Table of Contents
Advertisement
Quick Links
Video inserter
RL2-LR14
Compatible with
Jaguar
vehicles
Land Rover
vehicles
with Touch-Screen Navigation version 3 infotainment
Video-inserter for rear-view camera
Product features
Video-inserter for factory-infotainment systems
1 CVBS Input for rear-view camera
Automatic switching to rear-view camera input on engagement of the reverse gear
Activatable parking guide lines for rear-view camera (not available for all vehicles)
Video-inputs NTSC compatible
Version 21.10.2022
HW: 25(V21)
RL2-LR14
Advertisement
Table of Contents
Related Manuals for NavLinkz RL2-LR14
Summary of Contents for NavLinkz RL2-LR14
- Page 1 Video inserter RL2-LR14 Compatible with Jaguar vehicles Land Rover vehicles with Touch-Screen Navigation version 3 infotainment Video-inserter for rear-view camera Product features Video-inserter for factory-infotainment systems 1 CVBS Input for rear-view camera Automatic switching to rear-view camera input on engagement of the reverse gear ...
-
Page 2: Table Of Contents
Connection – 10pin Power/CAN cable 2.5. After-market rear-view camera 2.5.1. Case 1: Interface receives the reverse gear signal 2.5.2. Case 2Interface does not receive the reverse gear signal 2.6. Picture settings and guide lines 3. Specifications 4. Technical support Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 3: Prior To Installation
Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 4: Checking The Compatibility Of Vehicle And Accessories
Land Rover vehicles model years 2015-2016 (not 2017) with Meridian-Sound-System Only for vehicles with automatic gear shift Limitations Guidelines Displayed guidelines are not available in all vehicles. Video input signal Only NTSC video sources compatible. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 5: Boxes And Connectors - Video Interface
OFF (oben) No function Set to OFF Vehicle selection Set to ON No function Set to OFF No function Set to OFF After each Dip-switch-change a power-reset of the video interface has to be performed! Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 6: Installation
The interface needs a permanent 12V source! 2.1. Place of installation The interface is supposed to be installed at a suitable location behind the vehicle`s head- unit. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 7: Connection Schema
2.2. Connection schema Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 8: Connection - Picture Signal Cable
Connect the opposite female water-blue Fakra connector of the enclosed video output cable to the male fakra connector of the head unit as shown above. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 9: Connection - 10Pin Power/Can Cable
16pin connector of the head-unit. Connect the 10pin PNP power/CAN cable‘s 10pin connector to the 10pin connector of the video interface. Connect the power supply for the rear view camera to the 10pin PNP power/CAN cable‘s grey cable „Reverse-OUT“. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 10: After-Market Rear-View Camera
(e.g AC-RW- 1230 with wiring AC-RS5) or filter (e.g. AC-PNF-RVC) is required. The following diagram “Case 2: Interface does not receive the reverse gear signal” shows the connection type of the relay. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 11: Case 2Interface Does Not Receive The Reverse Gear Signal
Connect stabile and permanent +12V to the relay’s input connector (30). Note: BEFORE completing the installation, check that the switchover to the rear-view camera takes place by applying +12V current to the blue coloured "Reverse-IN" wire. Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 12: Picture Settings And Guide Lines
Note: If there is no communication between interface and the vehicle`s CAN-bus (several vehicles aren’t compatible), the reverse gear guide-lines can`t be shown during the vehicle’s operation, even if they once appear after having switched the system to powerless! Version 21.10.2022 HW: 25(V21) RL2-LR14... -
Page 13: Specifications
80 x 22 x 110 mm (W x H x D) Technical Support Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH...
Need help?
Do you have a question about the RL2-LR14 and is the answer not in the manual?
Questions and answers