SIGMATEK ETT 1033 Operating Manual
  1. Manuals
  2. Brands
  3. SIGMATEK Manuals
  4. Control Panel
  5. ETT 1033
  6. Operating manual

SIGMATEK ETT 1033 Operating Manual

Multi-touch operating panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ETT 1033
Multi-Touch Operating Panel
Operating Manual
Date of creation: 13.08.2015
Version date: 20.11.2023
Article number: 01-230-1033-E

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ETT 1033 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SIGMATEK ETT 1033

Summary of Contents for SIGMATEK ETT 1033

  • Page 1 ETT 1033 Multi-Touch Operating Panel Operating Manual Date of creation: 13.08.2015 Version date: 20.11.2023 Article number: 01-230-1033-E...
  • Page 2 (print, photocopy, microfilm or in any other process) without the express permission. We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi- ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through...
  • Page 3 MULTI-TOUCH OPERATING PANEL ETT 1033 Multi-Touch Operating Panel ETT 1033 The Multi-Touch Operating Panel is an intelligent panel for visualizing, operating and moni- toring automated processes. A capacitive touch screen serves as the input medium for process data and parameters.

  • Page 4: Table Of Contents

    ETT 1033 MULTI-TOUCH OPERATING PANEL Contents Technical Data ................ 4 Performance Data ................. 4 Electrical Requirements ............... 5 Terminal ..................5 Environmental Conditions ............6 Display 10.4” XGA ................ 7 Control Unit ................... 7 Digital Outputs ................9 Digital Inputs ................. 9 Miscellaneous ................
  • Page 5 MULTI-TOUCH OPERATING PANEL ETT 1033 Wiring Guidelines ..............22 Ground ..................22 Shielding ..................22 ESD Protection ................22 USB Interface Connections ............22 CAN Bus Setup ..............23 CAN Bus Station Number ............23 Number of CAN Bus Participants ..........23 CAN Bus Data Transfer Rate .............

  • Page 6: Technical Data

    ETT 1033 MULTI-TOUCH OPERATING PANEL Technical Data Performance Data Processor EDGE2 Technology Processor cores Internal cache 32-kbyte L1 Instruction Cache 32-kbyte L1 Data Cache 512-kbyte L2 Cache Internal program and data 512-Mbyte memory (DDR3 RAM) Internal remnant data memory 512-kbyte SRAM (battery buffered)

  • Page 7: Electrical Requirements

    MULTI-TOUCH OPERATING PANEL ETT 1033 Electrical Requirements Supply voltage typically +24 V DC (+18-30 V DC) Current consumption of power typically 760 mA maximum 920 mA supply at +24 V (without externally connected devices) (with externally connected devices) maximum 2 A for 10 s...

  • Page 8: Environmental Conditions

    ETT 1033 MULTI-TOUCH OPERATING PANEL Environmental Conditions Storage temperature -10 ... +75 °C 0 … +55 °C Environmental temperature Humidity 10-95 %, non-condensing Operating conditions Pollution degree 2 Indoor use altitude up to 2000 m EMV resistance in accordance with EN 61000-6-2 (industrial area)

  • Page 9: Display 10.4" Xga

    Cleaning see chapter: Cleaning the Touch Screen The ETT 1033 has a projective capacitive touch screen is built in, with which 10-finger input, Zoom and gesture functions can be implemented. Data can be input using fingers, a projective capacitive touch pen and while wearing thin gloves. The device must always have a good ground connection so that the function of the touch screen is stable.
  • Page 10 ETT 1033 MULTI-TOUCH OPERATING PANEL L'ETT 1033 dispose d’un écran tactile capacitif projectif avec lequel de gestes avec 10 doigts, multi gestes et fonctions zoom peuvent être réalisées. Les données peu- vent être saisies en utilisant les doigts, y compris en portant des gants minces, ou bien un stylo tactile capacitif projectif.

  • Page 11: Digital Outputs

    MULTI-TOUCH OPERATING PANEL ETT 1033 Digital Outputs Number Short-circuit proof Maximum permitted contin- 0,5 A uous load current / channel Maximum total current (all 2 A (100 % of on time) 8-channels)  1 V Voltage drop over power supply (output active) ...

  • Page 12: Miscellaneous

    ETT 1033 MULTI-TOUCH OPERATING PANEL Miscellaneous Article number 01-230-1033 Hardware version Operating system Salamander Standard IP address 10.10.150.1 Standard UL 61010-2-201 Approbations UL, cUL, CE, UKCA Warning to the installer Temperature rating of the cable to be connected to the terminals Temperature resistance of the cable insulation must be above 70 °C...

  • Page 13: Mechanical Dimensions

    MULTI-TOUCH OPERATING PANEL ETT 1033 Mechanical Dimensions Up to HW Version 2.10 20.11.2023 Page 11...

  • Page 14: Starting From Hw Version X.xx

    ETT 1033 MULTI-TOUCH OPERATING PANEL Starting from HW Version 2.20 Page 12 20.11.2023...

  • Page 15: Connector Layout

    MULTI-TOUCH OPERATING PANEL ETT 1033 Connector Layout Backside starting with HW 2.10 Backside up to HW 2.00 X1: Supply (4-pin Phoenix RM 3.5) Function +24 V DC DIG IOs +24 V DC 20.11.2023 Page 13...
  • Page 16 ETT 1033 MULTI-TOUCH OPERATING PANEL X2 and X3: 8 Digital Outputs, 8 Digital Inputs (8-pin Phoenix RM 3.5) Starting with HW 2.10 X2: Pin Assignment Function Output 1 Output 2 Output 3 Output 4 Input 1 Input 2 Input 3...
  • Page 17 By configuring the packet filter (Firewall or Router) accordingly however, it is pos- sible to connect a network with SIGMATEK hardware to a third party network with- out triggering the error mentioned above.
  • Page 18 +3V3 DAT0 DAT1 It is recommended that only storage media provided by SIGMATEK (CompactFlash cards, microSD cards etc.) be used. Order number for 512 Mbyte EDGE2: 12-630-055 The number of read and write actions have a significant influence on the lifespan of the storage media.

  • Page 19: Applicable Connectors

    MULTI-TOUCH OPERATING PANEL ETT 1033 X7: USB 2.0 (Type Mini B) (can be used with OTG cable as USB host, otherwise USB Device for service purposes) Function +5 V X8, X9: USB 2.0 (Type A) Function +5 V_USB It should be noted that many of the USB devices on the market do not comply with USB specifications;...

  • Page 20: Buffer Battery

    ETT 1033 MULTI-TOUCH OPERATING PANEL Buffer Battery The exchangeable buffer battery ensures that the clock time (RTC) and zero voltage safe data is preserved in the absence of a supply voltage. A lithium battery is installed at the manufacturer. The battery has enough capacity to preserve data in the absence of a supply voltage for up to 5 years.

  • Page 21: Exchanging The Battery

    MULTI-TOUCH OPERATING PANEL ETT 1033 Exchanging the Battery 1. Switch off the ETT‘s power supply. From this moment on you have three minutes to exchange the battery. 2. Open the screws of the battery cover. 3. Take out the battery with the help of the strap.

  • Page 22: Cooling

    ETT 1033 MULTI-TOUCH OPERATING PANEL Cooling The terminal's power loss can reach up to 21 Watts. To ensure the necessary air circulation for cooling, the following mounting instructions must be followed! Mounting Instructions Because of the glass surface, you should care that it is not damaged during mount- ing with strong shocks on the edges or corners! Les chocs sur les bords ou sur les coins du terminal survenus lors d’un montage...
  • Page 23 MULTI-TOUCH OPERATING PANEL ETT 1033 The following distance from the housing should be maintained: - Left and right 5 cm - Back side, above and below 10 cm Section side view: section top view The specified mounting distances can be reduced under some circumstances, if appropriate action and technical precautions are taken to drain the resulting loss.

  • Page 24: Wiring Guidelines

    ETT 1033 MULTI-TOUCH OPERATING PANEL Wiring Guidelines Ground The device must be grounded to protective earth (PE) via the blade terminal provided. In addition, ensure that when installing into the control cabinet, a large grounding surface is provided. It is important to establish a low-Ohm connection to ground to ensure error-free function.

  • Page 25: Can Bus Setup

    MULTI-TOUCH OPERATING PANEL ETT 1033 CAN Bus Setup This section explains how to configure a CAN bus correctly. The following parameters must first be set: Station number and data transfer rate. CAN Bus Station Number Each CAN bus station is assigned its own station number. With this station number, data can be exchanged with other stations connected to the bus.

  • Page 26: Can Bus Termination

    ETT 1033 MULTI-TOUCH OPERATING PANEL CAN Bus Termination In a CAN bus system, both end modules must be terminated. This is necessary to avoid transmission errors caused by reflections in the line. For the CAN interfaces, the terminal has a 120  switchable termination resistor the can be turned on and off through the application.

  • Page 27: Process Diagram

    MULTI-TOUCH OPERATING PANEL ETT 1033 10 Process Diagram 20.11.2023 Page 25...

  • Page 28: Status And Error Messages

    ETT 1033 MULTI-TOUCH OPERATING PANEL 11 Status and Error Messages Status and error messages are shown in the status test of the LASAL CLASS software. POINTER or CHKSUM messages can also be shown on the terminal screen. With missing microSD card or a microSD card with a defective operating system version the...
  • Page 29 MULTI-TOUCH OPERATING PANEL ETT 1033 WATCHDOG The program was interrupted via the Possible Causes: watchdog logic. User program interrupts blocked over a longer period of time (STI command forgotten) Programming error in a hardware interrupt. INB, OUTB, INW, OUTW instruc- tions used incorrectly.
  • Page 30 ETT 1033 MULTI-TOUCH OPERATING PANEL STOP BRKPT The CPU was stopped by a breakpoint Info in the program. CPU STOP The CPU was stopped by the program- Info ming software. INT ERROR The CPU has triggered a false interrupt Cause:...
  • Page 31 OP INSTALLED The operating system has been rein- Info stalled. OS TOO LONG The operating system cannot be loaded; Restart; report error to SIGMATEK. too little memory. NO OPERATING Boot loader message. Restart; report error to SIGMATEK. SYSTEM No operating system found in RAM.
  • Page 32 An error has occurred during a floating- ERROR point operation. DIAS-RISC-ERROR Error from the Intelligent DIASMaster. Restart; report error to SIGMATEK. INTERNAL ERROR An internal error has occurred, all appli- Restart; report error to SIGMATEK. cations are stopped. FILE ERROR An error has occurred during a file operation.
  • Page 33 MULTI-TOUCH OPERATING PANEL ETT 1033 C-DIAS ERROR A connection error with a C-DIAS mod- Cause: ule has occurred. The cause of the error is docu- mented in the log file Solution: This depends on the cause S-DIAS ERROR A connection error with a S-DIAS mod- Possible causes: ule has occurred.
  • Page 34 ETT 1033 MULTI-TOUCH OPERATING PANEL C_UNKNOWN_CID An unknown object from a stand-alone or embedded object, or an unknown base class was detected. C_UNKNOWN_CONSTR The operating system class cannot be created; the operating system is proba- bly wrong. C_UNKNOWN_OBJECT Indicates an unknown object in an interpreter program;...
  • Page 35 MULTI-TOUCH OPERATING PANEL ETT 1033 LSL LOAD CONTINUE PRERUN The application is started. PRERESET The application is ended. CONNECTION BREAK 20.11.2023 Page 33...

  • Page 36: Logo Backlighting (Optional)

    ETT 1033 MULTI-TOUCH OPERATING PANEL 12 Logo Backlighting (optional) The application can control the color and intensity of the logo backlighting. This is realized with the three primary colors (red, green, blue) in a value range between 0 and 100.

  • Page 37: Cleaning The Touch Screen

    MULTI-TOUCH OPERATING PANEL ETT 1033 14 Cleaning the Touch Screen CAUTION! Before cleaning the touch screen, the terminal must first be turned off to avoid un- intentionally triggering functions or commands! ATTENTION! Avant de nettoyer l'écran tactile, le terminal doit d'abord être éteint afin d’éviter un déclanchement involontaire des commandes!

  • Page 38: Disposal

    ETT 1033 MULTI-TOUCH OPERATING PANEL 15 Disposal To dispose of the product, the respective, possibly country-dependent, guidelines must be met and followed. Page 36 20.11.2023...
  • Page 39 MULTI-TOUCH OPERATING PANEL ETT 1033 Documentation Changes Change date Affected Chapter Note page(s) 24.08.2015 Label 12.10.2015 3.1 Backside Pin 4 changed 06.11.2015 4 Buffer Battery Zero voltage safe data 23.11.2015 1.6 Control Unit Multitouch distance added 120 Ω instead of 150 Ω...
  • Page 40 ETT 1033 MULTI-TOUCH OPERATING PANEL 01.12.2016 Changed description to "Multi-Touch Operating Panel" 1.7 Digital Outputs Changed values of Maximum continuous current load and Maximum total current 4 Buffer Battery Battery surveillance added 23.01.2017 1.2 Electrical Require- Table content changed ments 1.4 Environmental...

Table of Contents