Subscribe to Our Youtube Channel
Related Manuals for Salamander Pumps TNK-350-C5
Summary of Contents for Salamander Pumps TNK-350-C5
- Page 1 Installation and warranty guide for TankBoost range This document should be given to the end user and retained for future reference. Should you need to contact Salamander Pumps you will need the below information.
-
Page 2: Table Of Contents
Warranty Correct installation is the guarantee of safety Thank you for choosing and a trouble free system. It is therefore Salamander Pumps Terms and Conditions important to read these instructions thoroughly and ensure you comply with them. Incorrect fitting could cause serious injury, death, property damage and invalidate the warranty. -
Page 3: Product Description
Performance curve, applicable to all TankBoost pumped models. 562 (CAT 5) Flow (lpm) Product Diagram Additional Storage Units TNK-100/ TNK-200/ TNK-350/ TNK-450/ Pump Control TNK-100-C5 TNK-200-C5 TNK-350-C5 TNK-450-C5 Outlet Unit Overflow Mains water inlet Ball valve Connection connection Rating Tank Label Overflow... -
Page 4: Installation Notes
Installation Notes Typical Installation Diagrams Outlet from TankBoost - Location Boosted water to outlets Outlet from TankBoost - and hot water system Boosted water to outlets - The floor/mounting surface (supporting - Ensure that the stored volume of water and hot water system Inlet to TankBoost) must be flat and level, fully remains above 4°C and below 20°C to avoid... -
Page 5: Electrical Installation
Electrical Installation Maintenance • - TankBoost must be connected to the - If the supply cord is damaged, it must be Pressure Vessel Pre-Charge If below 1.5 bar, increase the pressure electrical supply using the mains cable, replaced by the manufacturer, its service - To maintain optimum performance of by injecting air into the vessel via the wired to a UK 3-pin plug or fused spur (with... -
Page 6: Technical Specification
Empty Weight (kg) 22.2 32.9 45.7 51.1 off when all Pressure sensor Weights outlets closed Contact Salamander Pumps. Filled Weight (kg) 122.2 232.9 395.7 501.1 calibration Inlet Connection 1/2" BSP Male Connections Linking Connection Via Linking Kit Supplied Water Temperature 4°C - 20°C... -
Page 7: Control Unit Display Codes
Control Unit Display Codes Factory Reset (Control Unit) In normal operation the control unit displays pressure or Your unit is pre-set with its operating parameters during assembly and testing. current readings directly from the pump in the tank unit. START An LED will be lit up to show whether the pressure is If your unit is failing to operate and if instructed to do so by the Salamander Tech Desk team, PRESS. -
Page 8: Additional Water Storage Tanks
Additional Water Storage Tanks WEEE Directive Your appliance contains valuable materials WEEE Directive 2012/19/EU which could be recovered or recycled. At - Additional storage tanks must be the same size as the main pumped unit. At the end of the product life dispose the end of the product’s useful life please of packaging and product in a - All tanks must be located on the same level and as close together as possible so as... -
Page 9: Warranty
Warranty Terms and conditions 1. The Scope of the Warranty 2. The Warranty Periods This Warranty shall only be enforceable by you if the following terms and conditions have SALAMANDER PUMPED SHOWER SYSTEMS The Warranty periods referred to in paragraph been complied with: LTD (“the company”) Warrants subject to the 1 above are as follows:... - Page 11 Get in touch, we’re here to help call us on 0191 516 2002 Unit 2c Colima Avenue Enterprise Park West Sunderland, SR5 3XE For ROI/EU Customers: MT Agencies Ireland Ltd Fearn House, Jamestown Business Park Jamestown Road, Finglas Dublin 11, D11 K7TV Register your warranty Online at: www.salamanderpumps.co.uk By phone: 0191 516 2002...
Need help?
Do you have a question about the TNK-350-C5 and is the answer not in the manual?
Questions and answers