JIMMY BD7 Pro - Anti-Mite Vacuum Cleaner Manual

Products Installation

Parts Name

Packing List

Anti-mite vacuum cleaner x 1
Adapter x 1
Battery pack x 1
Cleaning brush x 1
HEPA filter x 1
User manual x 1

Battery pack removal and assembly

Press and hold the release latch of the battery pack, and take out the battery pack in the direction indicated by the arrow. Assemble battery pack into main body in opposite sequence. (Figure 1)

Charging

Note:

1. When using this product for the first time, the battery power of the vacuum cleaner may not be full. Need to use charger to fully charge the battery before using.
2. When using the anti-mite vacuum cleaner for the first three times, please charge up to 12 hour each time.

When the power of the vacuum cleaner is insufficient, please charge the vacuum cleaner in time; When the voltage is too low, in order to protect the battery, it will automatically power off, and the vacuum cleaner must be charged at this time. Plug the adapter plug into the AC power socket to start charging. The LED screen of the display screen is "red" when the product is charging.

When the power display icon on LED screen turns to "white", the vacuum cleaner has been fully charged. Please pull the plug out of the AC socket in time.

Use of the Product

Function description

Vacuum+Tap+UV Mode
After power on, the anti-mite vacuum cleaner starts with Vacuum +Tap +UV mode by default, product power is in normal mode, the corresponding indicator light will be on, and the machine will start vacuuming function, brushroll tapping function, the UV-C light dust mite-removal function and the negative ion function; Press the mode button to switch to turbo mode.

Vacuum+UV mode
When product is in Vacuum+Tap+UV mode, keep pressing mode button for 3 seconds to change to Vacuum+UV mode. Corresponding indicator will be one and product will start vacuuming, UV-C light dust removal and negative ions function. Press mode button in this status, product will switch to Turbo mode.

Dust level display
When the cleaned surface is in a clean state, the dust level bar is blue. When the cleaned surface is slightly dirty, the dust level bar is orange. When it is in a dirty state, the dust concentration bar is red. As the dust level decreases, the dust level bar slowly changes from red to orange to blue.

Battery power display
The battery power display is in the form of light band, which is divided into five grids, each representing 20% of the power;
When the power is 100% during the discharge process, the five indicator lights are cold white, and the corresponding indicator lights are off for every 20% of the power consumption. When the power is 10% left, the indicator lights are red to remind charging;
During the charging process, the red light will light up and flash when the power is ≤ 10%, and the cell will turn into a cold white light and start flashing when the power is greater than 10%;
When the power reaches 20%, the next grid light will turn on cold white with flashing. When the power reaches 40%, the next grid light will jump to the next grid light after every 20% of the power is fully charged. When battery power is full, the five grids are fully filled with cold white light.

Brushroll blockage indicator
This indicator flashes when the brushroll is blocked.

Cleaning and maintenance

Note:

1. HEPA filter is available for sale at JIMMY distributor.
2. It is recommended to clean the dust cup in time after each use. When there is too much dust to cause HEPA blockage, it needs to be cleaned in time or replaced if necessary.

Cleaning of dust cup

Turn off the product, remove the dust cup according to the instruction on the dust cup; Align the dust cup with the garbage can, press the bottom cover release button, open the bottom cover, and pour out the garbage. Hold the dust cup with one hand and pull out the filter assembly with the other hand.
(Figures 2, 3)

HEPA filter cleaning

Turn HEPA bottom cover clockwise; Take out the HEPA assembly downward, tap the HEPA assembly downward to clean the dust, or use a brush to clean the dust and other debris on the HEPA assembly. After cleaning the dust cup and HEPA assembly, put the HEPA into the filter assembly and then rotate it anticlockwise to fix it. After the "click" sound is heard when rotating, and the HEPA is assembled in place without loosening.
(Figures 4, 5)

Note:

1. Do not miss HEPA filter!
2. If too much dust is accumulated in the dust cup, clean the dust cup and filter assembly with water, and wipe them with dry cloth. Pay attention that HEPA filter need to be washed as less as possible. Clean the dust and foreign matters on HEPA filter by tapping, and ensure that the dust cup and filter assembly are completely dry before installation.

Brushroll cleaning and assembly

Note: When cleaning the brushroll, be sure to disconnect the power supply to prevent the brushroll from starting by mistake and cause human injury.

Turn off the machine, push the brushroll cover latch. Turn it from the closed state to the open state, and then remove brushroll cover and take out brushroll. Clean brushroll with cleaning brush. (Fig.6)

After cleaning the brushroll, install the brushroll and brushroll cover back to main body in turn, and lock the brushroll latch.

Dust sensor cleaning

Dust sensor is installed inside of air inlet. Use mini brush to clean inner wall of air inlet to avoid too much dust accumulating on dust sensor and cause abnormal display of dust level.
(Figures 7)

Maintenance and Storage

Please clean dust cup and filter after each use for further use. It is recommended to replace a filter after 30-50 hours of working time(depending on specific situation) for better use.

Any paper, lead glass, plastic will greatly affect the effect of UV light. Please wipe and clean the UV tube regularly for better use.
Do Not touch the UV tube as dirt will affect UV light effect.

Put the machine in cool and dry place if the machine is to be idled. Do Not leave it in direct sunlight or humid environment.

Trouble Shooting

Please check the following trouble points before go to the maintenance department.

Note: If there are other faults, special tools must be used, please contact after sales service for guidance.

Product Specifications

Technical Parameter

Model No	BD7 Pro
Rated voltage	28.8V
Rated power	250W
Charger rated input	100-240V~ 50-60Hz 0.8A
Charger rated output	34.2V 600mA
Battery capacity	2000mAh
Charge time	3-4h

Circuit Diagram

Cautions

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision.

For the purposes of recharging the battery, only use the detachable supply unit<ZD024M342060EU or ZD24W342060EU > provided with this appliance.

Do not touch the rotating parts. Remove any items (hair, fluff etc.) that might block the brushes and wheels.

This appliance contains batteries that are only replaceable by skilled persons.

The appliance is only to be used with the power supply unit provided with the appliance.

Please read this instruction manual carefully before use, properly save and store it for future use.

The product design and spec in the manual may slightly vary from the actual product. Please take physical product shall prevail.

This product is an electric appliance. Do not let the product run alone without supervision.

If the product is long idled, turn off power, remove battery and store battery properly. Unplug the the power cord ply. Keep hands dry when unplugging the power plug to avoid electric shock.

Cut off power when machine is under cleaning, repairing or is not used.

Do not let the power cord pass through sharp objects, and avoid dragging the power cord to move the machine to avoid damaging the power cord.

Do not use product to pick up heating objects such as carbon and cigarette butts, sharp objects such as broken glass, corrosive liquids, flammable and explosive substances such as gasoline and alcohol, otherwise it may damage the product or cause fire, thus causing personal injury and other accidents.

Do not use this machine to pick up water or wet dust, and avoid the machine from being exposed to rain, water or being used in wet places (such as bathrooms, washrooms, laundry rooms, etc.) to avoid failure.

Avoid the product approaching heating appliances or being exposed to the sun to avoid fire.

Do not let children play with or operate the product to avoid accidents.

Avoid product running for a long time when the suction port is blocked to avoid damage.

The product is equipped with UV-C light. Do not view the bottom of the machine when the power is turned on to prevent UV rays from causing harm to human body.

Please do not let UV-C light shine on plants to avoid damaging them. Do not concentrate UV-C light in one place for continuous use, which may cause damage to the cleaned objects.

Do not sit on the product to avoid damage.

Do not remove brushroll when machine is powered on or running to avoid damage.

When storing the machine for a long time, ensure that the battery is fully charged before storage and charge the machine at least every three months.

Use a dry cloth to clean the machine. Liquids like gasoline, alcohol, lacquer thinner will cause crack or colour fading and cannot be used.

Discarded machine contains batteries. They should be recycled safely. Do not discard them randomly.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download JIMMY BD7 Pro - Anti-Mite Vacuum Cleaner Manual