Advertisement
Hold the floor head with left hand, use right hand to insert the metal tube vertically into floor head, align with the conductive needle, press the tube until a "click" sound is heard.
Attention: Keep the handle and floor head in the same direction, conductive needle shall align with the socket.
When packing, storing or cleaning, if the electric floor head needs to be removed, press the brush release button and pull the metal tube in the direction shown in the picture to take out floor head.
Hold battery pack, align with guiding slot on handheld vacuum body, slide in battery pack in the arrow direction in the picture. And then pull the battery pack after installation to make sure it does not get loose.
Attention: when the vacuum cleaner is long idled, please remove the battery, pack the machine and store it in a cool and dry place, avoid direct sunlight or humid environment.
First, assemble floor head and metal tube according to the method of assembling electric floor head with metal tube.
Then, as shown by the arrow, align the conductive needle of the metal tube with the coupler of the handheld vacuum suction nozzle, push metal tube upward until a "click" sound is heard.
For the convenience of use, this product is specially equipped with some accessories for the hand-held part of the vacuum cleaner. When you use the handheld vacuum cleaner alone, you can directly connect the accessories according to your needs or connect the accessories through the stretch hose.
Attention:
The product can be charged in two ways:
Attention:
Take the vacuum cleaner off the storage holder, press the on/off button to start or stop the vacuum cleaner. Mode button can adjust working mode. When machine is turned on, it works in Auto mode, press the mode button to switch to the sequence of Turbo- Max - Eco-Auto mode. During mode switch the mode will be displayed in LCD screen and there is voice reminding.
Middle of LCD screen displays product run time left in current mode. When mode is changed, left run time will also change accordingly.
When product works in Max mode and battery power drops below 20%, to extend product run time, product will automatically switch from Max to Eco mode. After battery is charged to higher than 20% power, product can work in Max mode.
When the product is working in Auto mode, it will adjust working power basing on the dust content and the floor type it detects, in order to achieve higher cleaning efficiency. Under Auto mode, LCD screen display Auto regardless how high the working power is.
The product is equipped with dust content sensor. On LCD screen bottom there are 4 round light circles to display the dust content of 4 kinds of particles with diameter of 10μm-60μm/60μm180μm/180-500μm/>500μm respectively. The circles for different dust particle size are in four different colours: red, yellow, blue and green. As dust content decreases from high to low, the colour fill in the circles accordingly. Cleanness of the cleaning surface can be visually displayed through LCD screen.
Colour fills in circles when dust content increases
The flexible metal tube has two modes: vertical and bending. The vertical mode is equivalent to the normal metal tube. The bending mode can be used for cleaning under the sofa, table or bed, etc. When the bending mode is needed, press the release button and the metal tube can achieve 0-90°bending angle.
Electric floor head is suitable to clean all kinds of floor like hard floor, tile and carpet etc. Product comes with an extra carpet brushroll can be replaced to the floor head to deep clean carpet.
Attention: During the operation of the electric floor head, if there is a large volume of foreign matter inhaled or too much fiber wound, or even a child in the play of the machine mistakenly put his hand into the nozzle, resulting in the brushroll abnormal stop, the electric floor head will stop working, in order to protect personal safety and brush motor.
Crevice tool: suitable for cleaning crevice, door or window corners and other narrow gaps.
Upholstery tool: suitable for cleaning closet, windowsill, sofa and table surface.
Soft brush: suitable for cleaning easy to scratch furniture like bookshelf, handicraft etc.
Stretch hose: suitable for connecting with other tools to clean hard to reach areas.
Electric mattress head: Suitable for sofa and bed mattress. The brushroll beats out and then cleans the dust mite and allergen from deep sofa or bed.
Connector: Can be connected to other tools and bend to different angle to clean dust on top of high cabinets or dust on the roof.
Attention:
Press the battery release button, pull battery pack out backward and place the battery in a plastic bag, then store it in a dry place.
When the vacuum is long idled, remove the battery, pack the machine and store it in a cool and dry place, do not put in direct sunlight or humid environment.
Please check the following issues before sending to designated repair agent.
Trouble | Possible Causes | Solutions |
Motor does not work | Battery has no power | Charge the vacuum cleaner |
Metal tube, floorhead, battery pack and vacuum cleaner is not assembled correctly | Check the accessories are assembled correctly to the vacuum cleaner | |
Suction drops | Dust cup full | Clean dust cup |
Filter blocked | Clean or replace filter | |
Floorhead air path blocked | Clean floorhead air path | |
Short working time after charging | Machine not fully charged | Follow instruction manual to fully charge the battery |
Battery old aging | New batteries can be bought from local distributor | |
Dust content indicator is always red | Dust sensor covered by dust | Clean the dust on the dust sensor which is located in the suction inlet of the handheld vacuum cleaner |
Defect of F1 to F8 is as following:
Code | Defect | Solutions |
F1 | Battery pack nickel strip broken | Replace or repair battery pack |
F2 | Charger defect | Replace charger |
F3 | Vacuum motor short circuit | Replace vacuum motor |
F4 | Battery cell defect | Replace or repair battery pack |
F5 | Vacuum motor 1st over current protection | Replace vacuum motor |
F6 | Vacuum motor 2nd over current protection | Replace vacuum motor |
F7 | PCB defect or PCB leadwire loose | Replace PCB or PCB leadwire |
F8 | Battery pack PCB defect | Replace or repair battery pack |
Attention: If any other failures occurred, which need professional tools, in order to avoid danger, the machine must be repaired or replaced by manufacturer, other maintenance offices or professionals from similar offices.
Model No | H10 Pro |
Rated voltage | 28.8V![]() |
Rated power | 650W |
Adaptor Input Voltage | 100-240V ~ 50-60 Hz 0.8A |
Adaptor Output Voltage | 34.2V![]() |
Electric Floorhead Model No | T-EB110VA |
Electric floor head rated power | 50W |
Battery pack capacity | 3000mAh |
Charge time | 4-5h |
Manufacturer | Kingclean Electric Co., Ltd |
Address | No.1 Xiangyang Road, Suzhou New District, Jiangsu Province 215009, China |
This vacuum cleaner is designed for home use. Do not use it for commercial or other purposes.
Please read this instruction manual carefully before use, properly save and store it for future use.
Do not put the vacuum close to fire or other high temperature facility.
Do not use or store the machine under extreme bad conditions, for example, extreme temperature. It is recommended to use it indoors between the temperature of 5°C to 40°C. Store the machine in dry place and avoid direct sunlight.
Fully charge the battery before first use or after long storage.
Before using the vacuum, make sure brushroll is assembled, otherwise, it may lead to motor fan blockage, causing motor burn out.
Please do not use the vacuum to pick up detergent, oil, glass slag, needle, cigarette ash, wet dust, water, matches, etc.
Please do not use the vacuum to pick up tiny particles such as cement, gypsum powder, wall powder, or large objects such as paper balls, otherwise it will cause malfunctions such as blockage and motor burnout.
Avoid blockage to air inlet or brushroll, it may cause motor failure.
Do not put your hand or foot into floorhead inlet to avoid body hurt.
Do not pour or splash water or other liquids into the machine to avoid short circuit to burn out the machine.
If the brushroll is not working, please check whether the brushroll is entangled with hair or other long fiber, clean it in time.
When storing the machine for a long time, ensure that the battery is fully charged before storage and charge the machine at least every three months.
Unplug the charger to clean or repair the machine. Hold the charger when plugging or unplugging it, and do not pull the charging cord.
Use a dry cloth to clean the machine. Liquids like gasoline, alcohol, lacquer thinner will cause crack or colour fading and cannot be used.
If the machine is not working after fully charged, it must be checked and repaired in our designated office, please do not dismantle the machine on your own.
Discarded machine contains batteries. They should be recycled safely. Do not discard them randomly.
If there is damage on power cord, to avoid danger, it should be replaced or repaired by manufacturer, repairing agency or professional person.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
The appliance is only to be used with the power supply unit provided.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the H10 Pro that isn't answered in the manual? Leave your question here.