Table of Contents
Advertisement
en Rapid heating
8.8 Keeping warm over an extended period
You can use your appliance to keep meals warm for up
to 24 hours without changing the behaviour of the ap-
pliance. Use the time functions and change the basic
settings.
Note: If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
ensure that the behaviour of the appliance is not
changed during operation, only open the appliance
door once the set time has elapsed.
Change the basic settings.
1.
→ "Basic settings", Page 17
Change the "Lighting" basic setting to "Always
‒
off".
Change the "Standby screen" basic setting to
‒
"On".
Change the "Signal tone" basic setting to "Very
‒
short duration".
a This will ensure that the light in the cooking com-
partment is always off while the appliance is in oper-
ation and when you open the appliance door. The
clock display does not change. The duration of the
signal tone is reduced at the end of the operation.
Rapid heating
9 Rapid heating
To save time, rapid heating
ing time for set temperatures over 100 °C.
Rapid heating is possible for the following types of
heating:
¡ 3D hot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note: Do not set a cooking time until rapid heating has
come to an end.
Time-setting options
10 Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
12
can shorten the preheat-
Set the required operating mode.
2.
→ "Setting the operating mode", Page 11
→ "Setting the type of heating and the temperature",
Page 11
Set the required cooking time depending on the op-
3.
erating mode.
→ "Setting the cooking time", Page 13
→ "Time-setting options", Page 12
Use "End time" to set the time at which the opera-
4.
tion should end.
→ "Setting the end time", Page 13
→ "Time-setting options", Page 12
Place the food in the cooking compartment before
5.
the appliance starts to heat.
Press
to start the operation.
6.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
7.
When the operation has ended, remove the food
from the cooking compartment. The appliance auto-
matically switches off completely after approximately
15 to 20 minutes.
Note: If required, change the different basic settings
again.
Set a suitable type of heating and a temperature of
1.
at least 100 °C.
Rapid heating automatically switches on at temper-
atures of 200 °C and above.
2.
Press "Rapid heating".
a The
symbol lights up red.
Press
to start the operation.
3.
a Rapid heating starts.
a Once rapid heating has ended, a signal sounds.
The
symbol changes back to white.
Place the food in the cooking compartment.
4.
Cancelling rapid heating
Press
on the display.
1.
Press "Rapid heating".
2.
a The
symbol changes back to white.
Time-setting
Use
option
End time
Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
Advertisement
Table of Contents
