Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0456
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W
Dimmable Bulb
Work Temperature: -4°F~104°F
Outlet Box
House Grounding Wire
Green Grounding Screw (C)
Mounting Plate (A)
Mounting Screw (B)
Headless Screw (D)
Lock Nut (E)
Fixture Grounding Wire
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Incandescent
Bulb or 20W LED
Wire Connector (F)
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)
Mounting plate (A)
Lock Nut (E)
Fixture
Wire
Glass Shade
Socket Ring
Page 1/4
Mounting Screw (B)
Green Grounding
Screw (C)
Wire Connector (F)
Ball Nut (G)
Rubber Pad (H)
Ball Nut (G)
Fixture
Socket
Vintage Bulb
or Max.20W
Bulb (not included)
181213
Headless
screw (D)
Rubber
Pad (H)
Max.60W
Dimmable LED
Advertisement
Related Manuals for Vaxcel T0456
Summary of Contents for Vaxcel T0456
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0456 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 Installation steps Turn off the power at fuse or circuit box. 1. Thread two headless screws (D) through the mounting plate (A), and then secure them with four lock nuts (E) (two on each side of the mounting plate (A).) Adjust the length of the headless screws (D) if necessary. Note: Make sure the headless screws are lined up horizontally to make the fixture level.
- Page 3 5. Manual Override MODE (nighttime operation only; on at dusk,off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again.
- Page 4 ----In Test Mode, the light stays on full brightness after 5 seconds: 1. If during daytime, make sure the slide switch is at the TEST position. 2. Whether the motion is detected at all time. ---In 3H or 6H Mode, the light is still on full brightness,even though it has been 3 hours or 6 hours after dusk, respectively: 1.