Table of Contents
Advertisement
Quick Links
Operator's Instruction Manual
14" COMPACT DOWNCUT
CONCRETE AND ASPHALT SAW
READ AND UNDERSTAND THE OPERATOR'S SAFETY MANUAL
THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
Death or serious injury could occur if this machine is used improperly.
READ AND UNDERSTAND THE ENGINE MANUFACTURERS INSTRUCTIONS AND OPERATORS MANUAL BEFORE OPERATION.
EQUIPMENT DEVELOPMENT COMPANY, INC.
1-800-638-3326
1-800-638-3326
Phone: 800-638-3326 or 301-663-1600 • Fax: 800-447-3326 or 301-663-1607
KL-14
100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
• edcoinc.com • techsupport@edcoinc.com
Website: www.edcoinc.com • E-mail: techsupport@edcoinc.com
E-KL14-I-0124
Printed in USA
©2024
JWA
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Edco KL-14-7H
Summary of Contents for Edco KL-14-7H
- Page 1 E-KL14-I-0124 Operator’s Instruction Manual KL-14 14” COMPACT DOWNCUT CONCRETE AND ASPHALT SAW READ AND UNDERSTAND THE OPERATOR’S SAFETY MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. READ AND UNDERSTAND THE ENGINE MANUFACTURERS INSTRUCTIONS AND OPERATORS MANUAL BEFORE OPERATION. EQUIPMENT DEVELOPMENT COMPANY, INC.
-
Page 2: Safety Information
SAFETY INFORMATION E-KL14-I-0124 SAFETY MESSAGES ELECTRICAL POWERED EQUIPMENT CONTINUED • Safety Instructions are proceeded by a graphic alert symbol of DANGER, • Do not disconnect power by pulling cord. To disconnect, grasp the WARNING, or CAUTION. plug, not the cord. •... -
Page 3: Table Of Contents
E-KL14-I-0124 OPERATOR’S INSTRUCTION MANUAL Model KL-14 Compact Saw TABLE OF CONTENTS Section Page Number Safety Information ........2 Machine Safety Symbol Label Reference . -
Page 4: Machine Safety Symbol Label Reference
E-KL14-I-0124 MACHINE SAFETY SYMBOL LABEL REFERENCE This symbol means that the guards must remain in place while the engine/motor on the machine is running because death or personal injury may result. (Yellow background with black pictogram and black outline) This symbol means that there are moving parts and if feet/fingers/digits are inserted under any edge of the cutter/grinder/saw cover while the engine/motor on the machine is running that personal injury and loss of foot/fingers/digits may result. - Page 5 E-KL14-I-0124 MACHINE SAFETY SYMBOL LABEL REFERENCE This symbol means that the Operator’s, owners, instruction and/or manufacturer(s) manuals must be read and understood before operating or attempting to operate this electrical, gasoline, diesel or propane powered equipment, failure to do so can result in personal injury and possible death. (Blue background with white pictogram.) This symbol means that proper eye protection must be worn/used during the operation of this equipment.
-
Page 6: California Proposition 65 Warning
California. While the exposure from EDCO products may be negligible or well within the “no significant risk” range, out of an abundance of caution, EDCO has elected to provide these Proposition 65 warnings. -
Page 7: Dust And Crystalline Silica Warning
E-KL14-I-0124 DUST AND CRYSTALLINE SILICA WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheets and/or consult your employer, the manufacturers/suppliers, governmental agencies such as OSHA and NIOSH and other sources... -
Page 8: Safety Guidelines
E-KL14-I-0124 Safety Guidelines Read and understand all operating instructions before operating this equipment. Death or serious injury can result if this machine is used improperly. Safety warnings and guidelines do not by themselves eliminate danger. They are not given as substitutes for proper accident prevention procedures and good judgement. -
Page 9: Operating Controls
E-KL14-I-0124 Operating Controls MODEL KL-14 EQUIPMENT DEVELOPMENT CO., INC. Collapsable Handle Handle Lock Choke Water Valve Rope Pull Guide Bar Depth Control On/Off Switch Throttle Please Note: Controls shown are for the model indicated. The location of these controls may vary on the different models. Due to improvements and changes in the equipment, the illustration shown may be different from the actual machine. -
Page 10: Operating Instructions
E-KL14-I-0124 Operating Instructions IMPORTANT NOTES • Read and understand all operating instructions before operating this equipment. Death or serious injury can result if this machine is used improperly. • Concrete saws are designed to be used to cut flat horizontal concrete or asphalt slabs using diamond saw blades. - Page 11 E-KL14-I-0124 Operating Instructions • FOR WET CUTTING: Attach the water supply. A flow rate of approximately 2 gallons per minute EQUIPMENT DEVELOPMENT CO., INC. EQUIPMENT DEVELOPMENT CO., INC. (minimum) is required. Attach the water hose to the coolant valve. Use the valve to control the flow of water.
-
Page 12: Changing Blades
(Figure 6). • Be sure the arbor shaft, backing plate, and blade cap are clean and in good condition. Make sure the threads are clean and undamaged. If any damage is detected, consult your EDCO dealer (or the EDCO factory). •... - Page 13 Do not use warped, twisted, or out-of-balance blades. Unbalanced blades will wear excessively, vibrate and damage both arbor shaft and bearings. Do not use a blade without a drive pinhole (Figure 7) . For safety reasons, EDCO does not recommend the use of any abrasive blades. Abrasive blades can •...
-
Page 14: Maintenance
E-KL14-I-0124 Maintenance Grease Bearings Every 4 Hours of Use NOTE: Wipe grease fittings clean before servicing. Grease Fittings 1-800-638-3326 1-800-638-3326 • edcoinc.com • techsupport@edcoinc.com Page 14... - Page 15 E-KL14-I-0124 Maintenance Schedule Repairs are to be Read and follow instructions done by authorized in the Engine Manufacturer’s EDCO DEALERS only. Manual Follow Engine Manufacturer’s Maintenance Schedule Visual Inspection of Entire Machine Check Engine Oil Change Engine Oil* (Refer to Engine manual)
- Page 16 E-KL14-I-0124 THIS PAGE LEFT BLANK INTENTIONALLY 1-800-638-3326 1-800-638-3326 • edcoinc.com • techsupport@edcoinc.com Page 16...
-
Page 17: Limited Equipment Warranty Of Sale
*Seller reserves the right to alter payment terms. EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been 3. -
Page 18: Stop - Before Using This Product
EDCO product group. The information in these tracks help businesses be successful with those products. EDCO is always updating online training / information so you always have the most recent content. Also see Operator’s Safety & Limited Warranty Manual Equipment Development Co., Inc.
Need help?
Do you have a question about the KL-14-7H and is the answer not in the manual?
Questions and answers