Video-inserter compatible with opel, chevrolet and buick with cd500, dvd600, dvd800, dvd900, cd600intellilink and dvd950intellilink infotainment (19 pages)
Video inserter compatible with mercedes benz vehicles with comand online ntg5.5 with 12” monitor and double fakra connector at the head unit (21 pages)
Page 1
Video inserter RL2-LR16 Compatible with Jaguar vehicles Land Rover vehicles with Incontrol Touch infotainment and 8inch monitor Video-inserter for rear-view camera Product features • Video-inserter for factory-infotainment systems • 1 CVBS Input for rear-view camera • Automatic switching to rear-view camera input on engagement of the reverse gear •...
Connection - Quadlock - CAN 2.5. After-market rear-view camera 2.5.1. Case 1: Interface receives the reverse gear signal 2.5.2. Case 2Interface does not receive the reverse gear signal 2.6. Picture settings and guide lines 3. Specifications 4. Technical support Version 21.10.2022 HW: 25(V21) RL2-LR16...
Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 21.10.2022 HW: 25(V21) RL2-LR16...
Incontrol Touch with 8inch 16:9 Land Rover without Meridian-Sound-System monitor with Touch-Screen Menu 4 Only for vehicles with automatic gear shift Limitations Guidelines Displayed guidelines are not available in all vehicles. Video input signal Only NTSC video sources compatible. Version 21.10.2022 HW: 25(V21) RL2-LR16...
OFF (oben) No function Set to OFF Vehicle selection Set to OFF No function Set to OFF No function Set to OFF After each Dip-switch-change a power-reset of the video interface has to be performed! Version 21.10.2022 HW: 25(V21) RL2-LR16...
The interface needs a permanent 12V source! 2.1. Place of installation The interface is supposed to be installed at a suitable location behind the vehicle`s head- unit. Version 21.10.2022 HW: 25(V21) RL2-LR16...
Connect the opposite water-blue Fakra socket of the enclosed video output cable to the Fakra connector of the head unit as shown in the diagram aboveabove. Version 21.10.2022 HW: 25(V21) RL2-LR16...
Page 9
Connect the previously detached metal socket of the video output cable to the Fakra connector oft he head-unit, shown in the diagramm above. Version 21.10.2022 HW: 25(V21) RL2-LR16...
40pin quadlock connector of the head-unit. Connect the 10-pin PNP power/CAN cable‘s 10-pin connector to the 10-pin connector of the video interface. Connect the power supply for the rear view camera to the 10-pin PNP power/CAN cable‘s grey cable „Reverse-OUT“. Version 21.10.2022 HW: 25(V21) RL2-LR16...
(e.g AC-RW- 1230 with wiring AC-RS5) or filter (e.g. AC-PNF-RVC) is required. The following diagram “Case 2: Interface does not receive the reverse gear signal” shows the connection type of the relay Version 21.10.2022 HW: 25(V21) RL2-LR16...
Connect stabile and permanent +12V to the relay’s input connector (30). Note: BEFORE completing the installation, check that the switchover to the rear-view camera takes place by applying +12V current to the blue coloured "Reverse-IN" wire. Version 21.10.2022 HW: 25(V21) RL2-LR16...
Note: If there is no communication between interface and the vehicle`s CAN-bus (several vehicles aren’t compatible), the reverse gear guide-lines can`t be shown during the vehicle’s operation, even if they once appear after having switched the system to powerless! Version 21.10.2022 HW: 25(V21) RL2-LR16...
80 x 22 x 110 mm (W x H x D) Technical Support Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH...