Omron VARISPEED V7 User Manual page 15

Simple Data Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
6 Programming Features - - - - - - - - - - - - - - - - - - 52
Hardware - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 52
Software (Constant) - - - - - - - - - - - - - - - - - - - - - - - - - - - 52
Constant Setup and Initialization - - - - - - - - - - - - - - - - - - - - - - 53
Constant Selection/Initialization (n001) - - - - - - - - - - - - - 53
Using V/f Control Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 55
Adjusting Torque According to Application - - - - - - - - - - - 55
Using Vector Control Mode - - - - - - - - - - - - - - - - - - - - - - - - - - 59
Precautions for Voltage Vector Control Application - - - - - 59
Motor Constant Calculation- - - - - - - - - - - - - - - - - - - - - - 60
V/f Pattern during Vector Control - - - - - - - - - - - - - - - - - - 61
Switching LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - - - - 62
How to Select LOCAL/REMOTE Mode - - - - - - - - - - - - - 63
Selecting Run/Stop Commands- - - - - - - - - - - - - - - - - - - - - - - 63
LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 63
REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 64
Operating (Run/Stop Commands) by Communications - - 64
Selecting Frequency Reference - - - - - - - - - - - - - - - - - - - - - - 64
LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 65
REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 65
Setting Operation Conditions - - - - - - - - - - - - - - - - - - - - - - - - 66
Autotuning Selection (n139) - - - - - - - - - - - - - - - - - - - - - 66
Reverse Run Prohibit (n006)- - - - - - - - - - - - - - - - - - - - - 74
Multi-step Speed Selection - - - - - - - - - - - - - - - - - - - - - - 74
Operating at Low Speed - - - - - - - - - - - - - - - - - - - - - - - - 75
Adjusting Speed Setting Signal - - - - - - - - - - - - - - - - - - - 76
Adjusting Frequency Upper and Lower Limits- - - - - - - - - 77
Using Four Acceleration/Deceleration Times - - - - - - - - - 77
Momentary Power Loss Ridethrough Method (n081)- - - - 79
S-curve Selection (n023) - - - - - - - - - - - - - - - - - - - - - - - 80
Torque Detection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 81
Frequency Detection Level (n095)- - - - - - - - - - - - - - - - - 82
Jump Frequencies (n083 to n086) - - - - - - - - - - - - - - - - - 84
Continuing Operation Using Automatic Retry Attempts - - 84
Frequency Offset Selection (n146) - - - - - - - - - - - - - - - - 85
14