page 9 In case the pump is empty and has run hot, stop the motor, wait until it has cooled down, then fill in new water. № Name Letter Name Plug Water opening © by WilTec Wildanger Technik GmbH Item 64767 Page 9 http://www.WilTec.de http://www.aoyue.eu 11 2023-1 http://www.teichtip.de...
- Page 10 2. Switch the fuel cock to the “ON” position. 3. For starting a cold motor, set the throttle to the “CLOSED” position. For starting a warm motor, the throttle should be set to the “OPEN” position. © by WilTec Wildanger Technik GmbH Item 64767 Page 10 http://www.WilTec.de...
- Page 11 (C) to the left. • Reduce the amount of water to be pumped: slide the gas lever (C) to the right. © by WilTec Wildanger Technik GmbH Item 64767 Page 11 http://www.WilTec.de http://www.aoyue.eu 11 2023-1...
- Page 12 Switch off the motor before any maintenance! If you absolutely need to perform mainte- nance on a running motor, only work in a well-ventilated room. Exhaust fumes contain carbon monoxide (CO; this is a toxic gas that may cause unconsciousness or even death. © by WilTec Wildanger Technik GmbH Item 64767 Page 12 http://www.WilTec.de...
- Page 13 5. Add a few drops of engine oil onto the air filter (21) and squeeze it to spread the oil. 6. Re-plug the parts (19–24) to the filter hub (A). 7. Re-screw the wing nut (25) by hand. © by WilTec Wildanger Technik GmbH Item 64767 Page 13 http://www.WilTec.de http://www.aoyue.eu...
- Page 14 3. Take out the filter inset (27). 4. Clean the filter inset (27) using spirit/etha- nol and let it dry. 5. Re-place the filter inset (27). 6. Re-close the tank lid (26). © by WilTec Wildanger Technik GmbH Item 64767 Page 14 http://www.WilTec.de http://www.aoyue.eu 11 2023-1 http://www.teichtip.de...
- Page 15 (target state: marking of max. oil level of the lower edge of the filler, see fig.). 3. Top up with oil if required. 4. Re-screw the plug (6) in. © by WilTec Wildanger Technik GmbH Item 64767 Page 15 http://www.WilTec.de http://www.aoyue.eu 11 2023-1 http://www.teichtip.de...
- Page 16 Turn the motor several times for the oil to disperse evenly, then screw the spark plug in again. 5. Cover the water pump to protect it against dust. © by WilTec Wildanger Technik GmbH Item 64767 Page 16 http://www.WilTec.de...
-
Page 17: Troubleshooting
Max. height of use (m) 1000 WATER PUMP (SELF PRIMING) Max. flow rate ( m³ ⁄ Max. suction depth (m) Max. lifting height (m) Diameter of pressure-suction connection (㎜) © by WilTec Wildanger Technik GmbH Item 64767 Page 17 http://www.WilTec.de http://www.aoyue.eu 11 2023-1 http://www.teichtip.de... - Page 18 Stop method Main switch Important note: Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 64767 Page 18 http://www.WilTec.de http://www.aoyue.eu 11 2023-1...
Need help?
Do you have a question about the 64767 and is the answer not in the manual?
Questions and answers