Riello Hi, Comfort T200 Instruction Manual
  1. Manuals
  2. Brands
  3. Riello Manuals
  4. Thermostat
  5. T200
  6. Instruction manual

Riello Hi, Comfort T200 Instruction Manual

Hide thumbs Also See for Hi, Comfort T200:
Table of Contents

Advertisement

Quick Links

Download this manual
T200
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hi, Comfort T200 and is the answer not in the manual?

Questions and answers

Related Manuals for Riello Hi, Comfort T200

Summary of Contents for Riello Hi, Comfort T200

  • Page 1 T200 INSTRUCTION MANUAL...

  • Page 2: Table Of Contents

    MODIFY AMBIENT SETPOINT TEMPORARY MANUAL MODE ENERGY-SAVING MODE FAULT DISPLAY Scan the QR code to download the complete version of the Hi, Comfort T200 manual in english and in the other available languages or enter www.hi-comfort.com CONFIGURATION MENU 16.1 Radio signal level The following symbols are used in some parts of the booklet: WARNING = for actions requiring special care and adequate preparation.

  • Page 3: General Safety Warnings

    2. Receiving the product measures in mm 4. Description The Hi, Comfort T200 thermostat, in RF combination with the Hi, Comfort T300, allows optimal comfort control within every room of the house. Equipped with an inno- vative design and touch button technology for menu navigation.

  • Page 4: Installation

    5. INSTALLATION 5.3 Place of installation 5.1 Inserting the batteries Use a screwdriver (1) to separate the dis- play from the plastic casing as shown in the figure below. 5.4 T200 electrical connection 5.2 Wall mounting Relay maximum load Relay normally open, 250VAC 5A cosФ = 1.

  • Page 5: Configurations With T200 In The Presence Of A Boiler Or Hybrid System

    7. CONFIGURATIONS WITH T200 IN THE PRESENCE OF A BOILER OR HYBRID SYSTEM MAIN ZONE MANAGED BY A BO- MAIN ZONE + ZONE 1 e 2 MANA- ZONE VALVES SYSTEM LER + ZONE 1 AND 2 MANAGED GED BY BE16 Main zone, Zone 1...7: BY A BE16 Main zone, Zone 1 e 2:...

  • Page 6: Configurations With T200 In The Presence Of A System Full Electric

    8. CONFIGURATIONS WITH T200 IN THE PRESENCE OF A SYSTEM FULL ELECTRIC MAIN ZONE MANAGED BY A PDC + MAIN ZONE + ZONE 1 e 2 MANA- ZONE VALVES SYSTEM ZONE 1 AND 2 MANAGED BY A BE16 GED BY BE16 Main zone, Zone 1...7: Main zone: Main zone, Zone 1 e 2:...

  • Page 7: T200 Display

    6. T200 DISPLAY The T200 device consists of: ● symbol-based LCD display, 6 alphanu- meric digits, white on black background ● pairing/unpairing/reset button accessible only with an adeguated tool through the casing. ● 4 touch buttons: Confirm Back Up/Down...
  • Page 8 Symbol key The meaning of the symbols is described below. RF Antenna - symbol is lit if the T200 is paired and connected to the T300 - symbol blinks if the device is not paired with any T300 - symbol is off if the device is paired but communication is not active. Battery The symbol activates when the battery voltage drops below 2.2Vdc. From the time the symbol activates (blinking), approximately one month of operation is...

  • Page 9: Ignition

    9. Ignition Otherwise, if the T200 is paired with a T300, but communication is not yet present (wait- When the batteries are inserted, the symbol ing for first message or loss of connection), test appears and all symbols light up. the symbol “ ” is off. Once the symbol test is complete, the firmware version of the T200 appears on To pair the T200 device with a system, the the display for a few seconds.

  • Page 10: Leaving (Un-Pairing)

    Component characteristics If the symbol “ ” is off, this indicates that the procedure has failed and un-pairing RF module 868 MHz must therefore be repeated. 300 m in free field in RF distance 10.3 Deleting radio connection data communication with T300 (return to factory settings) Press the key inside the lower casing for at least 5 seconds to reset the data and return...

  • Page 11: Modify Ambient Setpoint

    AUTOMATIC ..13. TEMPORARY MANUAL mode When the T200 is set to automatic mode, the TEMPORARY MANUAL mode can be activated. This mode consists of a tempo- rary setpoint change of the current time band. At the end of the time band, the zone returns to AUTOMATIC mode.

  • Page 12: Configuration Menu

    After 5 seconds, the display returns to nor- mal operation. To access the offset modify screen, hold down key in the main screen until the blink- If the fault refers to the hybrid or full elec- ing °C symbol appears, then press the trical system, the fault code is preceded by key again.
  • Page 13 ✎...
  • Page 14 ✎...
  • Page 16 RIELLO S.p.A. Via Ing. Pilade Riello, 7 37045 - Legnago (VR) www.riello.it In order to improve its products, our company reserves the right to modify the characteristics and information contained in this manual at any time and without prior notice. Consumers statutory rights are not aected.

Table of Contents