Related Manuals for SystemAir SAVE VSR 400
Summary of Contents for SystemAir SAVE VSR 400
- Page 1 SAVE VSR 400 Installation instructions Document in original language | 456008 · v01...
- Page 2 This also applies to products already ordered, as long as it does not affect the previously agreed specifications. Systemair is not liable or bound by warranty if these instructions are not adhered to during installation or service. 456008 | v01...
-
Page 3: Table Of Contents
Contents Overview ............1 General Description ........1 Warranty ..........1 Type label..........1 Important Safety Information ......1 Intended Use.........1 Admonitions .........2 Technical Data ..........2 Dimensions and Weight ......2 Duct connections........3 Installation recommendation regarding condensation ........3 3.3.1 Condensation inside of the unit .........3 3.3.2 Condensation outside of the unit .........4 Delivery, Transport, Storage.......4... -
Page 5: Overview
For the assertion of warranty claims, the products must be correctly connected and operated, and used in accordance with the data sheets. Further prerequisites are a completed maintenance plan with no gaps and a commissioning re- port. Systemair will require these in the case of a warranty claim. Type label Before calling your service representative, make a note of the specification and production number from the type label, which can be found next to the external connections and inside of the unit. -
Page 6: Admonitions
| Technical Data • The system should operate continuously, and only be stopped for maintenance/service. • Do not connect tumble dryers to the ventilation system. • Make sure that filters are mounted before starting the unit. Admonitions Danger • Make sure that the mains supply to the unit is disconnected before performing any maintenance or electrical work! •... -
Page 7: Duct Connections
Technical Data | Duct connections Fig. 2 Duct connections Description Description Symbol Symbol Supply air Outdoor air Exhaust air Extract air Installation recommendation regarding condensation 3.3.1 Condensation inside of the unit The unit should run continuously. If the unit is intended to be stopped by the user manually or due to calendar function we recommend to install air tight dampers at extract and supply air ducts. -
Page 8: Condensation Outside Of The Unit
Transport and storage The SAVE VSR 400 should be stored and transported in such a way that it is protected against physical damage. It should be covered so dust, rain and snow cannot enter and damage the unit and its components. -
Page 9: Location And Space Requirements
Location and Space Requirements The SAVE VSR 400 should preferably be installed in a separate room (e.g. storeroom, laundry room or similar.). 456008 | v01... -
Page 10: Outdoor Air Intake Location Recommendation
Access to Power supply The SAVE VSR 400 is supplied with approximately 1 – 1,5 m cable and plug for 230V, single phase earthed connection. Make sure a power outlet is reachable by the plug. -
Page 11: Installation And Configuration Of Accessories
Please follow instructions included with the accessory or consult “Service and Accessories Installation” manual which can be found in our online catalogue. Electrical connections Main circuit board layout The SAVE VSR 400 is equipped with built-in regulation and internal wiring. Fig. 4 Main circuit board connections Position Description... -
Page 12: External Connections (Connection Board)
| Electrical connections Position Description Analog input 1 — Outdoor air sensor Analog input 2 — Supply air sensor Analog input 3 — Freely configurable Analog input 4 — Freely configurable / Overheat temperature sensor (units with heater) Analog input 5 — Freely configurable Digital input 1 —... -
Page 13: Before Starting The System
Before Starting the System | Position Description UI1–5 Freely configurable universal input. Can be set as analog input (0–10 V) or a digital input (24 V). UI1 default configuration: Pressure guard UI2 default configuration: Cooker hood UI3 default configuration: Fire alarm UI4 default configuration: Refresh Maximum current 200mA at 24VDC +-10%. -
Page 14: Concluding Routines
| Concluding Routines Set speed of supply and extract air fans for each level. When finished, review your settings. It is possible to go back to previous menus and make modifications. Choose heating type or none. Reset filter changer timer if necessary. Finish startup wizard with OK button. -
Page 15: Eu Declaration Of Conformity
Degrees of protection provided by enclosures (IP Code). The manufacturer hereby confirms that EN 62233 SAVE VSR 400 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard comply with all applicable requirements in the following to human exposure. - Page 16 Systemair UAB Linų st. 101 LT–20174 Ukmergė, LITHUANIA Phone +370 340 60165 Fax +370 340 60166 www.systemair.com...