Etekcity EHS-18 - Digital Hanging Scale Manual

Package Contents

1 x Digital Hanging Scale
2 x 3V CR2032 Batteries (Pre-Installed)
1 x Carrying Pouch
1 x User Manual

Specifications

Function Diagram

1. Handle
2. LCD Display
3. ON/OFF Button
4. TARE Button
5. UNIT Button
6. Hook
7. Battery Compartment
8. Hook Storage

LCD Display

1. Measured weight is less than the calibrated tare weight
2. Displayed weight is the tared weight
3. Last measured weight
4. Weight in grams
5. Weight in ounces
6. Weight in kilograms
7. Weight in pounds
8. Maximum weight capacity has been exceeded
   (remove object from hook immediately)
9. Battery low

Setup

Battery Installation

1. Use a screwdriver to loosen the screw.
2. Open the battery cover.
3. Remove the insulation strip to activate the batteries.
   
4. When replacing the batteries, make sure to insert them under the proper polarity.

Operation

Weight Measurement

1. Press ON/OFF and the screen will light up. Wait for " " to appear on the screen.
   
2. Hang the object you want to measure on the hook.
3. Lift the scale with the object and hold still until the weight measurement stabilizes. The display will show the weight and "Hold".
4. To measure another item, remove the object and repeat steps 2 and 3.
5. Press ON/OFF to turn the scale off. The scale will automatically turn off if the scale is inactive for 60 seconds.

Note: To avoid result inaccuracy, keep the scale upright when measuring. Do not touch or move the scale during measurement. Always grasp the scale by the handle.

Unit Conversion

Press UNIT repeatedly to change the unit of measurement (oz / g / lb / kg).

Data Hold Function

Once the weight has stabilized and "Hold" appears on screen, the weight will stay on the screen for 60 seconds, or until you measure another object or press TARE.
Turning the data hold function on or off:

1. When the scale is on, press and hold TARE for 3 seconds.
2. Press UNIT to alternate between turning data hold function on or off.
   Hoon - Data hold function on
   HooF - Data hold function off
3. Press TARE to confirm selection.

Tare Function

The tare function allows users to weigh an object inside a container by subtracting the weight of the container from the total weight.

1. Hang the container on the weighing scale hook and allow the weight to stabilize and lock (the word "Hold" will appear).
2. Hold the scale stable and press TARE to tare the current weight. The display will show "".
3. Place the object you want to weigh inside the container and the scale will calculate the weight of the object without the weight of the container.

Care & Maintenance

• Do not use chemical detergents to clean the scale. Use a soft, damp cloth if needed.
• If not in use for a long period of time, remove the batteries and store the scale in a cool, dry environment to avoid circuit damage.

Replacing Batteries

1. Locate the battery compartment on the back of the scale and remove the battery compartment cover.
2. Ensure the + side of the battery is facing up and insert the batteries into the battery slots.
   
3. Replace cover.
4. Use a screwdriver to tighten the screw.

Safety Information

Follow all instructions and safety guidelines. Read all instructions before using.

• Do not exceed the weight capacity of 110 lb (50 kg). An overload indicator will appear on the digital display if the limit is exceeded.
• This scale is not intended for commercial or heavy-duty use. Household use only.
• Do not throw or strike the scale and do not submerge the scale in water.

Customer Support

If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.

Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: support@etekcity.com
Toll-Free: (855) 686-3835

Support Hours
Mon–Fri, 9:00 am–5:00 pm PST/PDT
*Please have your order invoice and order ID ready before contacting Customer Support.