Summary of Contents for Helios ecgreen KWL EC 60 Pro
Page 1
Helios Ventilatoren MONTAGE- UND BETRIEBSVORSCHRIFT INSTALLATION AND OPERATING INSTRUCTIONS NOTICE DE MONTAGE ET D’UTILISATION Wand-Einbaugerät Wall installed unit Groupe double-flux mural KWL EC 60 Pro KWL EC 60 Pro FF Wärmerückgewinnung und EC-Technik für Einzelräume Heat recovery and EC-motor technology for single rooms Ventilation décentralisée avec récupération...
Wenn die nachfolgenden Ausführungen nicht beachtet werden, entfällt unsere Gewährleistung. Gleiches gilt für Haf- tungsansprüche an den Hersteller. Der Gebrauch von Zubehörteilen, die nicht von Helios empfohlen oder angeboten werden, ist nicht statthaft. Even tuell auftretende Schäden unterliegen nicht der Gewährleistung.
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Wir empfehlen vor der Beschaffung eines Unterdruck-Überwachungssystem für Feuerstätten mit dem zuständigen Schornsteinfeger zu sprechen, um eventuelle Wünsche zu berücksichtigen. 111 Elektrischer Anschluss Lebensgefahr durch elektrischen Schlag! GEFAHR Vor allen Wartungs- und Installationsarbeiten oder vor Öffnen des Schaltraumes ist das Gerät allpolig vom Netz zu trennen! Der elektrische Anschluss darf nur von einer autorisierten Elektrofachkraft entsprechend den nachstehenden Anschlussplänen ausgeführt werden Der Elektroanschluss muss bis zur Endmontage allpolig...
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF KAPITEL 3 Wandmontage KWL 60 RS Rohbauset MONTAGE/AUFSTELLUNG Kernbohrung in der Wand vornehmen (siehe Abb. 5). Anschl. Wandhülse in die Wand einschieben und einputzen. Um beim Einputzen eine Verformung der Wandhülse zu vermeiden, muss das Versteifungskreuz aus Styro- ACHTUNG por (siehe Abb 1) eingeschoben sein Nach dem Verputzen, ist dieses wieder zu entfernen! Abb 5...
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Montage KWL 60 WV Wandhülsen-Verlängerung Abb 9 max. 560 mm Wanddicke bei zwei Verlängerungshülsen Wandring auf Wandhülse aufstecken max. 2 Wandhülsen- Verlängerungen Wand Verlängerung Kondensatablauf Kondensatablauf mit 20 mm Überstand aufstecken zur Wand ablängen max.
Page 7
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Hierzu im Untermenü C4.1 (Standard Wochenprogramm) das gewünschte WP auswählen und bestätigen. Wenn ein individuelles Wochenprogramm erstellt werden soll, kann dies im Untermenü 4.2 (Individuelles Wochenprogramm) für jeden Wochentag festgelegt werden. C5 = Urlaubsprogramm: Über das Menü...
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF E11 = Software Version: Abfrage zum Software-Versionsstand der Hauptplatine und des Bedienelements. E12 = Rücksetzen auf Werkseinstellungen: Alle Parameter können auf die Werkseinstellung zurückgesetzt werden. Wenn die Einstellungen des Wochenprogramm nicht resetet werden sollen, ist dies vorab optional einstellbar.
Page 9
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF MENÜ Bedienmenü Erstinbetriebnahme (A1) - Adresse 1-2-3-4 - Spracheinstellungen - Datum / Uhr ............. . . NOTIZEN: .
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Fehlermenü/Fehleranzeige im Display Fehlermenü/Fehleranzeige im Display Bei einem Fehler wird die Fehlermeldung angezeigt, Leuchtdauer siehe Displaybeleuchtung. Ist das Display aus, blinkt der Drehencoder rot! Bei einem Fehler wird die Fehlermeldung angezeigt, Leuchtdauer siehe Displaybeleuchtung.
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF KAPITEL 5 Elektrischer Anschluss ELEKTROANSCHLUSS Lebensgefahr durch elektrischen Schlag! GEFAHR Vor allen Wartungs- und Installationsarbeiten oder vor Öffnen des Schaltraumes ist das Gerät allpolig vom Netz zu trennen! Der elektrische Anschluss darf nur von einer autorisierten Elektrofachkraft entsprechend dem nachstehenden Anschlussplan ausgeführt werden Die einschlägigen Normen, Sicherheitsbestimmungen (z.B.
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF KAPITEL 6 Kondensatableitung REINIGUNG UND Während der Heizperiode kondensiert die Feuchtigkeit der Abluft zu Wasser. Beim Baden, beim Saunieren sowie beim WARTUNG Wäschetrocknen oder bei Neubauten, kann sich reichlich Kondenswasser bilden. Das Kondenswasser muss frei aus dem Gerät ablaufen können.
Page 19
Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF...
Page 20
ENGLISH TABLE OF CONTENTS GENERAL INSTALLATION AND OPERATING INSTRUCTIONS PAGE 1 CHAPTER 1 Important Informationen ..................................Page 1 Warning and safety instructions ................................Page 1 Warranty – Exclusion of liability ................................Page 1 Certificates ......................................Page 1 Receipt ....................................... Page 1 Storage .......................................
If the preceding instructions are not observed all warranty claims and accommodation treatment are excluded. This also applies to any liability claims extended to the manufacturer. The use of accessories not offered or recommended by Helios is not permitted. Potential damages are not liable for warranty.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF 111 Electrical connection All work must be carried out with the equipment fully isolated from the power supply The electrical connection DANGER are to be carried out in accordance with the relevant wiring diagram and are only to be done by a certified electrician The electrical connection must be fully isolated from the supply up to the final assembly! All relevant safety regulation, national standards and norms are to be adhered to.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF CHAPTER 3 Wall installation of KWL 60 RS first fix set INSTALLATION Drill a core hole in the external wall (see Fig. 3). Then insert wall sleeve into the wall and plaster it in. ATTENTION In order to avoid a deformation of the wall sleeve, the polystyrene cross support (Fig 1) must be inserted This has to be removed again after the plastering!
Trennsteg auf das Gehäuse from stainless steel der Lüftungseinheit aufstecken to the extension sleeve not provided by Helios) ~ 104 CHAPTER 4 Functional description to menu tree of comfort controller KWL-BC COMFORT CONT- ROLLER A1 = Initial start-up:...
Page 25
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF C4 = Clock timer: It is possible to select between 6 already preset weekly programs: WP 1, WP 2, WP 3, WP 4, WP 5, WP OFF. Select and confirm the desired WP in the submenu C4.1 (standard weekly program) for this purpose.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF Maximum 4 controllers can be connected. E11 = Software version: Query to the current state of the software version of the main board and controller E12 = Resetting to factory setting All parameters can be reset to factory setting.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF MENU Operating menu Initial start-up (A1) - Address 1-2-3-4 - Language setting - Date / Time Address & Language & Date / Clock ..............NOTES: .
Page 28
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF Monday (C4.1.3) C413 Monday Level Time Level Clock Exit C414 Monday (C4.1.4) Monday Level Time Level <Clock> Level C415 Monday (C4.1.5) Monday Level Time Level <Level>...
Page 29
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF C552 C551 Interval time (C5.5.2) Interval time Speed step 1-24 h factory setting 1h Speed step (C5.5.1) Level 1 – AB Level 1 - AB ...
Page 30
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF Switching steps (D1.3) D13 00 % r.F Switching steps Factory setting 10 Change Next Run on time (D1.4) D14 Run on time 1-4 hours Facrory setting 2 1-4 hours Change Exit...
Page 31
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF D61 Intake/Extract air level (D6) Speed step Speed step intake (D6.1) intake air Level 1-4 Factory setting 2 Level 1-4 Intake/Extract NOTES: ..............air level Change Next...
Page 32
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF Knob light (D11) D111 Setting location light (D11.1) Setting location light 0-100 % Factory setting 50 % Knob light NOTES: ..............Change Next .
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Error menu / Error message in display In case of an error the error message is indicated. Burn time see display lighting. Fehlermenü/Fehleranzeige im Display If the display is off, the rotory encoder flashes red! Bei einem Fehler wird die Fehlermeldung angezeigt, Leuchtdauer siehe Displaybeleuchtung.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF CHAPTER 5 Electrical connection ELECTRICAL CONNECTION All work must be carried out with the equipment fully isolated from the power supply The electrical connection DANGER are to be carried out in accordance with the relevant wiring diagram and are only to be done by a certified electrician All relevant safety regulation, national standards and norms are to be adhered to.
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF CHAPTER 6 Condensate removal CLEANING AND MAINTE- During the heating period the humidity of the extract air condenses to water. When bathing, while having a sauna as NANCE well as when drying the laudry or with new buildings, condensate can richly build up.
Page 37
Installation and Operating Instructions Wall installed unit KWL EC 60 Pro / ... Pro FF...
Page 38
FRANÇAIS SOMMAIRE INFORMATIONS GENERALES PAGE 1 CHAPTER 1 Informations importantes ..................................Page 1 Précautions et consignes de sécurité ..............................Page 1 Demande de garantie – Réserves du constructeur ..........................Page 1 Réglementation – Normes ..................................Page 1 Réception de l’envoi ....................................Page 1 Stockage ......................................
Il en sera de même pour toute implication de responsabilité du fabricant. L’utilisation d’accessoires et d’équi- pements qui ne sont directement fournis ou conseillés par Helios n’est pas permise. Nous déclinons toute responsabi- lité en cas de défaut consécutif à leur utilisation.
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF 111 Raccordement électrique Mettre impérativement l’appareil hors tension avant tous travaux d’entretien ou à l’ouverture du boîtier de DANGER commande ! Le branchement électrique doit être réalisé, conformément aux schémas de raccordement ci- dessous, uniquement par un électricien qualifié L’alimentation électrique doit être maintenue hors tension jusqu’à...
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF CHAPTER 3 Montage mural du kit gros oeuvre KWL 60 RS MONTAGE / DISPOSITION Effectuer un carottage dans le mur (voir Fig. 5). Insérer le manchon de raccordement mural dans le mur et l’enduire. Pour éviter une déformation du manchon lors de la pose de l’enduit, la croix de renforcement en polystyrène POINT IMPORTANT (voir Fig 1) doit être insérée Après l’enduit, il convient de la retirer!
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Montage rallonge manchon mural KWL 60 WV Fig 9 max. 560 mm de paroi entre les deux rallonges max. 560 mm Assembler la rallonge Wandring auf Wanddicke bei zwei manchons...
Page 43
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Pour sélectionner le programme désiré, accédez au sous-menu C4.1. Pour personnaliser un programme de semaine, se rendre dans le sous-menu C4.2 (Programme hebdo individuel) et entrez vos critères pour chaque jour de la semaine. C5 = Mode vacances : Vous pouvez programmer dans le menu les périodes pendant lesquelles vous êtes absent.
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF E11 = Version logiciel : Indique la version du programme de la platine et de la commande à distance. E12 = Reset réglages usines : Tous les réglages peuvent être réinitialisés selon les configurations d’usine.
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF MENU Arborescence du menu Première mise en route (A1) - Adresse 1-2-3-4 - Réglage langue - Date / Heure Adresse & Réglage langue &...
Page 46
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Lundi (C4.1.3) C413 Lundi Vit. Heure Vit. Heure Sortie C414 Lundi (C4.1.4) Lundi Vit. Heure Vit. Vitesse <Heure> C415 Lundi (C4.1.5) Lundi Vit. Heure Vit.
Page 47
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF C552 C551 Intervalle temps (C5.5.2) Intervalle temps Vitesse 1-24 h Réglage usine 1 h Vitesse ventilation (C5.5.1) 1 - 24 h Vitesse 1 - REP Vitesse 1 - REP ...
Page 48
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Etages commutation (D1.3) D13 Etages commutation 00 % HR Réglage usine : 10 00 % HR Modifier Suivant Post-ventilation (D1.4) D14 Post-ventilation 1-4 heures Réglage usine : 2 1- 4 h Modifier...
Page 49
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF D61 Vitesse de ventilation de soufflage/ Vitesse de ventilation de soufflage d‘extraction (D6) Vitesse de ventilation de soufflage (D6.1) Vitesse 1 - 4 Vitesse 1-4 Vitesse de ventilation Réglage usine : 2...
Page 50
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Eclairage de la molette (D11) D111 Réglage de la veilleuse (D11.1) Réglage de la 0-100 % veilleuse Réglage usine : 50 % Eclairage de la ...
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Montage- und Betriebsvorschrift Wand-Einbaugerät KWL EC 60 Pro / ... Pro FF Liste des messages d’erreur Fehlermenü/Fehleranzeige im Display Si un dysfonctionnement survient, un message d’erreur s’affiche. Pour le réglage du témoin défaut voir paragraphe Eclaira- ge écran.
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF CHAPTER 5 Raccordement électrique RACCORDEMENT Mettre impérativement l’appareil hors tension avant tous travaux d’entretien ou à l’ouverture du boîtier de ELECTRIQUE commande! Le branchement électrique doit être réalisé, conformément aux schémas de raccordement ci-des- DANGER sous, uniquement par un électricien qualifié Les normes et consignes de sécurité...
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Schéma de branchement SS-958 pour KWL EC 60 Pro / Pro FF Fig13 Fig 13...
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF Evacuation des condensats CHAPTER 6 Pendant la saison de chauffe, l’humidité de l’air repris peut condenser dans l’échangeur. Lors de bains, douches, NETTOYAGE ET saunas, séchage du linge ou dans les constructions neuves, l‘eau contenu dans l‘air ambiant peut condenser abon- ENTRETIEN damment.
Page 55
Notice de montage et d’utilisation Groupe double flux mural KWL EC 60 Pro / ... Pro FF...
Page 56
HELIOS Ventilatoren GmbH + Co KG · Lupfenstraße 8 · 78056 VS-Schwenningen HELIOS Ventilateurs · Le Carré des Aviateurs · 157 avenue Charles Floquet · 93155 Le Blanc Mesnil Cedex CH HELIOS Ventilatoren AG · Tannstrasse 4 · 8112 Otelfingen GB HELIOS Ventilation Systems Ltd.